Based on the results of field trials and soil and plant measurements, the available silicon contents ofpaddy soils, their relations with the SiO_2 content of rice plant, the relationships between rice yield on theone ...Based on the results of field trials and soil and plant measurements, the available silicon contents ofpaddy soils, their relations with the SiO_2 content of rice plant, the relationships between rice yield on theone hand and the SiO_2 content and SiO_2/N ratio of rice plant on the other, the effects of silicon on riceyield and resistance to diseases and pests and the effective conditions and causes for increasing rice yield inSichuan Basin are expounded in the present paper. The study results show that about one half of the paddysoils developed from yellow soil, purple soil, alluvial soil, etc. in Sichuan Province were insufficient in siliconsupply. Critical values for silicon fertilization were 98 mg kg￣(-1) available Si in the paddy soils and < 112.8gkg￣(-1) SiO_2 in the rice plants. A SiO_2 content of rice plant over 121.6g kg￣(-1) and a SiO_2/N ratio maintainedat about 12 were required for gaining a rice yield of 7500 kg ha￣(-1). The yield increase by silicon fertilizationwas due to the improvement of silicon nutrition in rice plants and the balance of SiO_2/N ratio, and the reasonfor enhanced resistance to diseases and pests was concerned with the inhibition of luxury N absorption andthe raising of plant SiO_2/N ratio. Silicon fertilization tended to balance the uptake of N, P and K by riceplant .展开更多
Nutrition management is the most important for high yield production but it may affect the response of rice plants to pest and diseases due to the change of microclimate under rice plant canopy. The knowledge of nutri...Nutrition management is the most important for high yield production but it may affect the response of rice plants to pest and diseases due to the change of microclimate under rice plant canopy. The knowledge of nutrition management and its relation with pest and diseases are basis for setting up a high yield production system. Most of the pest and disease control procedures used by farmers can be considered as soil fertility management and these nutrition practices can have impact on the physiological susceptibility of crop plants to pest and diseases by affecting the plant resistance. Silicon content of plants is particularly effective against pest and diseases in rice and certain rice genotypes are more efficient accumulators of silicon, thus making them more resistant. In the absence of natural heritable resistance in rice varieties, resistance could be induced by altemate strategies to suppress certain pest and pathogens. Hence experiments were carried out in two stages during kharif 2010 and 2011 to assess the concentration of silicon in the index leaves of rice plant utilizing 133 varieties in four locations. The silica content of promising varieties ranged from 1.50% to 3.20%, 1.60% to 3.15%, 1.49% to 3.20% and 1.55% to 3.06% with a mean values of 2.50%, 2.48%, 2.51% and 2.43% at Jagtial, Warangal, Rajendranagar and Rudrur centres of Telangana region and not much variation in mean silica content in index leaves at different places. The overall yield from four locations ranged from 2,653 kg/ha to 6,860 kg/ha with a mean of 5,624 kg/ha. The yields recorded at Jagtial, Warangal, Rajendranagar and Rudrur centres ranged from 2,886 to 7,198, 2,653 to 6,831, 2,653 to 6,860 and 4,399 to 5,950 kg/ha, respectively. The lowest mean yield 5,069 kg/ha was noticed at Rudrur and the highest yield 5,940 kg/ha was found at Warangal. The variations in yields might be due to genotypic variations and also due to variations in climatic conditions of different locations.展开更多
The effects of aggressive peat nature (pH) on the strength of peat treated by cement and cement-sodium silicate grout were investigated by evaluating the changes in unconfined compressive strength,moisture content,and...The effects of aggressive peat nature (pH) on the strength of peat treated by cement and cement-sodium silicate grout were investigated by evaluating the changes in unconfined compressive strength,moisture content,and scanning electron microscopy (SEM) of samples with time in different pH media.The results indicate that peats treated by cement-silicate have higher strength than peats treated by cement,due to an increase in pH value of the media.Furthermore,cement and cement-silicate are highly effective in reducing the moisture content and void ratio of the treated peats.The microstructures of treated peats support the laboratory test results.展开更多
Due to the shortages of natural sands along the east coast of Australia in particular and the need to fully utilise fines produced in quarry operations, progress has been made in utilising blends of manufactured sands...Due to the shortages of natural sands along the east coast of Australia in particular and the need to fully utilise fines produced in quarry operations, progress has been made in utilising blends of manufactured sands and natural sands in concrete pavements. This paper documents some of the constraints in utilising larger proportions of manufactured sands in concrete pavements. These constraints are mainly caused by the current level of knowledge regarding the impact of manufactured sands on skid and abrasion resistance of concrete pavements. This paper presents a brief review of literature on this subject in the USA, France and UK. It also briefly documents work recently carried out in Australia by CCAA （Cement Concrete and Aggregates Australia）, referring to the skid and abrasion resistance of concrete pavements using manufactured sands. The paper concludes that there is no relationship between the free silica content and the skid resistance. With regard to the abrasion resistance, it is rather the curing conditions and the compressive strength that are more important in achieving good results.展开更多
Cement improves properties of soil materials, such as durability, stiffness, strength and moisture susceptibility. Each of them needs different cement contents that might not be suitable for other properties. Typicall...Cement improves properties of soil materials, such as durability, stiffness, strength and moisture susceptibility. Each of them needs different cement contents that might not be suitable for other properties. Typically, high cement content is desirable for durability, but not for shrinkage and cracking issues on the surface. Thus, improving durability with low cement content while complying with other requirements is an ideal aim, which may be achieved by pozzolanic supplementary products. Pozzolans contribute in hydration reactions and optimise cement consumptions in favour of durable and low shrinkage products. In this paper, the mixes of nano-silica and fly ash are considered to investigate their effect on strength, durability and shrinkage of modified CRB （crushed rock base） material. In the end, the benefits and features of nano-silica as a pozzolanic material will be focused and discussed more for effective cement consumption in soils.展开更多
Emission of carbon dioxide is considered to be the main cause of the greenhouse effect. Mineral carbonation, an important part of the CCS technology, is an attractive option for long-term CO2 sequestration. In this st...Emission of carbon dioxide is considered to be the main cause of the greenhouse effect. Mineral carbonation, an important part of the CCS technology, is an attractive option for long-term CO2 sequestration. In this study, wollastonite was chosen as the feedstock and the feasibility of direct aqueous mineral carbonation in the simulated flue gas was investigated via a series of experimental studies carried in a stirred reactor. X-ray diffraction （XRD）, X-ray fluorescence spectroscopy （XRF）, ion chro- matography （IC） and thermal decomposition were used to determine the carbonation conversion. The influences of various factors, including reaction temperature, reaction pressure, solution composition, heat-treatment and particle size, were dis- cussed. Concurrently, the effects of SO2 and NO presented in simulated flue gas were also investigated and a possible mecha- nism was used to explain the results. Experimental results show that reaction temperature, reaction pressure and particle size can effectively improve the carbonation reaction. Addition of 0.6 M NaHCO3 was also proved to be beneficial to the reaction and heat-treatment is not needed for wollastonite to get a higher carbonation conversion. Compared with carbonation in puri- fied CO2 gas, CO2 sequestration directly from simulated flue gas by mineral carbonation is suggested to have a certain degree of economic feasibility in the conditions of medium and low-pressure. A highest carbonation conversion of 35.9% is gained on the condition of T=150℃, P=40 bar and PS 〈30 μ in distilled water for 1 h.展开更多
文摘Based on the results of field trials and soil and plant measurements, the available silicon contents ofpaddy soils, their relations with the SiO_2 content of rice plant, the relationships between rice yield on theone hand and the SiO_2 content and SiO_2/N ratio of rice plant on the other, the effects of silicon on riceyield and resistance to diseases and pests and the effective conditions and causes for increasing rice yield inSichuan Basin are expounded in the present paper. The study results show that about one half of the paddysoils developed from yellow soil, purple soil, alluvial soil, etc. in Sichuan Province were insufficient in siliconsupply. Critical values for silicon fertilization were 98 mg kg￣(-1) available Si in the paddy soils and < 112.8gkg￣(-1) SiO_2 in the rice plants. A SiO_2 content of rice plant over 121.6g kg￣(-1) and a SiO_2/N ratio maintainedat about 12 were required for gaining a rice yield of 7500 kg ha￣(-1). The yield increase by silicon fertilizationwas due to the improvement of silicon nutrition in rice plants and the balance of SiO_2/N ratio, and the reasonfor enhanced resistance to diseases and pests was concerned with the inhibition of luxury N absorption andthe raising of plant SiO_2/N ratio. Silicon fertilization tended to balance the uptake of N, P and K by riceplant .
文摘Nutrition management is the most important for high yield production but it may affect the response of rice plants to pest and diseases due to the change of microclimate under rice plant canopy. The knowledge of nutrition management and its relation with pest and diseases are basis for setting up a high yield production system. Most of the pest and disease control procedures used by farmers can be considered as soil fertility management and these nutrition practices can have impact on the physiological susceptibility of crop plants to pest and diseases by affecting the plant resistance. Silicon content of plants is particularly effective against pest and diseases in rice and certain rice genotypes are more efficient accumulators of silicon, thus making them more resistant. In the absence of natural heritable resistance in rice varieties, resistance could be induced by altemate strategies to suppress certain pest and pathogens. Hence experiments were carried out in two stages during kharif 2010 and 2011 to assess the concentration of silicon in the index leaves of rice plant utilizing 133 varieties in four locations. The silica content of promising varieties ranged from 1.50% to 3.20%, 1.60% to 3.15%, 1.49% to 3.20% and 1.55% to 3.06% with a mean values of 2.50%, 2.48%, 2.51% and 2.43% at Jagtial, Warangal, Rajendranagar and Rudrur centres of Telangana region and not much variation in mean silica content in index leaves at different places. The overall yield from four locations ranged from 2,653 kg/ha to 6,860 kg/ha with a mean of 5,624 kg/ha. The yields recorded at Jagtial, Warangal, Rajendranagar and Rudrur centres ranged from 2,886 to 7,198, 2,653 to 6,831, 2,653 to 6,860 and 4,399 to 5,950 kg/ha, respectively. The lowest mean yield 5,069 kg/ha was noticed at Rudrur and the highest yield 5,940 kg/ha was found at Warangal. The variations in yields might be due to genotypic variations and also due to variations in climatic conditions of different locations.
基金the Ministry of Science,Technology Innovation,Malaysia (Project No.03-01-04-SF0889) for the financial support of this research
文摘The effects of aggressive peat nature (pH) on the strength of peat treated by cement and cement-sodium silicate grout were investigated by evaluating the changes in unconfined compressive strength,moisture content,and scanning electron microscopy (SEM) of samples with time in different pH media.The results indicate that peats treated by cement-silicate have higher strength than peats treated by cement,due to an increase in pH value of the media.Furthermore,cement and cement-silicate are highly effective in reducing the moisture content and void ratio of the treated peats.The microstructures of treated peats support the laboratory test results.
文摘Due to the shortages of natural sands along the east coast of Australia in particular and the need to fully utilise fines produced in quarry operations, progress has been made in utilising blends of manufactured sands and natural sands in concrete pavements. This paper documents some of the constraints in utilising larger proportions of manufactured sands in concrete pavements. These constraints are mainly caused by the current level of knowledge regarding the impact of manufactured sands on skid and abrasion resistance of concrete pavements. This paper presents a brief review of literature on this subject in the USA, France and UK. It also briefly documents work recently carried out in Australia by CCAA （Cement Concrete and Aggregates Australia）, referring to the skid and abrasion resistance of concrete pavements using manufactured sands. The paper concludes that there is no relationship between the free silica content and the skid resistance. With regard to the abrasion resistance, it is rather the curing conditions and the compressive strength that are more important in achieving good results.
文摘Cement improves properties of soil materials, such as durability, stiffness, strength and moisture susceptibility. Each of them needs different cement contents that might not be suitable for other properties. Typically, high cement content is desirable for durability, but not for shrinkage and cracking issues on the surface. Thus, improving durability with low cement content while complying with other requirements is an ideal aim, which may be achieved by pozzolanic supplementary products. Pozzolans contribute in hydration reactions and optimise cement consumptions in favour of durable and low shrinkage products. In this paper, the mixes of nano-silica and fly ash are considered to investigate their effect on strength, durability and shrinkage of modified CRB （crushed rock base） material. In the end, the benefits and features of nano-silica as a pozzolanic material will be focused and discussed more for effective cement consumption in soils.
基金supported by the National Natural Science Foundation of China (Grant Nos. 40972102, 41172140)the National Basic Research Program of China ("973" Project) (Grant No. 2011CB201500)
文摘Emission of carbon dioxide is considered to be the main cause of the greenhouse effect. Mineral carbonation, an important part of the CCS technology, is an attractive option for long-term CO2 sequestration. In this study, wollastonite was chosen as the feedstock and the feasibility of direct aqueous mineral carbonation in the simulated flue gas was investigated via a series of experimental studies carried in a stirred reactor. X-ray diffraction （XRD）, X-ray fluorescence spectroscopy （XRF）, ion chro- matography （IC） and thermal decomposition were used to determine the carbonation conversion. The influences of various factors, including reaction temperature, reaction pressure, solution composition, heat-treatment and particle size, were dis- cussed. Concurrently, the effects of SO2 and NO presented in simulated flue gas were also investigated and a possible mecha- nism was used to explain the results. Experimental results show that reaction temperature, reaction pressure and particle size can effectively improve the carbonation reaction. Addition of 0.6 M NaHCO3 was also proved to be beneficial to the reaction and heat-treatment is not needed for wollastonite to get a higher carbonation conversion. Compared with carbonation in puri- fied CO2 gas, CO2 sequestration directly from simulated flue gas by mineral carbonation is suggested to have a certain degree of economic feasibility in the conditions of medium and low-pressure. A highest carbonation conversion of 35.9% is gained on the condition of T=150℃, P=40 bar and PS 〈30 μ in distilled water for 1 h.
