吸引器污染的调查

目的 对吸引器采样培养 ,了解吸引器的污染情况。方法 无菌盐水拭子涂抹瓶塞 (盖 )及出入口内表面培养分离细菌。结果 大多数吸引器被污染 ,污染菌主要为铜绿假单胞菌。结论 吸引器污染是医院感染潜在的不可忽视的危险因素 ,加强吸引器的管理 ,对预防医院感染有重要意义。

民用建筑室内环境污染物检测采样器性能测试比较

为选择适合室内环境检测用的大气采样器,考察了几种常用采样器的主要性能指标。比较它们的流量重复性、稳定性及示值偏差和抗负载能力。结果表明,恒流采样器采样更方便准确,并对恒流采样器的性能提出了一些要求。

空气净化器,成了污染器

近年来,由于居室的环境污染而导致的健康问题日益突出,于是空气净化器在人们对健康的盼望中出现。然而出人意料的是,空气净化器销量正呈下降趋势。目前的家电市场上,主要有过滤式、电子集尘式、臭氧和负氧离子四种类型的空气净化器。大多数消费者在购买此类产品之前,只是知道该产品的用途。

当心茶叶被铅污染

最近,因工作上的需要,我们对两家茶厂的6种茶叶,做了抽样检验。检验结果令我们惊讶,6种茶叶都检出铅!每公斤茶叶中铅的检出量为2.5～15.8毫克。我们用沸水泡茶叶后发现,冲泡5分钟时茶叶的铅检出率为零,冲泡10分钟和20分钟后都检出铅。

浅谈医院建筑防止水质污染措施

结合《建筑给水排水设计规范》,就南京某大型综合医院工程的给排水设计中有关防止水质污染问题的一些设计体验,从水源、给水系统、热水系统、生活给水管材等方面探讨了在医院建筑给排水设计中防止水质污染的一些措施。

Research on flue gas desulphurization with two sorbents by water spray in activated reactor

The experimental results of flue gas desulphurization with caustic lime andhydrated lime activated by water spraying in a desulphurization reactor are presented. The effectsof Ca/S molar ratio, approach to saturation of flue gas, SO_2 concentration and gas velocity onsulfur retention efficiency and calcium utilization rate are investigated. Desulphurizationcharacteristics of the two sorbents are compared. The mechanism of improving desulphurizationefficiency by water spraying is analyzed. The results show that the activities of two sorbents areimproved obviously by humidification with water spray and the caustic lime has better applicationprospect because of cheaper cost.

汽油添加剂：一种效应的研究

汽油添加剂：一种效应的研究Ｃ·Ｈ·ＪｅｗｅｎＧ＇Ｌ＇ＢｏｓｔｉｃｋＶ＇Ｌ＇Ｋｅｒｅｙ为了考察能够体现若干化学过程的汽油添加剂的性能，制订了一个综合试验方案，参照ＡＳＴＭＤ４３９要求对它们进行评价。各种测功计监控的汽车和固定式单缸、四缸和六缸发动机用来...

Removal of Di-n-butyl Phthalate Using Immobilized Microbial Cells

The biodegradation of di-n-butyl phthalate （DBP） using immobilized microbial cells was carded out in an internal airlift loop reactor with ceramic honeycomb supports. A strain that is capable of degrading DBP was isolated from the activated sludge and identified as Bacillus sp. using 16S rDNA sequential analysis. Bacillus sp. could be rapidly attached onto the ceramic honeycomb supports. The immobilized cells could effectively degrade DBP in batch and continuous experiments. When the influent concentration of DBP was 50mg·L^-1, the effluent DBP reached less than lmg.L i with 6h hydraulic retention time （HRT） in continuous experiment. The immobilized microbial cells could grow and accumulate through the biodegradation of DBP, and the rate of degradation is accordingly increased. The possible pathway of DBP biodegradation using immobilized cells was tentatively proposed.

Research progress on aging of organic pollutants in geosorbents:a review

Geosorbents are the main host of anthropogenic organic pollutants and play a vital role in their fate and transport in the natural environment.Soil and sediment are the most common and abundant geosorbents in the natural environment;their interactions with organic pollutants,especially sorption and desorption processes,have been extensively studied from the perspectives of thermodynamics and kinetics.Recently,the aging of organic pollutants in geosorbents has drawn increased attention,leading to an improved understanding of interactions between organic pollutants and geosorbents and informing remediation criteria.Aging has been deemed important in accurately assessing ecologic and health risks of organic pollutants,and both positive and negative impacts have been reported in studies of natural and artificial sorbents.This paper summarizes recent research progress on organic pollutant aging in geosorbents,including related mechanism research,influence factors,bioavailability assessments,and biological and physicochemical remediation of aged organic pollutants.We also discuss issues in the current research and bring forward suggestions for future study.

Preparation of Calcium Carbonate Nanoparticles with a Continuous Gas-liquid Membrane Contactor： Particles Morphology and Membrane Fouling

Nanosized calcium carbonate particles were prepared with a continuous gas-liquid membrane contactor. The effects of Ca(OH)2 concentration, CO2 pressure and liquid flow velocity on the particles morphology, pressure drop and membrane fouling were studied. With rising Ca(OH)2 concentrations, the average size of the particles increased. The effects of Ca(OH)2 concentration and CO2 pressure on particles were not apparent under the experimental conditions. When the Ca(OH)2 concentration and liquid flow velocity were high, or the CO2 pressure was low, the fouling on the membrane external surface at the contactor entrance was serious due to liquid leakage, whereas the fouling was slight at exit. The fouling on the membrane inner-surface at entrance was apparent due to adsorption of raw materials. The membrane can be recovered by washing with dilute hydrochloric acid and reused for at least 6 times without performance deterioration.

Changes in air pollutants during the COVID-19 lockdown in Beijing:Insights from a machine-learning technique and implications for future control policy

The COVID-19 lockdowns led to abrupt reductions in human-related emissions worldwide and had an unintended impact on air quality improvement.However,quantifying this impact is difficult as meteorological conditions may mask the real effect of changes in emissions on the observed concentrations of pollutants.Based on the air quality and meteorological data at 35 sites in Beijing from 2015 to 2020,a machine learning technique was applied to decouple the impacts of meteorology and emissions on the concentrations of air pollutants.The results showed that the real(“deweathered”)concentrations of air pollutants(expect for O 3)dropped significantly due to lockdown measures.Compared with the scenario without lockdowns(predicted concentrations),the observed values of PM_(2.5),PM_(10),SO_(2),NO_(2),and CO during lockdowns decreased by 39.4%,50.1%,51.8%,43.1%,and 35.1%,respectively.In addition,a significant decline for NO_(2)and CO was found at the background sites(51%and 37.8%)rather than the traffic sites(37.1%and 35.5%),which is different from the common belief.While the primary emissions reduced during the lockdown period,episodic haze events still occurred due to unfavorable meteorological conditions.Thus,developing an optimized strategy to tackle air pollution in Beijing is essential in the future.

Treatment of Benzene,Toluene and Xylene Contaminated Air in a Bioactive Foam Emulsion Reactor

A novel bioactive foam emulsion bioreactor for benzene,toluene and xylene(BTX)contaminated air streams treatment has been developed.The gas-liquid interfacial area by biocompatible foam and driving force for mass transfer by a water immiscible organic phase were increased in this reactor.The effect of several parameters such as gas residence time,oxygen content,and organic phase concentration on bioreactor performance was studied. Experimental results showed an average elimination capacity(EC)of 220 g·m3·h -1with removal efficiency(RE) of 89.59%for BTX inlet concentration of 1 g·m3at 15 s gas residence time in the bioreactor.The statistical developed model predicted that the maximum elimination capacity of the reactor for BTX could be reached to 423.45 g·m3·h -1.Continues operation of the bioreactor with high EC and RE was demonstrated by optimizing the operational parameters of the bioreactor.Overall the results suggest that the bioreactor developed can be very effective systems to treat BTX vapors.

Fouling Characteristics and Prevention Techniques for Membrane Bioreactor

Membrane fouling is the main problem of membrane bioreactors (MBR), which seriously influ- ences its wastewater treatment effect and running. The characteristics of microbiology and hydrodynamics concerning membrane fouling were investigated and the measure was put forward for optimum operation of MBR. The measure is that 1) the parameters of activated sludge concentration (X) and membrane flux should be lower than the critical values of X and membrane flux respectively, and 2) the activated sludge should be discharged periodically. The experimental results show that the combination backwashing of gas and perme- ated effluent is better than single gas backwashing or single permeated effluent backwashing. This technique can remove the cake layer deposited on the membrane surface, decrease the membrane fouling, and recover the membrane flux effectively. So it is effective for prevention of membrane fouling.

Optimized two-level placement of test points for multi-objective air monitoring of the Three Gorges Reservoir area

To fit the complicated geographic conditions of the Three Gorges Reservoir area, a two-level multi-objective monitoring system was developed to monitor the atmosphere of the area. Statistical analysis of environmental monitoring data and the macro control principle were employed to configure the upper layer. The lower layer was designed by the application of the thumb rule to a local terrain and specific point sources of pollution therein. The optimized two-level system comprises an upper layer of 16 monitoring stations distributed at places of diverse geographical, ecological, economical and social characteristics, and a lower layer of ]6 sub-machines at each monitoring station of the upper layer. This optimal outcome fits the complicated conditions of the Three Gorges Reservoir area, substantially cuts down the installation cost and the operation cost, and provides accurate monitoring data of atmosphere over the entire area with a high resolution.

Restaurant emissions removal by a biofilter with immobilized bacteria

Pseudomonas sp. ZD8 isolated from contaminated soil was immobilized with platane wood chips to produce packing materials for a novel biofilter system utilized to control restaurant emissions. The effects of operational parameters including retention time, temperature, and inlet gas concentration on the removal efficiency and elimination capacity were evaluated. Cri- teria necessary for a scale-up design of the biofilter was established. High and satisfactory level of rapeseed oil smoke removal efficiency was maintained during operation and the optimal retention time was found to be 18 s corresponding to smoke removal efficiency greater than 97%. The optimal inlet rapeseed oil smoke loading was 120 mg/(m3?h) at the upper end of the linear cor- relation between inlet loading and elimination capacity.

Rapid identification of single constant contaminant source by considering characteristics of real sensors

For the release of hazardous contaminant indoors, source identification is critical for developing effective response measures. A method which can quickly and accurately identify the position, emission rate, and release time of a single constant contaminant source by using real sensors was presented. The method was numerically demonstrated and validated by a case study of contaminant release in a three-dimensional office. The effects of the measurement errors and total sampling period of sensor on the performance of source identification were thoroughly studied. The results indicate that the adverse effects of the measurement errors can be mitigated by extending the total sampling period. For reaching a desirable accuracy of source identification, the total sampling period should exceed a certain threshold, which can be determined by repeatedly running the identification method tmtil the results tend to be stable. The method presented can contribute to develop an onsite source identification system for protecting occupants from indoor releases.

某溴化锂机组的故障分析

介绍了该机组出现的故障症状,分析了故障原因,总结了产生该故障最可能的几种原因。

Solar Oxidation and Removal of Arsenic from Groundwater Utilizing a Semicircular Section Tubular Photoreactor

A semicircular section tubular photoreactor has been constructed, characterized and applied to the treatment of groundwater contaminated with As（V） by means of the SORAS （solar oxidation and removal of arsenic） technique, using ferrous and citrate salts. The solar concentrator was built with recyclable waste materials： glass tubes from fluorescent lamps and 6-inch diameter PVC pipes cut in half and covered by aluminum foil. The reactor concentrates solar radiation up to 2.8 times its natural intensity. Batch irradiation experiments followed by controlled agitation （shear rate = 30-33 s^-1; 20 min agitation period） showed that the photoreactor accelerates the formation of settleable floccules （Dp 〉 0.5mm）, compared with a fluorescent lamp glass tube alone and a 2 L PET （polyethylene terephthalate） bottle. Irradiation times necessary for floccule formation in the photoreactor, the fluorescent lamp tube and the PET bottle were 15 min, 25 min and 60 min, respectively. Continuous flow experiments using a photoreactor with a photo-collection area of 0.9 m^2 and a hydraulic retention time （equal to the irradiation time） of 15 rain showed that immediate formation of floccules of good settleability occurs when the solution is subjected to moderate agitation （33 s^-1）. An efficiency of 98.36% for As（V） removal was obtained with a final concentration of 16.5 ktg/L in decanted waters. In accordance to these results, the photoreactor is able to treat approximately 130 L/m^2 within a 5-h period with UVA irradiation intensities of 50-70 W/mE.

A Novel 3-D Nano-assembly Bacteria Based Biosensor for Enhanced Detection of Heavy Metal Pollutants

Nowadays, at a time of growing concern for sustainable development and compliance with environmental standards and legislation, the detection of heavy metal contaminants in environmental matrices represents a difficult but important task. The current major limitation lies in the poor detection limits of the targeted pollutant＇s trace concentrations by the available conventional techniques. In order to elaborate a novel ＂living＂ self assembled electrochemical 3-D biosensor, the authors propose a new concept to overcome this shortcoming. The advantages of the properties of polyelectrolyte-functionalized NBs （nanobeads） are combined along with the use of non covalently strongly bound micro-organisms. The designed 3-D biosensor is all the more promising as it has showed a significantly improved sensitivity. In fact, the detection limits of the tested heavy metals （cadmium and mercury） were as low as 1.0 × 10^-12 mol.L-1 and six to seven orders of magnitude lower than those provided by conventional 2-D biosensors. Furthermore, it is potentially applicable to a wide range of bioreceptor-pollutant detection systems.

Effect of Chloride on the Atmospheric Corrosion of Cast Iron in Sulphur or Nitrogen-Bearing Pollutant Environment

The effect of chloride on the atmospheric corrosion of cast iron in sulphur or nitrogen-bearing pollutant was investigated by using periodic wet-dry test, electrochemical experiment and surface tension test. Scanning electron microscopy coupled with energy dispersive atomic （EDAX） and stereoscopic microscopy was used to identify the corrosion processes and products. Cl^- and NO3^- were shown accelerating effects during the whole corrosion process but depression effects were observed in Cl^- and HSO3^- bearing pollutant at the initial corrosion stage. However, with the corrosion going on, the depression effects was less obviously and the initial corrosion process was investigated from the viewpoint of surface activity. At the initial corrosion stage, the corrosion rate was proportional to the adsorptivity of anions, but as corrosion went on, the penetration effect of anions and different characteristics of the corrosion products began to dominate the corrosion process, which led to changes on the corrosion rate.