塑性变形对Mg－3．6％Sm合金机械性能和组织的影响

具有密度小和比强度高的镁合金可用作轻结构材料。用稀土金属合金化的镁合金有高的室温强度，高温强度性能也有提高。本文研究了塑性变形提高含钐的镁合金的强度的可能性。

未技术磁化钢铁材料塑性变形区域的磁性出现

分析了常温条件下不同化学成分的未技术磁化钢铁材料在不同力状态作用下的塑料变形区域的磁性出现。结果表明：未技术磁化铁磁性组织钢铁材料的单向静拉伸断口的塑性变形区域出现了磁性。

Microstructural evolution and deformation mechanisms of superplastic aluminium alloys:A review

Aluminium alloy is one of the earliest and most widely used superplastic materials.The objective of this work is to review the scientific advances in superplastic Al alloys.Particularly,the emphasis is placed on the microstructural evolution and deformation mechanisms of Al alloys during superplastic deformation.The evolution of grain structure,texture,secondary phase,and cavities during superplastic flow in typical superplastic Al alloys is discussed in detail.The quantitative evaluation of different deformation mechanisms based on the focus ion beam(FIB)-assisted surface study provides new insights into the superplasticity of Al alloys.The main features,such as grain boundary sliding,intragranular dislocation slip,and diffusion creep can be observed intuitively and analyzed quantitatively.This study provides some reference for the research of superplastic deformation mechanism and the development of superplastic Al alloys.

Plastic yielding of NiTi shape memory alloy under local canning compression

As a new attempt, local canning compression was applied in order to implement large plastic deformation of nickel-titanium shape memory alloy （NiTi SMA） at room temperature. The plastic mechanics of local canning compression of NiTi SMA was analyzed according to the slab method as the well as plastic yield criterion. Transmission electron microscopy （TEM）, high resolution transmission electron microscopy （HRTEM） and scanning electron microscopy （SEM） were used to study the microstructural evolution as well as deformation behavior of NiTi samples under local canning compression. Increasing the hydrostatic pressure with the increase in the outer diameters of the steel cans is responsible for suppressing the initiation and growth of the micro-cracks, which contributes to enhancing the plasticity ofNiTi SMA and avoiding the occurrence of brittle fracture. Plastic deformation of NiTi SMA under a three-dimensional compressive stress state meets von-Mises yield criterion at the true strains ranging from about 0.15 to 0.50, while in the case of larger plastic strain, von-Mises yield criterion is unable to be met since the amorphous phase arises in the deformed NiTi sample.

Viscoplastic friction and microstructural evolution behavior of laser-clad Co-Cr-Ni-Mo coating

The viscoplastic friction and nanostructure formation mechanism of laser-clad Co-based coating were studied by rotary friction between laser-clad Co-Cr-Ni-Mo coating and WC-Co rod.The friction coefficient,friction interface temperature and axial displacement—time curves during rotary friction process were measured.The results showed that all the curves firstly experienced rising stage and then steady stage.The rising stage corresponded to sliding friction while the steady stage corresponded to viscoplastic friction.After viscoplastic friction processing,three typical zones of viscoplastic deformation zone,thermo-mechanically affected zone,and original laser-clad zone can be observed successively from the friction surface to the interior.The viscoplastic deformation significantly crushed the network M23C7 phase in original laser-clad zone and made it dispersively distributed with equiaxial shape and in nano-scale.The viscoplastic zone,in width of 37-131 μm,is mainly characterized by refined M23C7 and α-Co phase with grain size bellow 50 nm,and even a small quantity of amorphous.Thus,the hardness of viscoplastic zone about HV997 was improved compared with the hardness of original laser-clad zone about HV600.

Static cyclic-loading test on new type of rigid connection of steel girder and reinforced concrete pier

A new type of rigid connection of steel girder and reinforced concrete pier of a bridge is proposed. The components in rigid connection are installed by high strength bolts on the spot, which are very convenient in construction. The moment from superstructure can be effectively transferred to substructure, and the plates provided for shear transferring can withstand the majority of total horizontal force. With static cyclic loading test, useful experimental data is obtained on the new type of connection of steel superstructure and concrete substructure. As a result, the stress transfer mechanism of the rigid connection can be made clearly and the seismic performance of this structure can also be clarified. Compared computed strength and ductility with actual results, it can be found that this type of connection has good energy absorption capacity in spite of large displacement and no local buckling arises at the locations where stress concentration occurs. Because of doing away with the expensive bearing, this new type of composite structure can be expected to construct a bridge with high seismic resistant capacity thus saving in total construction cost.

Microstructure and mechanical properties of AZ61 magnesium alloy prepared by repetitive upsetting-extrusion

The process of repetitive upsetting-extrusion （RUE） was used to achieve severe plastic deformation （SPD） for an as-cast AZ61 magnesium alloy in temperature range of 285-380 ℃. The microstructure and mechanical properties of the as-cast and RUE processed AZ61 alloys were investigated. The results indicated that homogeneous fine-grained structure with mean grain size of 3.5 μm was obtained as the accumulated true strain in the axial direction increased to 4.28 after three RUE passes at 285 ℃. The dominant reason of grain refinement was considered the dynamic recrystallization induced by strain localization. It was also found that the microstructural evolution was affected by temperature and accumulated deformation. The mechanical properties of RUE processed AZ61 alloys were significantly improved owing to grain refinement. Furthermore, the relationship between deformation parameters and mechanical properties of AZ61 alloy prepared by RUE processing was revealed by tensile tests carried out at room temperature.

Failure mechanism of as-cast Mg-6Zn-2Er alloy during tensile test at room temperature

Tensile test of the as-cast Mg-6Zn-2Er alloy was conducted at room temperature. The results indicate that the alloy is inclined to failure when the strain reaches 5.6%. The coarse secondary phases are responsible for the failure, especially for the Mg3Zn3Er2 phase （W-phase）. It is indicated that the existence of the W-phase activates the stress concentrations due to the incapacity of W-phase for the load transfer, which results in the void at the inner of the W-phase. In comparison, the interface between the matrix and the secondary phase is stable. In conclusion, the characters of the secondary phases with respect to size, distribution, morphology and type, play an important role in the plastic deformation behavior of the alloy.

Rheological properties of low consistency TMP from thinning wood of Chinese Fir

The rheological behavior of low consistency thermomechanical pulp of Chinese fir harvested by intermediate thinning was analyzed. The results show that the apparent viscosity of pulp changed along with the beating degree, pulp consistency and shearing velocity. With the increasing of pulp consistency, the apparent viscosity of pulp increased gradually. Beating degree of pulp had an effect on microstructure of pulp. The apparent viscosity of pulp declined as beating degree of pulp increased, and the apparent viscosity of pulp fell along with the shearing velocity increasing. Based on the results, the rheological models are set up. The models showed that the fluid types of the low consistency pulp could be described as pseudoplastics fluids （non-Newtonian fluids）.

Effects of plastic deformation on precipitation behavior and tensile fracture behavior of Mg-Gd-Y-Zr alloy

The effects of plastic deformation on precipitation behavior and tensile fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results indicate that more precipitation cores can be provided by the crystal defects caused by the plastic deformation,as well as increasing the amount of β＇ phases,and the formation of precipitations at grain boundaries and interfaces between the twins and matrix.Because of an increase in precipitations,the dislocation slipping during deformation process is effectively hindered and the matrix is strengthened,especially for the 2% deformed alloy which can achieve a good combination of strength and ductility.With increasing the plastic deformation,the microcracks occur at the interface between grain boundary precipitations and matrix,and then propagate intergranularly.When intergranular fracture combines with the formation of smoothing facets on the fracture surface,the tensile properties decrease.

Grain statistics effect on deformation behavior in asymmetric rolling of pure copper foil by crystal plasticity finite element model

The grain statistics effect was investigated through asymmetric rolling of pure copper foil by a realistic polycrystalline aggregates model and crystal plasticity element finite model.A polycrystalline aggregate model was generated and a crystal plasticity-based finite element model was developed for each grain and the specimen as a whole.The crystal plasticity model itself is rate dependent and accounts for local dissipative hardening effects and the original orientation of each grain was generated based on the orientation distribution function（ODF）.The deformation behaviors,including inhomogeneous material flow,decrease of contact press and roll force with the increase of grain size for the constant size of specimens,were studied.It is revealed that when the specimens are composed of only a few grains across thickness,the grains with different sizes,shapes and orientations are unevenly distributed in the specimen and each grain plays a significant role in micro-scale plastic deformation and leads to inhomogeneous deformation and the scatter of experimental and simulation results.The slip system activity was examined and the predicted results are consistent with the surface layer model.The slip band is strictly influenced by the misorientation of neighbor grain with consideration of slip system activity.Furthermore,it is found that the decrease of roll force and the most active of slip system in surface grains are caused by the increase of free surface grain effect when the grain size is increased.The results of the physical experiment and simulation provide a basic understanding of micro-scaled plastic deformation behavior in asymmetric foil rolling.

Numerical simulation of ductile fracture behavior for aluminum alloy sheet under cyclic plastic deformation

A numerical analysis of mechanical behavior of aluminum alloy sheet under cyclic plastic deformation was investigated.Forming limit at fracture was derived from Cockcroft-Latham ductile damage criterion.The strain path of bending center of incremental roller hemming could be accepted as a kind of plane strain bending deformation process.Incremental rope roller hemming could be used to alleviate ductile fracture behavior by changing the stress state of the hemming-effected area.SEM observation on the fracture surface indicates that cyclic plastic deformation affects ductile fracture mechanism.

国际经济秩序变迁的理论与现实——基于结构化概念的分析

国际秩序是观念、制度和权势在特定国际环境下共同作用的结果,国际事务中的每一次重大变化都会对国际经济秩序产生重要影响,甚至不同程度地改变国际经济秩序。本文致力于通过学术探讨改进现有研究中存在的一些不足:一是从结构化概念和系统科学的角度解析国际经济秩序,构建文章的主要分析框架,包括基本层的本质含义和生成维度、第二层的狭义与广义环境和第三层的质化指标。二是总结“观念-制度-权势”三维机制,探讨观念、制度和权势生成国际经济秩序的运作机理。三是着眼于国际经济秩序的构成要件以及国际经济秩序生产过程中的外部环境、霸权国与大国的作用,分析国际经济秩序的可变性与可塑性。四是根据国际经济秩序在上述环节中的可塑性和“观念-制度-权势”三维机制,探讨中国提升国际地位、增强战略能力和推动国际经济秩序朝着公正合理的方向发展的现实路径和有效措施。

PROPERTIES OF BIODEGRADABLE THERMOPLASTIC STARCH

Thermoplastic starch is a kind of modified starch produced by mixing starch with additives and processing the mixture in an extruder. The mechanical properties, including tensile strength and elongation at break, biodegradability and rheological properties were studied. Glycerol and urea, to some extent, can both decrease the tensile strength and increase percentage elongation at break, because the former acts as a plasticizer and the latter can break down interactions among starch macromolecules. Thermoplastic starch shows thermoplasticity and its melt behaves as a pseudoplastic liquid at a low shear rate. Its biodegrading extent is slightly higher than that of native starch. The molecular weight of starch displays a decreasing tendency after thermoplastic modification.

Study on mechanical properties of composite materials by in-situ tensile test

The mechanical properties of the SiC fiber-reinforced Mg-Al metal matrix composite materials have been studied on internal microstructure by (scanning electron microscopy) SEM in-situ tensile test. The emergence and propagation of the crack, and the fracture behavior in materials have been observed and studied. It is found that in the case of the tensile test, the crack emerged in SiC fiber initially. In the case of the strong cohesion of the fiber-metal interface, the crack propagated in the fiber, meanwhile the fibers in the neighborhood of the cracked fiber began to crack and the Mg-Al metal deformed plastically, and at last the material fractured. Otherwise the toughness of the materials grows in the case of the lower cohesion of the fiber-metal matrix interface.

Simulation of mechanical behavior of AZ31 magnesium alloy during twin-dominated large plastic deformation

Experiments and visco-plastic self-consistent (VPSC) simulations were used to quantify the amount of twinning and the relationship to stress?strain behavior in a textured Mg?3Al?1Zn plate. Two different compression directions were utilized to favor{1012} extension or{1011} compression twinning.{1012} twins nucleate at the beginning of plastic deformation and grow to consume the parent grains completely. During compression along the normal direction,{1011} twinning and{1011}?{1012} double twinning start at strain of 0.05, and the number of twins increases until rupture, above strain of 0.15.{1011} and{1011}?{1012} twinning also occur during compression along the transverse direction, start at strain of 0.06 and then multiply in grains totally reoriented by{1012} twins. Using suitable parameters, the VPSC model can accurately predict the occurrence of extension, compression and double-twinning as well as the flow stresses and deformed textures. According to VPSC simulations, twinning and slip have the same latent hardening parameters.

Construction and solution of strain model along thickness of aluminum alloy plate under plastic deformation

A thickness strain model of aluminium alloy plate under plastic deformation,based on thin plate assumption was proposed.It is found that when ratio of stress fractions is constant during in-plane loading,ratios of strain components under various loading conditions are linearly related and these points of ratios form a η-η line.Under these simple loadings,strains in thickness direction can be easily calculated by the η-η line equation without integral and differential work.When the plate is under more complicated loading conditions,the thickness can be computed by the proposed optimization and piecewise calculation model.Validation computations indicate that the relative error of the results of the presented model is less than 0.75% compared with the proven theories and FE simulation.Therefore,the developed model can be applied to engineering calculation,e.g.pre-stretching analysis of aerospace aluminium thick plate,with acceptable accuracy.

内外圆表面滚压加工

介绍一种内外圆表面精加工的新方法──滚压加工。利用硬质合金滚压头对零件内外圆表面旋转挤压,使金属表面产生塑性变形,从而达到零件的尺寸精度和表面粗糙度要求,并在表面产生残余压应力。该工艺替代了磨削加工和喷丸处理,大大提高生产效率并降低了生产成本。

Slip deformation mechanism of α-Zr at 700 °C

Mechanical properties, corrosion behavior and hydrogen absorption of zirconium alloys are related to the texture resulting from prior forming processes. In order to investigate the high temperature deformation behavior of α-Zr, compression tests at 700 ℃, microstructure measurements via EBSD, and visco-plastic self-consistent modeling were performed. Twinning activity was negligible at strain rates ε≤1s^-1. The strain rate sensitivity m=0.17 seemed to be the same for all slip modes. Material parameters were fitted to reproduce the mechanical anisotropy and deformed texture, and were validated by comparing the simulated and measured strain anisotropy. The best-fit simulation showed that at high temperatures prismatic slip was the easiest deformation mode and pyramidal <c+a> was the hardest, but basal slip and pyramidal slip operated easily and in large amount.