A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment.The accuracy of the model is validated through comparison with e...A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment.The accuracy of the model is validated through comparison with experimental data.The influence of pre-injection control parameters on main-injection quantity under different control modes is analyzed.In the spill control valve mode,main-injection fuel quantity decreases gradually and then reaches a stable level because of the increase in multi-injection dwell time.In the needle control valve mode,main-injection fuel quantity increases with rising multi-injection dwell time;this effect becomes more obvious at high-speed revolutions and large main-injection pulse widths.Pre-injection pulse width has no obvious influence on main-injection quantity under the two control modes;the variation in main-injection quantity is in the range of 1 mm3.展开更多
A pintle injector is advantageous for throttling a liquid rocket engine and reducing engine weight. This study ex- plores the effects of momentum ratio and Weber number at various injection conditions on spray charact...A pintle injector is advantageous for throttling a liquid rocket engine and reducing engine weight. This study ex- plores the effects of momentum ratio and Weber number at various injection conditions on spray characteristics of the pintle injector for liquid-gas propellants. A liquid sheet is injected from a center pintle nozzle and it is broken by a gas jet from an annular gap. The pressure drops of propellants, and the pintle opening distance were consi- dered as control variables; using 0.1 -1.0 as a bar for the pressure drop of the liquid injection, a 0.01-4）.2 bar for the pressure drop of gas jet and a 0.2 - 1.0 mm for the pintle opening distance. The discharge coefficient was de- creased linearly before the pintle opening distance of 0.75 mm and then, the coefficient was slightly increased. Spray images were captured by a CMOS camera with high resolution. Then, the shadow and reflected images were analyzed. Spray distributions were measured by a pattemator with an axial distance of 50 mm from a pintle tip. Finally, the spray half angles had an exponentially decreasing correlation as a momentum ratio divided by the Weber number. Also, the spray half angles from the spray distribution were underestimated compared to those measured from the captured images.展开更多
基金Supported by the Program for New Century Excellent Talents in University（NECT-11-0826） the National Natural Science Foundation of China（NSFC 51279037）+1 种基金 the Fundamental Research Funds for the Central Universities（HEUCFZ13） the Postdoctoral Science-research Developmental Foundation of Heilongjiang Province（LBH-Q12126）Acknowledgement The authors gratefully acknowledge vice Professor Yong Shi and Jun Sun＇s help in fuel injection experiment.
文摘A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment.The accuracy of the model is validated through comparison with experimental data.The influence of pre-injection control parameters on main-injection quantity under different control modes is analyzed.In the spill control valve mode,main-injection fuel quantity decreases gradually and then reaches a stable level because of the increase in multi-injection dwell time.In the needle control valve mode,main-injection fuel quantity increases with rising multi-injection dwell time;this effect becomes more obvious at high-speed revolutions and large main-injection pulse widths.Pre-injection pulse width has no obvious influence on main-injection quantity under the two control modes;the variation in main-injection quantity is in the range of 1 mm3.
基金supported by Advanced Research Center Program(NRF-2013R1A5A1073861)through the National Research Foundation of Korea(NRF)grant funded by the Korea government(MSIP)contracted through Advanced Space Propulsion Research Center at Seoul National University
文摘A pintle injector is advantageous for throttling a liquid rocket engine and reducing engine weight. This study ex- plores the effects of momentum ratio and Weber number at various injection conditions on spray characteristics of the pintle injector for liquid-gas propellants. A liquid sheet is injected from a center pintle nozzle and it is broken by a gas jet from an annular gap. The pressure drops of propellants, and the pintle opening distance were consi- dered as control variables; using 0.1 -1.0 as a bar for the pressure drop of the liquid injection, a 0.01-4）.2 bar for the pressure drop of gas jet and a 0.2 - 1.0 mm for the pintle opening distance. The discharge coefficient was de- creased linearly before the pintle opening distance of 0.75 mm and then, the coefficient was slightly increased. Spray images were captured by a CMOS camera with high resolution. Then, the shadow and reflected images were analyzed. Spray distributions were measured by a pattemator with an axial distance of 50 mm from a pintle tip. Finally, the spray half angles had an exponentially decreasing correlation as a momentum ratio divided by the Weber number. Also, the spray half angles from the spray distribution were underestimated compared to those measured from the captured images.
