The overturning stability is vital for the retaining wall design of foundation pits, where the surrounding soils are usually unsaturated due to water draining. Moreover, the intermediate principal stress does affect t...The overturning stability is vital for the retaining wall design of foundation pits, where the surrounding soils are usually unsaturated due to water draining. Moreover, the intermediate principal stress does affect the unsaturated soil strength; meanwhile, the relationship between the unsaturated soil strength and matric suction is nonlinear. This work is to present closed-form equations of critical embedment depth for a rigid retaining wall against overturning by means of moment equilibrium. Matric suction is considered to be distributed uniformly and linearly with depth. The unified shear strength formulation for unsaturated soils under the plane strain condition is adopted to characterize the intermediate principal stress effect, and strength nonlinearity is described by a hyperbolic model of suction angle. The result obtained is orderly series solutions rather than one specific answer; thus, it has wide theoretical significance and good applicability. The validity of this present work is demonstrated by comparing it with a lower bound solution. The traditional overturning designs for rigid retaining walls, in which the saturated soil mechanics neglecting matric suction or the unsaturated soil mechanics based on the Mohr-Coulomb criterion are employed, are special cases of the proposed result. Parametric studies about the intermediate principal stress, matric suction and its distributions along with two strength nonlinearity methods on a new defined critical buried coefficient are discussed.展开更多
This study presents a laboratory investigation of load-settlement behaviour of a strip footing resting on iron ore tailings used as a structural fill.The footing was placed at various depths in the tailings bed.The re...This study presents a laboratory investigation of load-settlement behaviour of a strip footing resting on iron ore tailings used as a structural fill.The footing was placed at various depths in the tailings bed.The relative density of the tailings was varied as D_r = 50%,70%and 90%.An incremental load was applied on the footing while observing the settlement until the failure took place.The results obtained for tailings were compared with those for the sandy soil.It is observed that the load-bearing capacity and stiffness increase with an increase in footing embedment depth and relative density.Compared to load-settlement behaviour of Perth sandy soil,the tailings fill could have as high as 22 times and 13.5 times the load-bearing capacity and stiffness,respectively.Therefore,the replacement of sandy soil with iron ore tailings for structural fills is cost-effective,and moreover,this application contributes to environmental sustainability in construction.展开更多
The finite element method is used to simulate the rectification process of shield machine, to study the relationship between rectification moment and angle and to explore the influence laws of different soil parameter...The finite element method is used to simulate the rectification process of shield machine, to study the relationship between rectification moment and angle and to explore the influence laws of different soil parameters and buried depth on rectification moment. It is hoped that the reference value of rectification moment can be offered to operator, and theoretical foundation can be laid for future automatic rectification technology. The results show that the rectification moment and angle generally exhibit good linear behavior in clay layers with different soil parameters or buried depths, and then the concept of rectification coefficient, that is, the ratio of rectification angle to rectification moment, is proposed; different soil parameters and buried depths have different influences on rectification coefficient, in which elastic modulus has great influence but others have little influences; the simulations of rectification process are preformed in clay layers with different elastic modulus, and fitting results show that elastic modulus and rectification coefficient present the quadratic function relation.展开更多
基金Project(41202191)supported by the National Natural Science Foundation of ChinaProject(2015JM4146)supported by the Natural Science Foundation of Shaanxi Province,ChinaProject(2015)supported by the Postdoctoral Research Project of Shaanxi Province,China
文摘The overturning stability is vital for the retaining wall design of foundation pits, where the surrounding soils are usually unsaturated due to water draining. Moreover, the intermediate principal stress does affect the unsaturated soil strength; meanwhile, the relationship between the unsaturated soil strength and matric suction is nonlinear. This work is to present closed-form equations of critical embedment depth for a rigid retaining wall against overturning by means of moment equilibrium. Matric suction is considered to be distributed uniformly and linearly with depth. The unified shear strength formulation for unsaturated soils under the plane strain condition is adopted to characterize the intermediate principal stress effect, and strength nonlinearity is described by a hyperbolic model of suction angle. The result obtained is orderly series solutions rather than one specific answer; thus, it has wide theoretical significance and good applicability. The validity of this present work is demonstrated by comparing it with a lower bound solution. The traditional overturning designs for rigid retaining walls, in which the saturated soil mechanics neglecting matric suction or the unsaturated soil mechanics based on the Mohr-Coulomb criterion are employed, are special cases of the proposed result. Parametric studies about the intermediate principal stress, matric suction and its distributions along with two strength nonlinearity methods on a new defined critical buried coefficient are discussed.
文摘This study presents a laboratory investigation of load-settlement behaviour of a strip footing resting on iron ore tailings used as a structural fill.The footing was placed at various depths in the tailings bed.The relative density of the tailings was varied as D_r = 50%,70%and 90%.An incremental load was applied on the footing while observing the settlement until the failure took place.The results obtained for tailings were compared with those for the sandy soil.It is observed that the load-bearing capacity and stiffness increase with an increase in footing embedment depth and relative density.Compared to load-settlement behaviour of Perth sandy soil,the tailings fill could have as high as 22 times and 13.5 times the load-bearing capacity and stiffness,respectively.Therefore,the replacement of sandy soil with iron ore tailings for structural fills is cost-effective,and moreover,this application contributes to environmental sustainability in construction.
基金Project(2007CB714006)supported by the National Basic Research Program of China
文摘The finite element method is used to simulate the rectification process of shield machine, to study the relationship between rectification moment and angle and to explore the influence laws of different soil parameters and buried depth on rectification moment. It is hoped that the reference value of rectification moment can be offered to operator, and theoretical foundation can be laid for future automatic rectification technology. The results show that the rectification moment and angle generally exhibit good linear behavior in clay layers with different soil parameters or buried depths, and then the concept of rectification coefficient, that is, the ratio of rectification angle to rectification moment, is proposed; different soil parameters and buried depths have different influences on rectification coefficient, in which elastic modulus has great influence but others have little influences; the simulations of rectification process are preformed in clay layers with different elastic modulus, and fitting results show that elastic modulus and rectification coefficient present the quadratic function relation.
