We present here a large (3 cm) hyperplastic gastric polyp prolapsed into duodenum and caused outlet obstruction and iron deficiency anemia in 60 years old male patient.Endoscopic removal was performed successfully.
In order to improve the bonding strength between piston alloys and cast iron ring of aluminum piston with reinforced cast iron ring,the different methods of the surface treatments(shot blasting and sand blasting) to t...In order to improve the bonding strength between piston alloys and cast iron ring of aluminum piston with reinforced cast iron ring,the different methods of the surface treatments(shot blasting and sand blasting) to the cast iron ring are experimented.The optical micrograph shows that an intermetallic layer and a ligulate shaped structure are formed between piston alloys and cast iron base ring.After sand blasting treatment,the ring surface is non-metal shiny,matte-like and has no obvious pits.The intermetallic layer thickness formed between piston alloys and cast iron is thinner and more equally distributed after sand blasting to the ring.The content of the graphite distributed the interfacial zone after the shot blasting treatment is little.With the increase of time by sand blasting,the hardness starts to slightly descend.The bonding strength of the sample by sand blasting is obviously higher than that by shot blasting and increases from 9.32 MPa to 19.53 MPa.展开更多
During the start-up and shut-down phase of reciprocating compressors, the loads on all components of driven train system are very high. In this paper a method for calculating the forces on coupling, e-motor, crank sha...During the start-up and shut-down phase of reciprocating compressors, the loads on all components of driven train system are very high. In this paper a method for calculating the forces on coupling, e-motor, crank shaft as well other components of the system will be described. The modelling of the electrical induction motor, coupling, crank shaft, damper as well as the compressor resistance torque are extremely important in simulating start-up and shut-down of reciprocating compressor. Furthermore the switching torque of the electrical motor and the instantaneous moment of inertia of the reciprocating compressor crank gear are important as well. The transient start-up and shut-down process under loaded and unloaded conditions is described using a non-linear differential equation for driven train system： E-motor--coupling--flywheel--reciprocating compressor--damper. Shaft torsional moments on the drive train and especially on the coupling, whether elastic or stiff, can then only be calculated using numerical simulation. This paper will describe some of the key elements in modelling, simulating and measurements of drive train start-up and shut-down carried out on already operational piston compressor units.展开更多
文摘We present here a large (3 cm) hyperplastic gastric polyp prolapsed into duodenum and caused outlet obstruction and iron deficiency anemia in 60 years old male patient.Endoscopic removal was performed successfully.
基金Project(51101109)supported by the National Natural Science Foundation of China
文摘In order to improve the bonding strength between piston alloys and cast iron ring of aluminum piston with reinforced cast iron ring,the different methods of the surface treatments(shot blasting and sand blasting) to the cast iron ring are experimented.The optical micrograph shows that an intermetallic layer and a ligulate shaped structure are formed between piston alloys and cast iron base ring.After sand blasting treatment,the ring surface is non-metal shiny,matte-like and has no obvious pits.The intermetallic layer thickness formed between piston alloys and cast iron is thinner and more equally distributed after sand blasting to the ring.The content of the graphite distributed the interfacial zone after the shot blasting treatment is little.With the increase of time by sand blasting,the hardness starts to slightly descend.The bonding strength of the sample by sand blasting is obviously higher than that by shot blasting and increases from 9.32 MPa to 19.53 MPa.
文摘During the start-up and shut-down phase of reciprocating compressors, the loads on all components of driven train system are very high. In this paper a method for calculating the forces on coupling, e-motor, crank shaft as well other components of the system will be described. The modelling of the electrical induction motor, coupling, crank shaft, damper as well as the compressor resistance torque are extremely important in simulating start-up and shut-down of reciprocating compressor. Furthermore the switching torque of the electrical motor and the instantaneous moment of inertia of the reciprocating compressor crank gear are important as well. The transient start-up and shut-down process under loaded and unloaded conditions is described using a non-linear differential equation for driven train system： E-motor--coupling--flywheel--reciprocating compressor--damper. Shaft torsional moments on the drive train and especially on the coupling, whether elastic or stiff, can then only be calculated using numerical simulation. This paper will describe some of the key elements in modelling, simulating and measurements of drive train start-up and shut-down carried out on already operational piston compressor units.
