To downsize and lighten automatic transmission components, the gears installed must be strengthened in terms of pitting endurance and/or wear resistance. The most important metallurgical factor affecting fractures is ...To downsize and lighten automatic transmission components, the gears installed must be strengthened in terms of pitting endurance and/or wear resistance. The most important metallurgical factor affecting fractures is well known to be resistance to softening when steel is tempered at approximately 573 K. Carbonitriding with a high amount of nitrogen is a very effective production technique because nitrogen increases the resistance during tempering. However, structural anomalies begin to appear in the surface layer when the nitrogen content exceeds 0.6 mass% in the chromium steel generally used. To address this, we have developed new high-strength chromium steel with an optimized chemical composition that effectively inhibits anomalies even when Carbonitriding with a nitrogen content of more than 0.6 mass%. We performed a drivetrain durability test on an automatic transmission component designed to have excellent contact fatigue strength and a tooth root bending impact and fatigue strength. We found that the developed steel that was carbonitrided with a content of about 0.9 mass%, and then shot peened hard, has a pitting life of roughly 4.5 times that of conventionally manufactured steel.展开更多
The changes of the substructure, the residual stress and the surface roughness of shot peened pure titanium were analyzed by means of SEM, TEM, XRD and surface roughness measurements in this paper. The results show th...The changes of the substructure, the residual stress and the surface roughness of shot peened pure titanium were analyzed by means of SEM, TEM, XRD and surface roughness measurements in this paper. The results show that shot peening increased the fatigue strength of pure titanium. The substructures of shot peened pure titanium consist of dislocations, deformation twins and deformation bands. Fatigue loading will relax the compressive residual stress and decrease the strengthening effect. The increased surface roughness has negative effects.展开更多
Nowadays, in the auto industry, the need for improvement of fuel efficiency is getting increased more and more in terms of the global warming, as well as the need of light-weighting of gears, transmission parts. Hence...Nowadays, in the auto industry, the need for improvement of fuel efficiency is getting increased more and more in terms of the global warming, as well as the need of light-weighting of gears, transmission parts. Hence, we’ve studied the relation between the shot peening working conditions and factors for improvement of gear’s fatigue life, and also the relation between the factors for improvement and the fatigue life, applying shot peening to a gear of SNCM220. Also, we examined the relation between the fatigue life and arc height that is utilized as a substitute characteristic for shot peening working conditions, adding its observation here.展开更多
Finite element method(FEM) was used to simulate the forming process of shotpeening the wing skin panel. Experiment of shotpeeing the wing skin panel was carried out. The results show that equivalent deformation in sho...Finite element method(FEM) was used to simulate the forming process of shotpeening the wing skin panel. Experiment of shotpeeing the wing skin panel was carried out. The results show that equivalent deformation in shotpeening process can be obtained using the elongation and bending result caused by thermal stress that is induced by applying temperature load on the surface of the part. Deformation of the part in the shotpeeing process can be analyzed using this method. The parameters and their relationships are identified.展开更多
文摘To downsize and lighten automatic transmission components, the gears installed must be strengthened in terms of pitting endurance and/or wear resistance. The most important metallurgical factor affecting fractures is well known to be resistance to softening when steel is tempered at approximately 573 K. Carbonitriding with a high amount of nitrogen is a very effective production technique because nitrogen increases the resistance during tempering. However, structural anomalies begin to appear in the surface layer when the nitrogen content exceeds 0.6 mass% in the chromium steel generally used. To address this, we have developed new high-strength chromium steel with an optimized chemical composition that effectively inhibits anomalies even when Carbonitriding with a nitrogen content of more than 0.6 mass%. We performed a drivetrain durability test on an automatic transmission component designed to have excellent contact fatigue strength and a tooth root bending impact and fatigue strength. We found that the developed steel that was carbonitrided with a content of about 0.9 mass%, and then shot peened hard, has a pitting life of roughly 4.5 times that of conventionally manufactured steel.
文摘The changes of the substructure, the residual stress and the surface roughness of shot peened pure titanium were analyzed by means of SEM, TEM, XRD and surface roughness measurements in this paper. The results show that shot peening increased the fatigue strength of pure titanium. The substructures of shot peened pure titanium consist of dislocations, deformation twins and deformation bands. Fatigue loading will relax the compressive residual stress and decrease the strengthening effect. The increased surface roughness has negative effects.
文摘Nowadays, in the auto industry, the need for improvement of fuel efficiency is getting increased more and more in terms of the global warming, as well as the need of light-weighting of gears, transmission parts. Hence, we’ve studied the relation between the shot peening working conditions and factors for improvement of gear’s fatigue life, and also the relation between the factors for improvement and the fatigue life, applying shot peening to a gear of SNCM220. Also, we examined the relation between the fatigue life and arc height that is utilized as a substitute characteristic for shot peening working conditions, adding its observation here.
文摘Finite element method(FEM) was used to simulate the forming process of shotpeening the wing skin panel. Experiment of shotpeeing the wing skin panel was carried out. The results show that equivalent deformation in shotpeening process can be obtained using the elongation and bending result caused by thermal stress that is induced by applying temperature load on the surface of the part. Deformation of the part in the shotpeeing process can be analyzed using this method. The parameters and their relationships are identified.
