人性的能动本质及其教育—学习的生态性价值

能动性是现实生态人自主生存的本质所在,是人类生命律动性实质存在过程中自我意识与行动不断生发生成和展示创造的生态趋向、主导性能和元生动力,是人类元个体生态及其复合社会生态简单性有效生产和复杂性公平生活有机统一的简明性质量生存的人性主导要素。能动性本质与律动性实质有机结合构成完整的人性全质,合力演化出人类更好生存、享有和发展的丰富文明形态。能动性具有进取性和退行性生存取向的二重性。既定的文化—道德—制度体系的低成本惯性和保守倾向往往会诱发、激活和强化能动性的退行性向,成为文化肥大—贫瘠、教育过度—短缺、学习狭隘—泛化乃至教育—社会被动退化的始佣与元凶。人类必然且必须自觉激发和利用能动性的进取品性与张力,尊重和依托律动性的基本限度与定力,把人类生存引向择良施教、竟优为学、自主互动、进取博弈和实值创新的健全形态。

让学生成为向学的生命

学生是学校生存与发展的根本所在,学生之为学生的根本乃是其积极向学的特性。学生不仅是一种身份描述,更代表着一种生命积极成长的动态过程。因此,对于学生而言,比不停地学知识更重要的是拥有蓬勃向上的向学之心。积极引领向学之心的学校教育乃是超越理智型教育,而上升到生命的教育。为此,学校一方面要强调主动学习,培养学生学习意识,创造条件,提供学生锻炼自我的机会;另一方面,学校要积极行动,创设情境,不断挖掘学生潜能,激励其自我生长。培育健全的生命气象,可谓今日学校教育的根本使命。

Role of inclination angle on columnar-to-equiaxed transition in the eutectic Al-5Mg-2Si alloy fabricated by laser powder bed fusion

In this study,the effect of inclination angles relative to the building direction in the additively manufactured eutectic Al-5Mg-2Si alloy was investigated through the laser powder bed fusion(LPBF).The microstructures and mechanical properties of the Al-5Mg-2Si alloy manufactured with different inclination angles(0°,30°,45°,60°and 90°)were reported and discussed.It is found that the“semicircular”melt pool(MP)in the load bearing face of 0°sample was eventually transformed into“stripe-like”MP in the 90°sample,accompanied by an increased fraction of melt pool boundaries(MPBs).Moreover,the microstructural analysis revealed that the columnar-to-equiaxed transition(CET)of theα-Al grains and eutectic Mg2Si was completed in the 90°sample,which were significantly refined with the average size of 10.6μm and 0.44μm,respectively.It is also found that the 90°sample exhibited good combination of strength and elongation(i.e.yield strength of 393 MPa,ultimate tensile strength of 483 MPa and elongation of 8.1%).The anisotropic mechanical properties were highly associated with the refined microstructures,thermal stress,and density of MPBs.Additionally,the CET driven by inclination angles was attributed to the variation of thermal conditions inside the local MPs.

Microstructure and mechanical properties of 2A12 aluminum alloy after age forming

The comparative experiments of age forming and artificial aging of 2A12 aluminum alloy were carried out. The effect of the age forming on the microstructure and mechanical properties was investigated. The results demonstrate that the grains are further squashed and elongated compared with artificial aging due to the existence of the applied stress during the age forming. Meanwhile, the precipitated phases change from circle shape with random orientation of age forming to long strip shape with uniform orientation of artificial aging. The dislocation configuration in samples changes from ring dislocation or helical dislocation of the artificial aging to long and straight dislocation of the age forming. Otherwise, age forming slightly reduces the tensile properties and fracture toughness of the alloy and enhances its fatigue crack growth rate.

Effects of sputtering pressure on nanostructure and nanomechanical properties of AlN films prepared by RF reactive sputtering

Wurtzite aluminum nitride（AlN） films were deposited on Si（100） wafers under various sputtering pressures by radio-frequency（RF） reactive magnetron sputtering. The film properties were investigated by XRD, SEM, AFM, XPS and nanoindenter techniques. It is suggested from the XRD patterns that highly c-axis oriented films grow preferentially at low pressures and the growth of（100） planes are preferred at higher pressures. The SEM and AFM images both reveal that the deposition rate and the surface roughness decrease while the average grain size increases with increasing the sputtering pressure. XPS results show that lowering the sputtering pressure is a useful way to minimize the incorporation of oxygen atoms into the AlN films and hence a film with closer stoichiometric composition is obtained. From the measurement of nanomechanical properties of AlN thin films, the largest hardness and elastic modulus are obtained at 0.30 Pa.

Microstructure and mechanical properties of isothermal multi-axial forging formed AZ61 Mg alloy

Microstructure and mechanical properties of AZ61 Mg alloy during isothermal multi-axial forging （MAF） were studied. The mechanisms of grain refinement and relationship between the microstructures and mechanical properties were discussed. The results show that the average grain size decreases with increasing the number of MAF passes. The grains are significantly refined at the 1st and 2nd MAF passes, and gradually refined at higher MAF passes. The initial grain size of 148 lam decreases to about 14 gm after 6 MAF passes. The grain refinement occurs mainly by continuous dynamic recrystallization. With increasing the MAF passes, both the tensile strength and the elongation to failure of the alloy are significantly enhanced.

Biomechanical Characteristics of Rape Stalks

[Objective] To study the correlation between the biomechanical properties of rape stalks and rape stem lodging. [Method] Through axial compression tests to the stalks of 4 different rape varieties, the change rules of maximum stem bearing ca- pacity, maximum compressive strength, elastic modulus and moment of inertia along plant height were analyzed, as well as the effect of different varieties and water contents on the biomechanical property indices of rape stalks. [Result] The maximum loads of rape stalks presented liner decrease trend along with the increase of stem height, and all reached the maximums below the height of 50 cm. The maximum stem compressive strength and elastic modulus of the 4 varieties were increased with ascending height, but in a slow rate with small change, thus the modulus of e- lasticity could be considered as unchanged. The maximum bearing capacity, maxi- mum compressive strength and elastic modulus of dry rape stalks were higher than wet stalks, indicating that the water contents of rape stalks had significant effect on their mechanical properties. According to the actual lodging situations in filed, stalks of variety No. 1 owned the worst biomechanical properties and lodging degree, while the biomechanical properties of No. 6 and F5 were better than No. 1 and No. 9, and they also had stronger lodging-resistance. [Conclusion] The study provides parameters and bases for the design of mechanized production and mechanical deep processing of crops, and can better reveal the physical natures of organisms. The methods used in this study can also be used to screen excellent crop stalks.

Mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with diameter of 160 mm

The mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with a diameter of 160 mm manufactured by ＂multi-direction forging（MDF） ＋ extrusion ＋ online cooling＂ technique were investigated by optical microscopy（OM）, scanning electron microscopy（SEM）, X-ray diffraction macro-texture measurement and room temperature（RT） tensile test. The results show that mixed grain structure is caused by the micro-segregation of Al in semi-continuous casting ingot. Homogenization of（380 °C, 8 h） ＋（410 °C, 12 h） cannot totally eliminate such micro-segregation. During MDF and extrusion, the dendrite interiors with 3%-4% Al（mass fraction） transform to fine grain zones, yet the dendrite edges with about 6% Al transform to coarse grain zones. XRD macro-textures of the outer, R/2 and center show typical fiber texture characteristics and the intensity of [0001]//Ra D orientation in the outer（11.245） is about twice as big as those in the R/2（6.026） and center（6.979）. The as-extruded AZ40 magnesium alloy bar has high elongation（A） and moderate ultimate tensile strength（Rm） in both extrusion direction（ED） and radius direction（Ra D）, i.e., A of 19%-25% and Rm of 256-264 MPa; however, yield strength（Rp0.2） shows anisotropy and heterogeneity, i.e., 103 MPa in Ra D, 137 MPa in ED-C（the center） and 161 MPa in ED-O（the outer）, which are mainly caused by the texture.（155 °C, 7 h） ＋（170 °C, 24 h） aging has no influence on strength and elongation of AZ40 magnesium bar.

Effect of finish-rolling conditions on mechanical properties and texture characteristics of AM50 alloy sheet

The conventional hot rolling of AM50 alloy at different roll temperatures and speeds was performed to investigate the effects of finish-rolling conditions on the mechanical properties and texture of rolled sheet. The better combination between strength（ultimate tensile strength： 295 MPa; yield strength： 224 MPa） and ductility（22.9%） can be obtained for the AM50 sheet rolled at the roll temperature of 200 °C with the roll speed of 5 m/min. The yield stress depends strongly on roll temperature, while the texture intensity in rolled sheets is more sensitive to roll speed during hot rolling. Increasing rolling temperature or roll speed can improve the mechanical anisotropy of AM50 rolled sheets.

Analysis of mechanical performance of braided esophageal stent structure and its wires

This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the space spiral curve, a three-dimensional parametrical geometrical model is constructed. The finite element model is built by using the beam-beam contact elements and 3D beam elements. The constituent nitinol wires are assumed to be linear elastic material. The finite element analysis figures out that the radial stiffness of the stent and the stress distribution of the wires are influenced by all the structural parameters. The helix pitch of the wires is the most important factor. Under the condition of the same load and other structural parameters remaining unchanged, when the number of wires is 24, the stress of the wire crosssection is at the minimum. A comparison between the vitro experimental results and the analytical results is conducted, and the data is consistent, which proves that the current finite element model can be used to appropriately predict the mechanical performance of the braided esophageal stents.

Microstructure control and mechanical properties of directionally solidified TiAl-Nb alloys

The double directional solidification（DS） technique was developed to control the lamellar microstructures in primary β TiAl-Nb alloys.Polysynthetically twinned（PST） crystals with lamellar boundaries parallel to or inclined 45o to the growth direction were achieved due to the complete peritectic transformation during directional solidification of the alloys with the dendritic solid/liquid interface.The PST crystals with aligned lamellar boundaries only parallel to the growth direction were produced when lamellar grains with lamellar boundaries in the same orientation were seeded by themselves under appropriate growth conditions.Low boron addition is harmful to align the lamellar orientation because of the growth of non-peritectic α phase.Due to the larger yttria particles and boride ribbons in the directionally solidified TiAl-Nb alloys,the tensile plastic elongations of the alloys are only close to 2%.

Effect of cyclic heat treatment on microstructures and mechanical properties of directionally solidified Ti-46Al-6Nb alloy

The Ti-46A1-6Nb （mole fraction, %） ingots that were directionally solidified by cold crucible were cyclic heat treated at 1330 ℃ in the a phase region. The microstructures and mechanical properties of the ingots before and after heat treatment were investigated. The results show that the large columnar grains are changed into equiaxed grains after heat treatment. The grain size decreases with increasing the cyclic times, which is caused by the recrystallization and the transition from the large grain of small lamellae to the small grain of large lamellae. Four times of cyclic heat treatment refines the grain size from 1.33 mm to 0.59 turn, nevertheless the lamellar spacing increases from 0.71 ~tm to 1.38 lim. Extending the holding time and increasing the cyclic times of heat treatment eliminate the fl-segregation at the grain boundary and the interlamellar. The compression testing shows that the compressive strength of the directionally solidified ingot in the parallel and perpendicular directions are 1385.09 MPa and 1267.79 MPa, respectively, which are improved to 1449.75 MPa and 1527.76 MPa after two and four times of cyclic heat treatment, respectively, while that is 1180.64 MPa for the as-cast sample. The fracture mode of the sample after cyclic heat treatment is quasi-cleavage fracture.

Anisotropy of Thermal-expansion for β-Octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine： Quantum Chemistry Calculation and Molecular Dynamics Simulation

Molecular dynamics simulations on octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine （HMX） at 303-383 K and atmospheric pressure are carried out under NPT ensemble and COMPASS force field, the equilibrium structures at elevated temperatures were obtained and showed that the stacking style of molecules don＇t change. The coefficient of thermal expansion （CTE） values were calculated by linear fitting method. The results show that the CTE values are close to the experimental results and show anisotropy. The total energies of HMX cells with separately increasing expansion rates （100%-105%） along each crystallographic axis was calculated by periodic density functional theory method, the results of the energy change rates are anisotropic, and the correlation equations of energy change-CTE values are established. Thus the hypostasis of the anisotropy of HMX crystal＇s thermal expansion, the determinate molecular packing style, is elucidated.

SYNTHESIS AND CHARAOTERIZATION OF NOVEL THERMOTROPIO LIQUID ORYSTALLINE POLYESTERS BEARING NONLINEAR OPTICAL AZOBENZENE SIDE GROUP

A series of novel thermotropic liquid crystalline polyesters bearing nonlinear optical azobenzene side group were synthesized by high temperature solution polycondensation and their structures,thermal stability, phase transition behavior and crystallinity were characterized by IR,elemental analysis, TG-DTA, polarizing optical microscope (POM) equipped with a hot stage and X-ray diffraction techniques. The results demonstrate that all the synthesized polyesters exhibit nematic liquid crystalline phases and show relatively high glass transition temperatures and good thermal stability.

Mechanical properties and energy absorption properties of aluminum foam-filled square tubes

Longitudinal and transverse mechanical properties and energy absorption properties of foam-filled square tubes under quasi-static loading conditions were studied.The foam-filled thin-walled square tube was fabricated with aluminum tube as its shell and closed-cell Al-Mg alloy foam as its core.The results indicated that the plateau region of the load-displacement curve exhibited a marked fluctuant serration which was clearly related to the formation of folds.The longitudinal deforming mode of foam-filled square tube was the same as that of the empty tube,but the fold number of foam-filled square tube was more than that of the empty tube.The longitudinal compression load and energy absorption value of foam-filled square tube were higher than the sum of that of aluminum foam (alone) and empty tube (alone) due to the interaction between tube and filler.In transverse direction,the compression load and energy absorption ability of foam-filled square tubes were significantly lower than those in longitudinal direction.

Application of NIR spectroscopy for firmness evaluation of peaches

The use of near infrared （NIR） spectroscopy was proved to be a useful tool for quality analysis of fruits. A bifurcated fiber type NIR spectrometer, with a detection range of 800-2500 nm by InGaAs detector, was used to evaluate the firmness of peaches. Anisotropy of NIR spectra and firmness of peaches in relation to detecting positions of different parts （including three latitudes and three longitudes） were investigated. Both spectra absorbency and firmness of peach were influenced by longitudes （i, ii, iii） and latitudes （A, B, C）. For modeling, two thirds of the samples were used as the calibration set and the remaining one third were used as the validation or prediction set. Partial least square regression （PLSR） models for different longitude and latitude spectra and for the whole fruit show that collecting several NIR spectra from different longitudes and latitudes of a fruit for NIR calibration modeling can improve the modeling performance. In addition, proper spectra pretreatments like scattering correction or derivative also can enhance the modeling performance. The best results obtained in this study were from the holistic model with multiplicative scattering correction （MSC） pretreatment, with correlation coefficient of cross-validation γcv=0.864, root mean square error of cross-validation RMSECV=6.71 N, correlation coefficient of calibration r=0.948, root mean square error of calibration RMSEC=4.21 N and root mean square error of prediction RMSEP=5.42 N. The results of this study are useful for further research and application that when applying NIR spectroscopy for objectives with anisotropic differences, spectra and quality indices are necessarily measured from several parts of each object to improve the modeling performance.

Impact of anisotropic growth on kinetics of solid-state phase transformation

Based on the statistical analysis of blocking effect arising from anisotropic growth,the anisotropic effect on the kinetics of solid-state transformation was investigated.The result shows that the blocking effect leads to the retardation of transformation and then a regular behavior of varying Avrami exponent.Following previous analytical model,the formulations of Avrami exponent and effective activation energy accounting for blocking effect were obtained.The anisotropic effect on the transformation depends on two factors,non-blocking factor γ and blocking scale k,which directly acts on the dimensionality of growth.The effective activation energy is not affected by the anisotropic effect.The evolution of anisotropic effect with the fraction transformed is taken into account,showing that the anisotropic effect is more severe at the middle stage of transformation.

Targeted design of advanced electrocatalysts by machine learning

Exploring the production and application of clean energy has always been the core of sustainable development.As a clean and sustainable technology,electrocatalysis has been receiving widespread attention.It is crucial to achieve efficient,stable and cheap electrocatalysts.However,the traditional“trial and error”method is time-consuming,laborious and costly.In recent years,with the significant increase in computing power,computations have played an important role in electrocatalyst design.Nevertheless,it is still difficult to search for advanced electrocatalysts in the vast chemical space through traditional density functional theory(DFT)computations.Fortunately,the development of machine learning and interdisciplinary integration will inject new impetus into targeted design of electrocatalysts.Machine learning is able to predict electrochemical performances with an accuracy close to DFT.Here we provide an overview of the application of machine learning in electrocatalyst design,including the prediction of structure,thermodynamic properties and kinetic barriers.We also discuss the potential of explicit solvent model combined with machine learning molecular dynamics in this field.Finally,the favorable circumstances and challenges are outlined for the future development of machine learning in electrocatalysis.The studies on electrochemical processes by machine learning will further realize targeted design of high-efficiency electrocatalysts.

Effect of knurling shoulder design with polygonal pins on material flow and mechanical properties during friction stir welding of Al-Mg-Si alloy

Understanding the material flow facilitated by tool geometry in friction stir welds is challenging for quality weld production in industrial applications.The optimal tool shoulder and pin design combination,which plays a vital role in material flow was addressed.The flow of plasticized material was analyzed using a marker insert technique.The results show that the knurling shoulder design with square and hexagonal pin design facilitated constant stability force with reference to weld length/time.The uniform mixing and distribution of plasticized material were facilitated by the knurling shoulder design with square tool pin shape(TK)S(sticking length minimum)below which fragmented copper was observed.(TK)S tool facilitated higher mechanical properties for the welds,i.e.strength(182 MPa)and hardness(HV 78)in stir zone.

Microstructure and mechanical properties of TiC nanoparticle-reinforced Mg−Zn−Ca matrix nanocomposites processed by combining multidirectional forging and extrusion

TiC nanoparticle-reinforced Mg−4Zn−0.5Ca matrix nanocomposites were processed by combining multidirectional forging(MDF)and extrusion(EX).The grain size of the nanocomposite after MDF+EX multi-step deformation was significantly decreased compared with that processed only by MDF.The average size of the recrystallized grains gradually increased after EX with increasing the number of MDF passes at 270℃.However,the grain size significantly decreased by MDF processing at 310℃.Both fine and coarse MgZn2 phases appeared in the(MDF+EX)-processed nanocomposites,and their volume fractions gradually increased with increasing the number of MDF passes before EX.Ultrahigh tensile properties(yield strength of^404 MPa,ultimate tensile strength of^450.3 MPa and elongation of^5.2%)were obtained in the nanocomposite after three MDF passes at 310℃ followed by EX.This was attributed to the refinement of the recrystallized grains,together with the improved Orowan strengthening provided by the precipitated MgZn2 particles that were generated by MDF+EX multi-step deformation.