The NiCoCrAl alloy sheet was fabricated by electron beam physical vapor deposition technique and the effects of the heat treatment on the microstructure and tensile strength of the NiCoCrAl alloy sheet were investigat...The NiCoCrAl alloy sheet was fabricated by electron beam physical vapor deposition technique and the effects of the heat treatment on the microstructure and tensile strength of the NiCoCrAl alloy sheet were investigated. The heat treatment at 1050 °C is favorable to improve the interface bonding between the columnar structures due to the disappearance of the intergranular gaps. Comparing with the thin NiCoCrAl alloy sheet before heat treatment, the Ni3Al phase appears in the NiCoCrAl alloy sheet after heat treatment, which is favorable to improve the interface bonding between the columnar structures. The increase in the tensile strength and elongation is attributed to the improvement of the interface bonding between the columnar structures. The residual stress in the NiCoCrAl alloy sheet after heat treatment is reduced significantly, which also confirms that the interface bonding is improved by the heat treatment.展开更多
In order to optimize the ductility of orthorhombic Ti2AlNb-based alloys sheet,Ti22Al27Nb sheet was treated by high density electropulsing（J max =6.80 7.09 kA/mm2,tp =110 μs） under ambient condition.Microstructures ...In order to optimize the ductility of orthorhombic Ti2AlNb-based alloys sheet,Ti22Al27Nb sheet was treated by high density electropulsing（J max =6.80 7.09 kA/mm2,tp =110 μs） under ambient condition.Microstructures were observed by SEM,and the tensile properties were also studied using uniaxial tension tests.The experimental results show that electropulsing can refine the microstructures of Ti22Al27Nb sheets.The specimen with the fine and homogeneous microstructures has good plasticity,and its elongation reaches 19.4%.The mechanism about the effect of electropulsing treatment on the microstructure of Ti22Al27Nb sheets was discussed.It was thought that the increase in nucleation rate during phase transformation and a very short treating time were regarded as the main reasons of producing smaller grains and increase in the plasticity by electropulsing.展开更多
Directionally solidified （DS） specimens of Nb-Ti-Si based ultrahigh temperature alloy were heat-treated at （1 500 ℃, 50 h） and （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, respectively. The results show that the mic...Directionally solidified （DS） specimens of Nb-Ti-Si based ultrahigh temperature alloy were heat-treated at （1 500 ℃, 50 h） and （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, respectively. The results show that the microstructures become uniform, the long and big primary （Nb,X）sSi3 （X represents Ti and Hf elements） plates in the DS specimens are broken into small ones, and the eutectic cells lose their lamellar morphology and their interfaces become blurry after heat-treatment. Meanwhile, the （Nb,X）sSi3 slices in the eutectic cells of the DS specimens coarsen obviously after heat-treatment. Homogenizing and aging treatments could effectively eliminate elemental microsegregation, and the segregation ratios of all elements in niobium solid solution （Nbss） in different regions tend to 1. After heat-treatment, the microhardness of retained eutectic cells increases evidently, and the maximum value reaches HV1 404.57 for the specimen directionally solidified with a withdrawing rate of 100 μm/s and then heat-treated at （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, which is 72.8 % higher than that under DS condition.展开更多
基金Projects(51002019,91016024,51102031)supported by the National Natural Science Foundation of China
文摘The NiCoCrAl alloy sheet was fabricated by electron beam physical vapor deposition technique and the effects of the heat treatment on the microstructure and tensile strength of the NiCoCrAl alloy sheet were investigated. The heat treatment at 1050 °C is favorable to improve the interface bonding between the columnar structures due to the disappearance of the intergranular gaps. Comparing with the thin NiCoCrAl alloy sheet before heat treatment, the Ni3Al phase appears in the NiCoCrAl alloy sheet after heat treatment, which is favorable to improve the interface bonding between the columnar structures. The increase in the tensile strength and elongation is attributed to the improvement of the interface bonding between the columnar structures. The residual stress in the NiCoCrAl alloy sheet after heat treatment is reduced significantly, which also confirms that the interface bonding is improved by the heat treatment.
基金Project(50875061) supported by the National Natural Science Foundation of ChinaProject(20092302110016) supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘In order to optimize the ductility of orthorhombic Ti2AlNb-based alloys sheet,Ti22Al27Nb sheet was treated by high density electropulsing（J max =6.80 7.09 kA/mm2,tp =110 μs） under ambient condition.Microstructures were observed by SEM,and the tensile properties were also studied using uniaxial tension tests.The experimental results show that electropulsing can refine the microstructures of Ti22Al27Nb sheets.The specimen with the fine and homogeneous microstructures has good plasticity,and its elongation reaches 19.4%.The mechanism about the effect of electropulsing treatment on the microstructure of Ti22Al27Nb sheets was discussed.It was thought that the increase in nucleation rate during phase transformation and a very short treating time were regarded as the main reasons of producing smaller grains and increase in the plasticity by electropulsing.
基金Project(51071124)supported by the National Natural Science Foundation of ChinaProject(CX200605)supported by the Doctorate Foundation of Northwestern Polytechnical University,ChinaProject(20096102110012)supported by a Special Research Fund for Doctoral Disciplines in Colleges and Universities of the Ministry of Education,China
文摘Directionally solidified （DS） specimens of Nb-Ti-Si based ultrahigh temperature alloy were heat-treated at （1 500 ℃, 50 h） and （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, respectively. The results show that the microstructures become uniform, the long and big primary （Nb,X）sSi3 （X represents Ti and Hf elements） plates in the DS specimens are broken into small ones, and the eutectic cells lose their lamellar morphology and their interfaces become blurry after heat-treatment. Meanwhile, the （Nb,X）sSi3 slices in the eutectic cells of the DS specimens coarsen obviously after heat-treatment. Homogenizing and aging treatments could effectively eliminate elemental microsegregation, and the segregation ratios of all elements in niobium solid solution （Nbss） in different regions tend to 1. After heat-treatment, the microhardness of retained eutectic cells increases evidently, and the maximum value reaches HV1 404.57 for the specimen directionally solidified with a withdrawing rate of 100 μm/s and then heat-treated at （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, which is 72.8 % higher than that under DS condition.
