For the production of low ash content clean coal, separation at low density is required for some raw coals.Based on analyzing the fluidizing characteristics of magnetic-pearls with a specific size clistribution and fo...For the production of low ash content clean coal, separation at low density is required for some raw coals.Based on analyzing the fluidizing characteristics of magnetic-pearls with a specific size clistribution and formation mechanism of a microbubble fluidized bed, optimal technological and operating parameters suitable for low density coal separation were determined. The experimental results show that an air dense medium fluidized bed with low den-sity can be formed using magnetic pearls as medium solids, which can efficiently beneficiate coal of 6-50 mm size with a probable error Ep value of 0.05 at a separating density of 1.44 g/cm^3.展开更多
The effect of sulfur compounds （including sulfur, sulfide, sulfite and sulfate）, initial concentration of heavy metal and operating conditions on Cd emission in municipal solid waste （MSW） incineration were invest...The effect of sulfur compounds （including sulfur, sulfide, sulfite and sulfate）, initial concentration of heavy metal and operating conditions on Cd emission in municipal solid waste （MSW） incineration were investi-gated using a simulated tubular furnace and simulated MSW spiked with Cd. The concentration of Cd was meas-ured by inductively coupled plasma-atomic emission spectrometry （ICP-AES） after digesting the samples including bottom ash, fly ash and flue gas according to related USEPA methods. The results show that S and Na2S tend to in- crease Cd partitioning in bottom ash, whereas Na2SO3 and Na2SO4 tend to reduce Cd partitioning in bottom ash. The effect of sulfur compounds on Cd partitioning in bottom ash was in the sequence of Na2S〉S〉Na2SO3〉 Na2SO4. chemical equilibrium analysis is also performed to determine the effect of sorbents on Cd adsorption. The calculations show that S presents strong affinity for Cd and restrains Cd adsorption by SiO2, whereas when temperature rises to between 830℃ and 1030℃, Cd adsorption efficiency of SiO2 is over 80% and the efficiency of Al2O3 is up to 85%.展开更多
Chemical-looping gasification （CLG） is a novel process for syngas generation from solid fuels, sharing the same basic principles as chemical-looping combustion （CLC）. It also uses oxygen carriers （mainly metal ox...Chemical-looping gasification （CLG） is a novel process for syngas generation from solid fuels, sharing the same basic principles as chemical-looping combustion （CLC）. It also uses oxygen carriers （mainly metal oxide and calcium sulfate） to transfer heat and oxygen to the fuel. In this paper, the primary investigation into the CLG process with CaSO4 as oxygen carrier was carried out by thermodynamic analysis and experiments in the tube reactor. Sulfur-contained gas emission was mainly H2S rather than SO2 in the CLG process, showing some different features from the CLC. The mass and heat balance of CLG processes were calculated thermodynamically to determinate the auto-thermal operating conditions with different CaSO4/C and steam/C molar ratios. It was found that the CaSO4/C molar ratio should be higher than 0.2 to reach auto-thermal balance. The effect of temperature on the reactions between oxygen carrier and coal was investigated based on Gibbs free energy minimum method and ex- perimental results. It indicated that high temperature favored the CLG process in the fuel reactor and part of syngas was consumed to compensate for auto-thermal system.展开更多
H2 is an important energy carrier for replacing fossil fuel in the future due to its high energy density and environmental friendliness.As a sustainable H2-generation method,photocatalytic H2 production by water split...H2 is an important energy carrier for replacing fossil fuel in the future due to its high energy density and environmental friendliness.As a sustainable H2-generation method,photocatalytic H2 production by water splitting has attracted much interest.Here,oil-soluble ZnxCd1-xS quantum dot(ZCS QD)with a uniform particle size distribution were prepared by a hot-injection method.However,no photocatalytic H2-production activity was observed for the oil-soluble ZCS QD due to its hydrophobicity.Thus,the oil-soluble ZCS QD was converted into a water-soluble ZCS QD by a ligand-exchange method.The water-soluble ZCS QD exhibited excellent photocatalytic H2-production performance in the presence of glycerin and Ni^2+,with an apparent quantum efficiency of 15.9%under irradiation of 420 nm light.Further,the photocatalytic H2-generation activity of the ZCS QD was~10.7 times higher than that of the ZnxCd1-xS relative samples prepared by the conventional co-precipitation method.This work will inspire the design and fabrication of other semiconductor QD photocatalysts because QD exhibits excellent separation efficiency for photogenerated electron-hole pairs due to its small crystallite size.展开更多
The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and Mo...The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and MoS2 on the properties of composites was analyzed through a comparative experiment by adding Ni and MoS2 separately.The results show that the nickel wrapping around the MoS2 particles decreases the reaction rate of MoS2 with the copper matrix,and greatly improves the bonding of the matrix.The composites with 12 wt.%Ni-coated MoS2(C12)show the optimum performance including the mechanical properties and tribological behaviors.Under oil lubrication conditions,the friction coefficient is 0.0075 with a pressure of 8 MPa and a linear velocity of 0.25 m/s.The average dry friction coefficient,sliding against 40Cr steel disc,is measured to be 0.1769 when the linear velocity and pressure are 0.25 m/s and 4 MPa,respectively.展开更多
基金Projects 90510002, 90210035 supported by the National Natural Science Foundation of China306008 by the Science and Technology Research of Ministry of Education of China
文摘For the production of low ash content clean coal, separation at low density is required for some raw coals.Based on analyzing the fluidizing characteristics of magnetic-pearls with a specific size clistribution and formation mechanism of a microbubble fluidized bed, optimal technological and operating parameters suitable for low density coal separation were determined. The experimental results show that an air dense medium fluidized bed with low den-sity can be formed using magnetic pearls as medium solids, which can efficiently beneficiate coal of 6-50 mm size with a probable error Ep value of 0.05 at a separating density of 1.44 g/cm^3.
文摘The effect of sulfur compounds （including sulfur, sulfide, sulfite and sulfate）, initial concentration of heavy metal and operating conditions on Cd emission in municipal solid waste （MSW） incineration were investi-gated using a simulated tubular furnace and simulated MSW spiked with Cd. The concentration of Cd was meas-ured by inductively coupled plasma-atomic emission spectrometry （ICP-AES） after digesting the samples including bottom ash, fly ash and flue gas according to related USEPA methods. The results show that S and Na2S tend to in- crease Cd partitioning in bottom ash, whereas Na2SO3 and Na2SO4 tend to reduce Cd partitioning in bottom ash. The effect of sulfur compounds on Cd partitioning in bottom ash was in the sequence of Na2S〉S〉Na2SO3〉 Na2SO4. chemical equilibrium analysis is also performed to determine the effect of sorbents on Cd adsorption. The calculations show that S presents strong affinity for Cd and restrains Cd adsorption by SiO2, whereas when temperature rises to between 830℃ and 1030℃, Cd adsorption efficiency of SiO2 is over 80% and the efficiency of Al2O3 is up to 85%.
基金Supported by the National~ Natural Science Foundation of China （20876079）, the Natural Science Funds for Distinguished Young Scholar in Shandong Province （JQ200904）, and Shandong Province Key Technologies Research and Development Program of China （2008GG 10006010, 2009GG 10007001）.
文摘Chemical-looping gasification （CLG） is a novel process for syngas generation from solid fuels, sharing the same basic principles as chemical-looping combustion （CLC）. It also uses oxygen carriers （mainly metal oxide and calcium sulfate） to transfer heat and oxygen to the fuel. In this paper, the primary investigation into the CLG process with CaSO4 as oxygen carrier was carried out by thermodynamic analysis and experiments in the tube reactor. Sulfur-contained gas emission was mainly H2S rather than SO2 in the CLG process, showing some different features from the CLC. The mass and heat balance of CLG processes were calculated thermodynamically to determinate the auto-thermal operating conditions with different CaSO4/C and steam/C molar ratios. It was found that the CaSO4/C molar ratio should be higher than 0.2 to reach auto-thermal balance. The effect of temperature on the reactions between oxygen carrier and coal was investigated based on Gibbs free energy minimum method and ex- perimental results. It indicated that high temperature favored the CLG process in the fuel reactor and part of syngas was consumed to compensate for auto-thermal system.
文摘H2 is an important energy carrier for replacing fossil fuel in the future due to its high energy density and environmental friendliness.As a sustainable H2-generation method,photocatalytic H2 production by water splitting has attracted much interest.Here,oil-soluble ZnxCd1-xS quantum dot(ZCS QD)with a uniform particle size distribution were prepared by a hot-injection method.However,no photocatalytic H2-production activity was observed for the oil-soluble ZCS QD due to its hydrophobicity.Thus,the oil-soluble ZCS QD was converted into a water-soluble ZCS QD by a ligand-exchange method.The water-soluble ZCS QD exhibited excellent photocatalytic H2-production performance in the presence of glycerin and Ni^2+,with an apparent quantum efficiency of 15.9%under irradiation of 420 nm light.Further,the photocatalytic H2-generation activity of the ZCS QD was~10.7 times higher than that of the ZnxCd1-xS relative samples prepared by the conventional co-precipitation method.This work will inspire the design and fabrication of other semiconductor QD photocatalysts because QD exhibits excellent separation efficiency for photogenerated electron-hole pairs due to its small crystallite size.
基金Projects(51371099,51501091)supported by the National Natural Science Foundation of China。
文摘The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and MoS2 on the properties of composites was analyzed through a comparative experiment by adding Ni and MoS2 separately.The results show that the nickel wrapping around the MoS2 particles decreases the reaction rate of MoS2 with the copper matrix,and greatly improves the bonding of the matrix.The composites with 12 wt.%Ni-coated MoS2(C12)show the optimum performance including the mechanical properties and tribological behaviors.Under oil lubrication conditions,the friction coefficient is 0.0075 with a pressure of 8 MPa and a linear velocity of 0.25 m/s.The average dry friction coefficient,sliding against 40Cr steel disc,is measured to be 0.1769 when the linear velocity and pressure are 0.25 m/s and 4 MPa,respectively.
