In order to study the fatigue failure mode and fatigue life laws of basalt-aramid and basalt-carbon hybrid fiber reinforced polymer （ FRP ） sheets, fatigue experiments are carried out, considering two hybrid ratios ...In order to study the fatigue failure mode and fatigue life laws of basalt-aramid and basalt-carbon hybrid fiber reinforced polymer （ FRP ） sheets, fatigue experiments are carried out, considering two hybrid ratios of 1 ： 1 and 2：1 under different stress levels from 0.6 to 0.95. The results show that fractures occur first in carbon fibers or aramid fibers for the specimens with hybrid ratio of 1： 1, namely B1A1 and B1C1, while a fracture occurs first in basalt fibers for the specimens with a hybrid ratio of 2： 1, namely B2A1 and B2C1. The fatigue lives of the hybrid FRP sheets increase with the improvement of the content of carbon fibers or aramid fibers, and the influence of the carbon fibers content improvement to fatigue life is more significant. The fatigue performance of B2A1 is relatively worse, while the fatigue performance of B1C1 and B2C1 is relatively better. Finally, a new fatigue stiffness degradation model with dual variables and double inflection points is presented, which is applicable to both hybrid and normal FRP sheets.展开更多
A 2 5GHz fully integrated LC VCO is fabricated in a standard single poly 4 metal 0 35μm digital CMOS process,using a complementary cross coupled topology for lowering power dissipation and reducing the effect of...A 2 5GHz fully integrated LC VCO is fabricated in a standard single poly 4 metal 0 35μm digital CMOS process,using a complementary cross coupled topology for lowering power dissipation and reducing the effect of 1/ f noise.An on chip LC filtering technique is used to lower the high frequency noise.Accumulation varactors are used to widen frequency tuning.The measured tuning range is 23 percent.A single hexadecagon symmetric on chip spiral is used with grounded shield pattern to reduce the chip area and maximize the quality factor.A phase noise of -118dBc/Hz at 1MHz offset is measured.The power dissipation is 4mA at V DD =3 3V.展开更多
Both the vertical cavity surface emitting diodes and detectors are fabricated by using the epitaxial wafer with resonant cavity structure.Their characteristics are analyzed.The light emitters have high spectral purity...Both the vertical cavity surface emitting diodes and detectors are fabricated by using the epitaxial wafer with resonant cavity structure.Their characteristics are analyzed.The light emitters have high spectral purity of 4 8nm and high electroluminescence intensity of 0 7mW while injection current is 50mA.A 1×16 array of surface emitting light device is tested on line by probes and then used for module.The light detectors have wavelength selectivity and space selectivity.The required difference in input mirror reflectivity between emitters and detectors can easily be achieved though varying the numbers of top DBR period by etching.展开更多
A CMOS （complementary metal-oxide-semiconductor transistor） low-dropout regulator （LDO） with 3. 3 V output voltage and 100 mA output current for system-on-chip applications to reduce board space and external pins ...A CMOS （complementary metal-oxide-semiconductor transistor） low-dropout regulator （LDO） with 3. 3 V output voltage and 100 mA output current for system-on-chip applications to reduce board space and external pins is presented. By utilizing a dynamic slew-rate enhancement（SRE） circuit and nested Miller compensation （NMC） on the LDO structure, the proposed LDO provides high stability during line and load regulation without off-chip load capacitors. The overshot voltage is limited within 550 mV and the settling time is less than 50 μs when the load current decreases from 100 mA to 1 mA. By using a 30 nA reference current, the quiescent current is 3.3 μA. The proposed design is implemented by CSMC 0. 5 μm mixed-signal process. The experimental results agree with the simulation results.展开更多
This paper represented the numerical analysis of the FRP （fiber reinforced plastics） tunnel lining which was used for maintaining the old tunnel. An old tunnel covered with a concrete is prone to deteriorate due to ...This paper represented the numerical analysis of the FRP （fiber reinforced plastics） tunnel lining which was used for maintaining the old tunnel. An old tunnel covered with a concrete is prone to deteriorate due to an aging effect and a v^ater penetration. In the rehabilitation of lining concrete, a steel plate and FRP or carbon sheet have been applied. However, these sheets show small flexural rigidity and do not flow out the penetrating water. In this paper, FRP corrugate sheet was proposed. The tunnel lining was made by FRP corrugate sheet that supported the lining concrete in the tunnel and flowed the water and the moisture swept on the tunnel surface. The FRP corrugate sheet was supported by the anchor bolts. In numerical analyses, the finite element degenerate shell was adopted to represent the FRP sheet behavior. Assuming that the concrete liner at the top was fallen down, the peeled concrete was applied as the load. From the numerical analysis, the effectiveness of the FRO corrugate sheet was confirmed.展开更多
The effects of graphene nanoplates(GNPs)on the microstructures and mechanical properties of nanoparticlesstrengthening activating tungsten inert gas arc welding(NSA-TIG)welded AZ31magnesium alloy joints were investiga...The effects of graphene nanoplates(GNPs)on the microstructures and mechanical properties of nanoparticlesstrengthening activating tungsten inert gas arc welding(NSA-TIG)welded AZ31magnesium alloy joints were investigated.It wasfound that compared with those of activating TIG(A-TIG),and obvious refinement ofα-Mg grains was achieved and the finestα-Mggrains of fusion zone of NSA-TIG joints were obtained in the welded joints with TiO2+GNPs flux coating.In addition,thepenetrations of joints coated by TiO2+GNPs flux were similar to those coated by the TiO2+SiCp flux.However,the welded jointswith TiO2+GNPs flux coating showed better mechanical properties(i.e.,ultimate tensile strength and microhardness)than those withTiO2+SiCp flux coating.Moreover,the generation of necking only occurred in the welded joints with TiO2+GNPs flux.展开更多
基金The National Natural Science Foundation of China(No.51108238)
文摘In order to study the fatigue failure mode and fatigue life laws of basalt-aramid and basalt-carbon hybrid fiber reinforced polymer （ FRP ） sheets, fatigue experiments are carried out, considering two hybrid ratios of 1 ： 1 and 2：1 under different stress levels from 0.6 to 0.95. The results show that fractures occur first in carbon fibers or aramid fibers for the specimens with hybrid ratio of 1： 1, namely B1A1 and B1C1, while a fracture occurs first in basalt fibers for the specimens with a hybrid ratio of 2： 1, namely B2A1 and B2C1. The fatigue lives of the hybrid FRP sheets increase with the improvement of the content of carbon fibers or aramid fibers, and the influence of the carbon fibers content improvement to fatigue life is more significant. The fatigue performance of B2A1 is relatively worse, while the fatigue performance of B1C1 and B2C1 is relatively better. Finally, a new fatigue stiffness degradation model with dual variables and double inflection points is presented, which is applicable to both hybrid and normal FRP sheets.
文摘A 2 5GHz fully integrated LC VCO is fabricated in a standard single poly 4 metal 0 35μm digital CMOS process,using a complementary cross coupled topology for lowering power dissipation and reducing the effect of 1/ f noise.An on chip LC filtering technique is used to lower the high frequency noise.Accumulation varactors are used to widen frequency tuning.The measured tuning range is 23 percent.A single hexadecagon symmetric on chip spiral is used with grounded shield pattern to reduce the chip area and maximize the quality factor.A phase noise of -118dBc/Hz at 1MHz offset is measured.The power dissipation is 4mA at V DD =3 3V.
文摘Both the vertical cavity surface emitting diodes and detectors are fabricated by using the epitaxial wafer with resonant cavity structure.Their characteristics are analyzed.The light emitters have high spectral purity of 4 8nm and high electroluminescence intensity of 0 7mW while injection current is 50mA.A 1×16 array of surface emitting light device is tested on line by probes and then used for module.The light detectors have wavelength selectivity and space selectivity.The required difference in input mirror reflectivity between emitters and detectors can easily be achieved though varying the numbers of top DBR period by etching.
基金The Key Science and Technology Project of Zhejiang Province(No.2007C21021)
文摘A CMOS （complementary metal-oxide-semiconductor transistor） low-dropout regulator （LDO） with 3. 3 V output voltage and 100 mA output current for system-on-chip applications to reduce board space and external pins is presented. By utilizing a dynamic slew-rate enhancement（SRE） circuit and nested Miller compensation （NMC） on the LDO structure, the proposed LDO provides high stability during line and load regulation without off-chip load capacitors. The overshot voltage is limited within 550 mV and the settling time is less than 50 μs when the load current decreases from 100 mA to 1 mA. By using a 30 nA reference current, the quiescent current is 3.3 μA. The proposed design is implemented by CSMC 0. 5 μm mixed-signal process. The experimental results agree with the simulation results.
文摘This paper represented the numerical analysis of the FRP （fiber reinforced plastics） tunnel lining which was used for maintaining the old tunnel. An old tunnel covered with a concrete is prone to deteriorate due to an aging effect and a v^ater penetration. In the rehabilitation of lining concrete, a steel plate and FRP or carbon sheet have been applied. However, these sheets show small flexural rigidity and do not flow out the penetrating water. In this paper, FRP corrugate sheet was proposed. The tunnel lining was made by FRP corrugate sheet that supported the lining concrete in the tunnel and flowed the water and the moisture swept on the tunnel surface. The FRP corrugate sheet was supported by the anchor bolts. In numerical analyses, the finite element degenerate shell was adopted to represent the FRP sheet behavior. Assuming that the concrete liner at the top was fallen down, the peeled concrete was applied as the load. From the numerical analysis, the effectiveness of the FRO corrugate sheet was confirmed.
基金Project(51375511) supported by the National Natural Science Foundation of ChinaProject(cstc2016jcyj A0167) supported by the Research Program of Basic Research and Frontier Technology of Chongqing of China+1 种基金Project(SF201602) supported by the Science and Technology Project in the Field of Social Development of Shapingba District of Chongqing of ChinaProject(XJ201608) supported by the Key Industry Technology Innovation Funds of Science and Technology Development Board of Xiangcheng District of Suzhou of China
文摘The effects of graphene nanoplates(GNPs)on the microstructures and mechanical properties of nanoparticlesstrengthening activating tungsten inert gas arc welding(NSA-TIG)welded AZ31magnesium alloy joints were investigated.It wasfound that compared with those of activating TIG(A-TIG),and obvious refinement ofα-Mg grains was achieved and the finestα-Mggrains of fusion zone of NSA-TIG joints were obtained in the welded joints with TiO2+GNPs flux coating.In addition,thepenetrations of joints coated by TiO2+GNPs flux were similar to those coated by the TiO2+SiCp flux.However,the welded jointswith TiO2+GNPs flux coating showed better mechanical properties(i.e.,ultimate tensile strength and microhardness)than those withTiO2+SiCp flux coating.Moreover,the generation of necking only occurred in the welded joints with TiO2+GNPs flux.
