针对某航天电子管壳焊接组件冷却过程中的热力耦合影响问题,建立了焊接组件的有限元热分析模型,研究了在快速冷却过程中梯度材料分布对低温共烧陶瓷(low temperature co-fired ceramic,LTCC)基板、梯度管壳的残余应力和变形的影响。以...针对某航天电子管壳焊接组件冷却过程中的热力耦合影响问题,建立了焊接组件的有限元热分析模型,研究了在快速冷却过程中梯度材料分布对低温共烧陶瓷(low temperature co-fired ceramic,LTCC)基板、梯度管壳的残余应力和变形的影响。以不超过基板断裂强度为前提条件,以降低管壳整体的残余应力与变形为优化目标,采用了多因素变换优选法,确定了管壳材料的最优梯度分布方案,即合金管壳自上而下的梯度分布为Al-35Si、Al-42Si、Al-50Si、Al-60Si、Al-70Si。其中,Al-35Si厚度为2.5mm,Al-42Si与Al-60Si的厚度均为1.6mm,Al-50Si厚度为0.8mm,Al-70Si厚度为2mm。在该方案下,LTCC基板冷却至室温时的最大变形量为4.86μm,最大第一主应力为6761MPa,远小于LTCC材料的断裂强度320MPa;管壳冷却至室温时的最大变形量为18.291μm,最大残余应力值为20.46MPa,远小于管壳材料的屈服强度100MPa。管壳各层之间的应力集中现象不明显,管壳的整体焊接质量得到提升。展开更多
This paper analyses the changing rule of indoor ozone concentration and its influencing factors.A formula of indoor-outdoor concentration ratio(I/O ratio) was deduced based on the indoor ozone mass-balance equation.Th...This paper analyses the changing rule of indoor ozone concentration and its influencing factors.A formula of indoor-outdoor concentration ratio(I/O ratio) was deduced based on the indoor ozone mass-balance equation.The ozone I/O ratio in different kinds of buildings was studied.Results show that I/O ratio is much related to air-exchange rate,which is well compatible with the theoretical calculation results.展开更多
In this study, we investigate the fabrication of periodically poled lithium niobate(PPLN) microdisk cavities on a chip. These resonators are fabricated from a PPLN film with a 16 μm poling period on insulator using c...In this study, we investigate the fabrication of periodically poled lithium niobate(PPLN) microdisk cavities on a chip. These resonators are fabricated from a PPLN film with a 16 μm poling period on insulator using conventional microfabrication techniques.The quality factor of the PPLN microdisk resonators with a 40-μm radius and a 700-nm thickness is 6.7×10~5. Second harmonic generation(SHG) with an efficiency of 2.2×10^(-6) mW(-1) is demonstrated in the fabricated PPLN microdisks. The nonlinear conversion efficiency could be considerably enhanced by optimizing the period and pattern of the poled structure and by improving the cavity quality factors.展开更多
文摘针对某航天电子管壳焊接组件冷却过程中的热力耦合影响问题,建立了焊接组件的有限元热分析模型,研究了在快速冷却过程中梯度材料分布对低温共烧陶瓷(low temperature co-fired ceramic,LTCC)基板、梯度管壳的残余应力和变形的影响。以不超过基板断裂强度为前提条件,以降低管壳整体的残余应力与变形为优化目标,采用了多因素变换优选法,确定了管壳材料的最优梯度分布方案,即合金管壳自上而下的梯度分布为Al-35Si、Al-42Si、Al-50Si、Al-60Si、Al-70Si。其中,Al-35Si厚度为2.5mm,Al-42Si与Al-60Si的厚度均为1.6mm,Al-50Si厚度为0.8mm,Al-70Si厚度为2mm。在该方案下,LTCC基板冷却至室温时的最大变形量为4.86μm,最大第一主应力为6761MPa,远小于LTCC材料的断裂强度320MPa;管壳冷却至室温时的最大变形量为18.291μm,最大残余应力值为20.46MPa,远小于管壳材料的屈服强度100MPa。管壳各层之间的应力集中现象不明显,管壳的整体焊接质量得到提升。
文摘This paper analyses the changing rule of indoor ozone concentration and its influencing factors.A formula of indoor-outdoor concentration ratio(I/O ratio) was deduced based on the indoor ozone mass-balance equation.The ozone I/O ratio in different kinds of buildings was studied.Results show that I/O ratio is much related to air-exchange rate,which is well compatible with the theoretical calculation results.
基金supported by the National Natural Science Foundation of China(Grant Nos.11734009,11674181,11774182,and 11674184)the 111 Project(Grant No.B07013)+1 种基金PCSIRT(Grant No.IRT 13R29)CAS Interdisciplinary Innovation Team
文摘In this study, we investigate the fabrication of periodically poled lithium niobate(PPLN) microdisk cavities on a chip. These resonators are fabricated from a PPLN film with a 16 μm poling period on insulator using conventional microfabrication techniques.The quality factor of the PPLN microdisk resonators with a 40-μm radius and a 700-nm thickness is 6.7×10~5. Second harmonic generation(SHG) with an efficiency of 2.2×10^(-6) mW(-1) is demonstrated in the fabricated PPLN microdisks. The nonlinear conversion efficiency could be considerably enhanced by optimizing the period and pattern of the poled structure and by improving the cavity quality factors.
