高36.88m观音铜像的铸造

巨型观音铜像采用熔模石膏型与蜡模湿砂型分铸，然后拼焊成型。实践证明：该法铸造成本较低、操作简单，且铸件壁厚均匀、变形量小、铸造缺陷较少。

Microstructures and mechanical properties of TC4/AZ91D bimetal prepared by solid-liquid compound casting combined with Zn/Al composite interlayer

To achieve Ti/Mg bimetallic composite with high strength and metallurgical bonding interface,Al interlayer and Zn/Al composite interlayer were used to prepare TC4/AZ91D bimetal composite with metallurgical bonding interface by solid-liquid compound casting,respectively.Al interlayer was prepared on the surface of TC4 alloy by hot dipping,and Zn/Al composite interlayer was prepared by electroplating process.The results suggested that the phases across the interface were Al Ti andα(Al)+Mg_(21)(Al,Zn)_(17)when Zn/Al composite interlayer was used.When Al interlayer was used as interlayer,Al Mg Ti ternary structure and Al_(12)Mg_(17)+δ-Mg eutectic structure were the main phases at the interface.The shear strength of TC4/AZ91D bimetal with Zn/Al composite interlayer was much higher than that with pure Al interlayer,and the value of the shear strength was increased from 48.5 to 67.4 MPa.Thermodynamic models based on different compositions of the interface were established to explain the microstructure evolution of the interfacial zone.

Numerical model and experimental observation for distribution of SiC_p in electromagnetic-centrifugally cast composites

A two-phase numerical model coupled with heat transfer was presented to describe the radial distribution of SiC particles on centrifugally-cast metal matrix composite,and a transverse static magnetic field was concurrently imposed to induce electromagnetic stirring of the melt as it revolved with the mold.Meanwhile,experimental observations were also carried out to examine the radial distribution of SiC particles in pure aluminum.The effects of the imposed magnetic field,particle size and the matrix metals were discussed.The computational results show that the particles tend to be congregated by the centrifugal force,and both increasing the imposed magnetic field and decreasing the particle size tend to result in even distribution of the particles.With the magnetic field varying from 0 to 1 T and the particle size from 550 to 180 μm,a uniform distribution of the particles in the aluminum matrix can be obtained among the computational results.The matrix metal can also influence the particle distributions due to the difference in physical properties of metals.Experimental observation shows similar tendency of particle distributions in aluminum matrix influenced by magnetic field and particle size.However,the chilling effect from the mold wall results in an outer particle-free zone,which is not involved in the numerical model.

Effects of compocasting process parameters on microstructural characteristics and tensile properties of A356-SiC_p composites

The effects of compocasting process parameters on some structural and tensile characteristics of the A356-10% SiCp (volume fraction) composites were studied. Semisolid stirring was carried out at temperatures of 590, 600 and 610 °C with stirring speeds of 200, 400 and 600 r/min for 10, 20 and 30 min. The distribution of the SiC particles within the matrix, porosity content and tensile properties of the obtained samples were examined. The structural evaluations show that by increasing the stirring time and decreasing the stirring temperature, the uniformity in the particle distribution is improved;however, by increasing the stirring speed the homogeneity firstly increases and then declines. It is also found that by increasing all of the processing parameters, the porosity content is enhanced. From the tensile characteristics viewpoint, the optimum values of the speed, temperature and time are found to be 400 r/min, 590 °C and 30 min, respectively. The contribution of the reinforcement distribution uniformity prevails over that of the porosity level to the tensile properties.