This paper presents a 12-channel,30Gb/s front-end amplifier realized in standard 0.18μm CMOS technology for parallel optlc-fiber receivers. In order to overcome the problem of inadequate bandwidth caused by the large...This paper presents a 12-channel,30Gb/s front-end amplifier realized in standard 0.18μm CMOS technology for parallel optlc-fiber receivers. In order to overcome the problem of inadequate bandwidth caused by the large parasitical capacitor of CMOS photo-detectors,a regulated-cascode structure and noise optimization are used in the design of the transimpedance amplifier. The experimental results indicate that, with a parasitical capacitance of 2pF,a single channel is able to work at bite rates of up to 2.5Gb/s,and a clear eye diagram is obtained with a 0. 8mVpp input. Furthermore, an isolation structure combined with a p^＋ guard.ring （PGR）, an n^＋ guard-ring （NGR）,and a deep-n-well （DNW） for parallel amplifier is also presented. Taking this combined structure, the crosstalk and the substrate noise coupling have been effectively reduced. Compared with the isolation of PGR or PGR ＋ NGR,the measured results show that the isolation degree of this structure is improved by 29.2 and 8. ldB at 1GHz,and by 8. 1 and 2. 5dB at 2GHz,respectively. With a 1.8V supply,each channel of the front-end amplifier consumes a DC power of 85mW,and the total power consumption of 12 channels is about 1W.展开更多
Remote sensing technique, replacing conventional sonar bathymetry technique, has become an effective complementary method of mapping submarine terrain where special conditions make the sonar technique difficult to be ...Remote sensing technique, replacing conventional sonar bathymetry technique, has become an effective complementary method of mapping submarine terrain where special conditions make the sonar technique difficult to be carried out. At the same time, as one kind of data set, multispectral remote sensing data has the disadvantage of being influenced by the variable bottom types in shallow seawater, when it is applied in bathymetry. This paper puts forward a new method to extract water depth information from multispectral data, considering the bottom classification and the true water depth accuracy. That is the Principal Component Analysis (PCA) technique based on the bottom classification. By the least square regression with significance, the experiment near Qingdao City has obtained more satisfactory bathymetry accuracy than that of the traditional single-band method, with the mean absolute error about 2.57m.展开更多
This paper presents a seafloor classification method of multibeam sonar data, based on the use of Adaptive Resonance Theory （ART） neural networks. A general ART-based neural network, Fuzzy ARTMAP, has been proposed ...This paper presents a seafloor classification method of multibeam sonar data, based on the use of Adaptive Resonance Theory （ART） neural networks. A general ART-based neural network, Fuzzy ARTMAP, has been proposed for seafloor classification of multibeam sonar data. An evolutionary strategy was used to generate new training samples near the cluster boundaries of the neural network, therefore the weights can be revised and refined by supervised learning. The proposed method resolves the training problem for Fuzzy ARTMAP neural networks, which are applied to seafloor classification of multibeam sonar data when there are less than adequate ground-troth samples. The results were synthetically analyzed in comparison with the standard Fuzzy ARTMAP network and a conventional Bayesian classifier. The conclusion can be drawn that Fuzzy ARTMAP neural networks combining with GA algorithms can be alternative powerful tools for seafloor classification of multibeam sonar data.展开更多
The multibeam sonars can provide hydrographic quality depth data as well as hold the potential to provide calibrated measurements of the seafloor acoustic backscattering strength. There has been much interest in utili...The multibeam sonars can provide hydrographic quality depth data as well as hold the potential to provide calibrated measurements of the seafloor acoustic backscattering strength. There has been much interest in utilizing backscatters and images from multibeam sonar for seabed type identification and most results are obtained. This paper has presented a focused review of several main methods and recent developments of seafloor classification utilizing multibeam sonar data or/and images. These are including the power spectral analysis methods, the texture analysis, traditional Bayesian classification theory and the most active neural network approaches.展开更多
A shallow water tomography scheme based on the modal wave number inversion technique is considered in this paper. The scheme is based on the assumption that modal wave number for trapped modes can be measured in a sui...A shallow water tomography scheme based on the modal wave number inversion technique is considered in this paper. The scheme is based on the assumption that modal wave number for trapped modes can be measured in a suitable way. The tomographic inversion is accomplished in two steps: firstly, the bottom parameters are inverted by using the bottom reflection phase shift with the known sound speed profile; secondly, the variation of sound speed profile at different time is inverted provided the bottom parameters are known. A numerical simulation shows that the proposed scheme works well, and the sensitivity analysis of sound speed profile inversion is performed for shallow water environmental parameters: sound speed, density and attenuation coefficient of the bottom.展开更多
China’s coastal waters are turbid and the properties of the seabed are complex. This negatively impacts the performance of underwater detection equipment. The properties of sound absorption in turbid water are not we...China’s coastal waters are turbid and the properties of the seabed are complex. This negatively impacts the performance of underwater detection equipment. The properties of sound absorption in turbid water are not well understood. In this paper, the coefficient of sound absorption in turbid water was measured by the reverberation technique. All work was done in a reverberation barrel made of seamless aluminum. First, pure water was poured into the reverberation barrel and its reverberation time measured. Next, various concentrations of turbid water were poured into the barrel and their reverberation time measured. After all data had been gathered, the coefficient of sound absorption in turbid water of different concentrations was calculated. From this we determined a law of sound absorption in turbid water as summarized in the paper.展开更多
In this study,a 2kHz Tonpilz projector was designed using a Terfenol-D and modeled in ATILA.For the purpose of modeling studies,it has been determined that a radiating head mass exhibits better transmitting current re...In this study,a 2kHz Tonpilz projector was designed using a Terfenol-D and modeled in ATILA.For the purpose of modeling studies,it has been determined that a radiating head mass exhibits better transmitting current response（TCR） at 136 mm diameter,where the resonance occurs at 2.4kHz and the peak value of 118 dB re 1 μPa/A at 1 m occurs at 12 kHz.Also bolt at a 46mm distance from the center of the head mass offers resonance at 2.4kHz,and the peak value of 115.3 dB re 1 μPa/A at 1m occurs at 11.5kHz.This optimized design is fabricated and molded with polyurethane of 3mm thickness.The prototype was tested at the Acoustic Test Facility（ATF） of National Institute of Ocean Technology（NIOT） for its underwater performances.Based on the result,the fundamental resonance was determined to be 2.18kHz and the peak value of TCR of 182 dB re 1 μPa/A at 1m occurs at 14 kHz.The maximum value of the RS was found to be -190 dB re 1V/μPa at 1m at a frequency of 2.1kHz.展开更多
Multi-beam Sonar and Side-scan Sonar compensate each other. In order to fully utilize all information, it is necessary to fuse two kinds of image and data. And the image co-registration is an important and complicated...Multi-beam Sonar and Side-scan Sonar compensate each other. In order to fully utilize all information, it is necessary to fuse two kinds of image and data. And the image co-registration is an important and complicated job before fusion. This paper suggests combining bathymetric data with intensity image, obtaining the characteristic points through the minimal angles of lines, and then deciding the corresponding image points by the maximal correlate coefficient in searching space. Finally, the second order polynomial is applied to the deformation model. After the images have been co-registered, Wavelet is used to fuse the images. It is shown that this algorithm can be used in the flat seafloor or the isotropic seabed. Verification is made in the paper with the observed data.展开更多
A new in-situ seabed acoustic measurement system is developed for direct in-situ measurement of sediment geoacoustic properties （compressional wave velocity and attenuation）. The new in-situ system consists of two p...A new in-situ seabed acoustic measurement system is developed for direct in-situ measurement of sediment geoacoustic properties （compressional wave velocity and attenuation）. The new in-situ system consists of two parts： the deck control unit and the underwater measurement unit. The underwater measurement unit emits sonic waves that propagate through the seafloor sediment, receives the returning signals, and transmits them to the deck control unit for waveform display and analysis. The entire operation is controlled and monitored in real time by the deck control unit on the research vessel and can provide recording of full waveforms to determine the sound velocity and attenuation. This paper outlines the design of the system, the measurement process, and demonstrates its application in tests carded out on seabed sediment off the Qingdao coast, China. The test results show that the system performed well and rapidly provided accurate in-situ acoustic velocity and attenuation estimates of the seafloor sediment.展开更多
The sound velocity of seafloor sediments from shallow seas can provide important information for harbor design, and ocean and seacoast engineering projects. In this study, in situ measurements were used to obtain accu...The sound velocity of seafloor sediments from shallow seas can provide important information for harbor design, and ocean and seacoast engineering projects. In this study, in situ measurements were used to obtain accurate sediment sound velocities at 45 stations offshore of Qingdao. The relationships between the sound velocity and granular properties of the seafloor sediments were analyzed. Sound velocity showed an increase with the sand content, sand-clay ratio, and sorting coefficient; and a nonlinear decreasing trend with increasing mean grain size and clay content. We plotted a sound velocity distribution map, which shows that the sound velocity was closely related to the geological environment. Previous empirical equations suggested by Hamilton, Anderson, and Liu were used to calculate the velocity with grain size. A comparison between the measured and calculated velocities indicates that the empirical equations have territorial limitations, and extensive data are essential to establish global empirical equations. Future work includes the calibration of the laboratory acoustic measurements with an in situ technique.展开更多
文摘This paper presents a 12-channel,30Gb/s front-end amplifier realized in standard 0.18μm CMOS technology for parallel optlc-fiber receivers. In order to overcome the problem of inadequate bandwidth caused by the large parasitical capacitor of CMOS photo-detectors,a regulated-cascode structure and noise optimization are used in the design of the transimpedance amplifier. The experimental results indicate that, with a parasitical capacitance of 2pF,a single channel is able to work at bite rates of up to 2.5Gb/s,and a clear eye diagram is obtained with a 0. 8mVpp input. Furthermore, an isolation structure combined with a p^＋ guard.ring （PGR）, an n^＋ guard-ring （NGR）,and a deep-n-well （DNW） for parallel amplifier is also presented. Taking this combined structure, the crosstalk and the substrate noise coupling have been effectively reduced. Compared with the isolation of PGR or PGR ＋ NGR,the measured results show that the isolation degree of this structure is improved by 29.2 and 8. ldB at 1GHz,and by 8. 1 and 2. 5dB at 2GHz,respectively. With a 1.8V supply,each channel of the front-end amplifier consumes a DC power of 85mW,and the total power consumption of 12 channels is about 1W.
基金Foundation item: Under the auspices of Scientific Foundation Research Project of the Ministry of Science and Technology and Chinese Academy of Surveying and Mapping (No. F0610)
文摘Remote sensing technique, replacing conventional sonar bathymetry technique, has become an effective complementary method of mapping submarine terrain where special conditions make the sonar technique difficult to be carried out. At the same time, as one kind of data set, multispectral remote sensing data has the disadvantage of being influenced by the variable bottom types in shallow seawater, when it is applied in bathymetry. This paper puts forward a new method to extract water depth information from multispectral data, considering the bottom classification and the true water depth accuracy. That is the Principal Component Analysis (PCA) technique based on the bottom classification. By the least square regression with significance, the experiment near Qingdao City has obtained more satisfactory bathymetry accuracy than that of the traditional single-band method, with the mean absolute error about 2.57m.
文摘This paper presents a seafloor classification method of multibeam sonar data, based on the use of Adaptive Resonance Theory （ART） neural networks. A general ART-based neural network, Fuzzy ARTMAP, has been proposed for seafloor classification of multibeam sonar data. An evolutionary strategy was used to generate new training samples near the cluster boundaries of the neural network, therefore the weights can be revised and refined by supervised learning. The proposed method resolves the training problem for Fuzzy ARTMAP neural networks, which are applied to seafloor classification of multibeam sonar data when there are less than adequate ground-troth samples. The results were synthetically analyzed in comparison with the standard Fuzzy ARTMAP network and a conventional Bayesian classifier. The conclusion can be drawn that Fuzzy ARTMAP neural networks combining with GA algorithms can be alternative powerful tools for seafloor classification of multibeam sonar data.
文摘The multibeam sonars can provide hydrographic quality depth data as well as hold the potential to provide calibrated measurements of the seafloor acoustic backscattering strength. There has been much interest in utilizing backscatters and images from multibeam sonar for seabed type identification and most results are obtained. This paper has presented a focused review of several main methods and recent developments of seafloor classification utilizing multibeam sonar data or/and images. These are including the power spectral analysis methods, the texture analysis, traditional Bayesian classification theory and the most active neural network approaches.
文摘A shallow water tomography scheme based on the modal wave number inversion technique is considered in this paper. The scheme is based on the assumption that modal wave number for trapped modes can be measured in a suitable way. The tomographic inversion is accomplished in two steps: firstly, the bottom parameters are inverted by using the bottom reflection phase shift with the known sound speed profile; secondly, the variation of sound speed profile at different time is inverted provided the bottom parameters are known. A numerical simulation shows that the proposed scheme works well, and the sensitivity analysis of sound speed profile inversion is performed for shallow water environmental parameters: sound speed, density and attenuation coefficient of the bottom.
文摘China’s coastal waters are turbid and the properties of the seabed are complex. This negatively impacts the performance of underwater detection equipment. The properties of sound absorption in turbid water are not well understood. In this paper, the coefficient of sound absorption in turbid water was measured by the reverberation technique. All work was done in a reverberation barrel made of seamless aluminum. First, pure water was poured into the reverberation barrel and its reverberation time measured. Next, various concentrations of turbid water were poured into the barrel and their reverberation time measured. After all data had been gathered, the coefficient of sound absorption in turbid water of different concentrations was calculated. From this we determined a law of sound absorption in turbid water as summarized in the paper.
文摘In this study,a 2kHz Tonpilz projector was designed using a Terfenol-D and modeled in ATILA.For the purpose of modeling studies,it has been determined that a radiating head mass exhibits better transmitting current response（TCR） at 136 mm diameter,where the resonance occurs at 2.4kHz and the peak value of 118 dB re 1 μPa/A at 1 m occurs at 12 kHz.Also bolt at a 46mm distance from the center of the head mass offers resonance at 2.4kHz,and the peak value of 115.3 dB re 1 μPa/A at 1m occurs at 11.5kHz.This optimized design is fabricated and molded with polyurethane of 3mm thickness.The prototype was tested at the Acoustic Test Facility（ATF） of National Institute of Ocean Technology（NIOT） for its underwater performances.Based on the result,the fundamental resonance was determined to be 2.18kHz and the peak value of TCR of 182 dB re 1 μPa/A at 1m occurs at 14 kHz.The maximum value of the RS was found to be -190 dB re 1V/μPa at 1m at a frequency of 2.1kHz.
文摘Multi-beam Sonar and Side-scan Sonar compensate each other. In order to fully utilize all information, it is necessary to fuse two kinds of image and data. And the image co-registration is an important and complicated job before fusion. This paper suggests combining bathymetric data with intensity image, obtaining the characteristic points through the minimal angles of lines, and then deciding the corresponding image points by the maximal correlate coefficient in searching space. Finally, the second order polynomial is applied to the deformation model. After the images have been co-registered, Wavelet is used to fuse the images. It is shown that this algorithm can be used in the flat seafloor or the isotropic seabed. Verification is made in the paper with the observed data.
基金Supported by the National Special Research Fund for Non-Profit Marine Sector(No.200905025)
文摘A new in-situ seabed acoustic measurement system is developed for direct in-situ measurement of sediment geoacoustic properties （compressional wave velocity and attenuation）. The new in-situ system consists of two parts： the deck control unit and the underwater measurement unit. The underwater measurement unit emits sonic waves that propagate through the seafloor sediment, receives the returning signals, and transmits them to the deck control unit for waveform display and analysis. The entire operation is controlled and monitored in real time by the deck control unit on the research vessel and can provide recording of full waveforms to determine the sound velocity and attenuation. This paper outlines the design of the system, the measurement process, and demonstrates its application in tests carded out on seabed sediment off the Qingdao coast, China. The test results show that the system performed well and rapidly provided accurate in-situ acoustic velocity and attenuation estimates of the seafloor sediment.
基金Supported by the National Special Research Fund for Non-Profit Marine Sector(No.200905025)
文摘The sound velocity of seafloor sediments from shallow seas can provide important information for harbor design, and ocean and seacoast engineering projects. In this study, in situ measurements were used to obtain accurate sediment sound velocities at 45 stations offshore of Qingdao. The relationships between the sound velocity and granular properties of the seafloor sediments were analyzed. Sound velocity showed an increase with the sand content, sand-clay ratio, and sorting coefficient; and a nonlinear decreasing trend with increasing mean grain size and clay content. We plotted a sound velocity distribution map, which shows that the sound velocity was closely related to the geological environment. Previous empirical equations suggested by Hamilton, Anderson, and Liu were used to calculate the velocity with grain size. A comparison between the measured and calculated velocities indicates that the empirical equations have territorial limitations, and extensive data are essential to establish global empirical equations. Future work includes the calibration of the laboratory acoustic measurements with an in situ technique.
