The thermal conductivity of Cu/Kovar composites was improved by suppressing element diffusion at the interfaces through the formation of FeWO_(4)coating on the Kovar particles via vacuum deposition.Cu matrix composite...The thermal conductivity of Cu/Kovar composites was improved by suppressing element diffusion at the interfaces through the formation of FeWO_(4)coating on the Kovar particles via vacuum deposition.Cu matrix composites reinforced with unmodified(Cu/Kovar)and modified Kovar(Cu/Kovar@)particles were prepared by hot pressing.The results demonstrate that the interfaces of Cu/FeWO_(4)and FeWO_(4)/Kovar in the Cu/Kovar@composites exhibit strong bonding,and no secondary phase is generated.The presence of FeWO_(4)impedes interfacial diffusion within the composite,resulting in an increase in grain size and a decrease in dislocation density.After surface modification of the Kovar particle,the thermal conductivity of Cu/Kovar@composite is increased by 110%from 40.6 to 85.6 W·m^(-1)·K^(-1).Moreover,the thermal expansion coefficient of the Cu/Kovar@composite is 9.8×10^(-6)K^(-1),meeting the electronic packaging requirements.展开更多
The Al/Si/SiC composites with medium volume fraction for electronic packaging were fabricated by gas pressure infiltration.On the premise of keeping the machinability of the composites,the silicon carbide particles,wh...The Al/Si/SiC composites with medium volume fraction for electronic packaging were fabricated by gas pressure infiltration.On the premise of keeping the machinability of the composites,the silicon carbide particles,which have the similar size with silicon particles（average 13 μm）,were added to replace silicon particles of same volume fraction,and microstructure and properties of the composites were investigated.The results show that reinforcing particles are distributed uniformly and no apparent pores are observed in the composites.It is also observed that higher thermal conductivity（TC） and flexural strength will be obtained with the addition of SiC particles.Meanwhile,coefficient of thermal expansion（CTE） changes smaller than TC.Models for predicting thermal properties were also discussed.Equivalent effective conductivity（EEC） was proposed to make H-J model suitable for hybrid particles and multimodal particle size distribution.展开更多
The Cu/Invar composites of 40% Cu were prepared by powder metallurgy, and the composites were rolled with 70% reduction and subsequently annealed at 750 ℃. Phases, microstructures and properties of the composites wer...The Cu/Invar composites of 40% Cu were prepared by powder metallurgy, and the composites were rolled with 70% reduction and subsequently annealed at 750 ℃. Phases, microstructures and properties of the composites were then studied. After that, the amount of a-Fe（Ni,Co） in the composites is reduced, because a-Fe（Ni,Co） partly transfers into y-Fe（Ni,Co） through the diffusion of the Ni atoms into a-Fe（Ni,Co） from Cu. When the rolling reduction is less than 40%, the deformation of Cu takes place, resulting in the movement of the Invar particles and the seaming of the pores. When the rolling reduction is in the range from 40% to 60%, the deformations of Invar and Cu occur simultaneously to form a streamline structure. After rolling till 70% and subsequent annealing, the Cu/Invar composites have fine comprehensive properties with a relative density of 98.6%, a tensile strength of 360 MPa, an elongation rate of 50%, a thermal conductivity of 25.42 W/（m.K） （as-tested） and a CTE of 10.79× 10-6/K （20-100 ℃）.展开更多
30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the co...30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the composites were investigated.The results indicated that interfacial reactions were inhibited during SPS because no Al4C3 was detected.Moreover,the agglomeration of the GNFs increased,and the distribution orientation of the GNFs decreased with increasing the GNF content.The relative density,bending strength,and coefficient of thermal expansion(CTE)of the composites decreased,while the thermal conductivity(TC)in the X−Y direction increased.As the sintering pressure increased,the GNFs deagglomerated and were distributed preferentially in the X−Y direction,which increased the relative density,bending strength and TC,and decreased the CTE of the composites.The 50wt.%GNFs/6061Al matrix composite sintered at 610℃ under 55 MPa demonstrated the best performance,i.e.,bending strength of 72 MPa,TC and CTE(RT−100℃)of 254 W/(m·K)and 8.5×10^(−6)K^(−1)in the X−Y direction,and 55 W/(m·K)and 9.7×10^(−6)K^(−1)in the Z direction,respectively.展开更多
Based on the research of modem electronic packaging materials, thixo-forming technology was used to fabricate electronic packaging shell. The process of thixo-extrusion with SiCp/A356 composites was simulated by the f...Based on the research of modem electronic packaging materials, thixo-forming technology was used to fabricate electronic packaging shell. The process of thixo-extrusion with SiCp/A356 composites was simulated by the finite element software DEFORM-3D, then the flow velocity field, equivalent strain field and temperature field were analyzed. The electronic packaging shell was manufactured by extrusion according to the results from numerical simulation. The results show that thixo-forming technology can be used in producing electronic package shell with SiCp/A356 composites, and high volume fraction of SiCp with homogeneous distribution can be achieved, being in agreement with the requirements of electronic packaging materials.展开更多
The electronic packaging shell with high silicon carbide aluminum-base composites was prepared by semi-solid thixoforming technique. The flow characteristic of the Si C particulate was analyzed. The microstructures of...The electronic packaging shell with high silicon carbide aluminum-base composites was prepared by semi-solid thixoforming technique. The flow characteristic of the Si C particulate was analyzed. The microstructures of different parts of the shell were observed by scanning electron microscopy and optical microscopy, and the thermophysical and mechanical properties of the shell were tested. The results show that there exists the segregation phenomenon between the Si C particulate and the liquid phase during thixoforming, the liquid phase flows from the shell, and the Si C particles accumulate at the bottom of the shell. The volume fraction of Si C decreases gradually from the bottom to the walls. Accordingly, the thermal conductivities of bottom center and walls are 178 and 164 W·m-1·K-1, the coefficients of thermal expansion(CTE) are 8.2×10-6 and 12.6×10-6 K-1, respectively. The flexural strength decreases slightly from 437 to 347 MPa. The microstructures and properties of the shell show gradient distribution.展开更多
Recent studies have revealed that concrete can be used as a media to contain As （arsenic） removed from drinking water. Concrete, which is a composite material, has been effective in solidifying hazardous wastes and ...Recent studies have revealed that concrete can be used as a media to contain As （arsenic） removed from drinking water. Concrete, which is a composite material, has been effective in solidifying hazardous wastes and contaminated soils. A research project was conducted to study the effects of uncontaminated soil and arsenic contaminated soil on the microstructure of concrete to qualitatively define the mechanisms of the encapsulation of soils containing inorganic material such as arsenic by application of solidification/stabilization technique. This research paper focused on studying the surface morphology of RPC （reactive powder concrete） containing soil.展开更多
A facile and scalable approach to synthesize silicon composite anodes has been developed by encapsulating Si particles via in situ polymerization and carbonization of phloroglucinol-formaldehyde gel, followed by incor...A facile and scalable approach to synthesize silicon composite anodes has been developed by encapsulating Si particles via in situ polymerization and carbonization of phloroglucinol-formaldehyde gel, followed by incorporation of graphene nanoplatelets. As a result of its structural integrity, high packing density and an intimate electrical contact consolidated by the conductive networks, the composite anode yielded excellent electrochemical performance in terms of charge storage capability, cycling life and coulombic efficiency. A half cell achieved reversible capacities of 1,600 mAh·g-1 and 1,000 mAh·g-1 at 0.5 A·g-1 and 2.1 A·g-1, respectively, while retaining more than 70% of the initial capacities over 1,000 cycles. Complete lithium-ion pouch cells coupling the anode with a lithium metal oxide cathode demonstrated excellent cycling performance and energy output, representing significant advance in developing Si-based electrode for practical application in high-performance lithium-ion batteries.展开更多
基金the financial support provided by the National Natural Science Foundation of China(No.52274369)the Science and Technology Program of Hunan Province,China(No.2020GK2044)。
文摘The thermal conductivity of Cu/Kovar composites was improved by suppressing element diffusion at the interfaces through the formation of FeWO_(4)coating on the Kovar particles via vacuum deposition.Cu matrix composites reinforced with unmodified(Cu/Kovar)and modified Kovar(Cu/Kovar@)particles were prepared by hot pressing.The results demonstrate that the interfaces of Cu/FeWO_(4)and FeWO_(4)/Kovar in the Cu/Kovar@composites exhibit strong bonding,and no secondary phase is generated.The presence of FeWO_(4)impedes interfacial diffusion within the composite,resulting in an increase in grain size and a decrease in dislocation density.After surface modification of the Kovar particle,the thermal conductivity of Cu/Kovar@composite is increased by 110%from 40.6 to 85.6 W·m^(-1)·K^(-1).Moreover,the thermal expansion coefficient of the Cu/Kovar@composite is 9.8×10^(-6)K^(-1),meeting the electronic packaging requirements.
基金Project (60776019) supported by the National Natural Science Foundation of ChinaProject (61-TP-2010) supported by the Research Fund of the State Key Laboratory of Solidification Processing (NWPU),China
文摘The Al/Si/SiC composites with medium volume fraction for electronic packaging were fabricated by gas pressure infiltration.On the premise of keeping the machinability of the composites,the silicon carbide particles,which have the similar size with silicon particles（average 13 μm）,were added to replace silicon particles of same volume fraction,and microstructure and properties of the composites were investigated.The results show that reinforcing particles are distributed uniformly and no apparent pores are observed in the composites.It is also observed that higher thermal conductivity（TC） and flexural strength will be obtained with the addition of SiC particles.Meanwhile,coefficient of thermal expansion（CTE） changes smaller than TC.Models for predicting thermal properties were also discussed.Equivalent effective conductivity（EEC） was proposed to make H-J model suitable for hybrid particles and multimodal particle size distribution.
文摘The Cu/Invar composites of 40% Cu were prepared by powder metallurgy, and the composites were rolled with 70% reduction and subsequently annealed at 750 ℃. Phases, microstructures and properties of the composites were then studied. After that, the amount of a-Fe（Ni,Co） in the composites is reduced, because a-Fe（Ni,Co） partly transfers into y-Fe（Ni,Co） through the diffusion of the Ni atoms into a-Fe（Ni,Co） from Cu. When the rolling reduction is less than 40%, the deformation of Cu takes place, resulting in the movement of the Invar particles and the seaming of the pores. When the rolling reduction is in the range from 40% to 60%, the deformations of Invar and Cu occur simultaneously to form a streamline structure. After rolling till 70% and subsequent annealing, the Cu/Invar composites have fine comprehensive properties with a relative density of 98.6%, a tensile strength of 360 MPa, an elongation rate of 50%, a thermal conductivity of 25.42 W/（m.K） （as-tested） and a CTE of 10.79× 10-6/K （20-100 ℃）.
基金financial support from the International Science&Technology Cooperation Program of China(No.2014DFA50860)。
文摘30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the composites were investigated.The results indicated that interfacial reactions were inhibited during SPS because no Al4C3 was detected.Moreover,the agglomeration of the GNFs increased,and the distribution orientation of the GNFs decreased with increasing the GNF content.The relative density,bending strength,and coefficient of thermal expansion(CTE)of the composites decreased,while the thermal conductivity(TC)in the X−Y direction increased.As the sintering pressure increased,the GNFs deagglomerated and were distributed preferentially in the X−Y direction,which increased the relative density,bending strength and TC,and decreased the CTE of the composites.The 50wt.%GNFs/6061Al matrix composite sintered at 610℃ under 55 MPa demonstrated the best performance,i.e.,bending strength of 72 MPa,TC and CTE(RT−100℃)of 254 W/(m·K)and 8.5×10^(−6)K^(−1)in the X−Y direction,and 55 W/(m·K)and 9.7×10^(−6)K^(−1)in the Z direction,respectively.
基金Project(2007AA03Z119) supported by the National High-tech Research and Development Program of ChinaProjects(2102029,2072012) supported by the Natural Science Foundation of Beijing,China
文摘Based on the research of modem electronic packaging materials, thixo-forming technology was used to fabricate electronic packaging shell. The process of thixo-extrusion with SiCp/A356 composites was simulated by the finite element software DEFORM-3D, then the flow velocity field, equivalent strain field and temperature field were analyzed. The electronic packaging shell was manufactured by extrusion according to the results from numerical simulation. The results show that thixo-forming technology can be used in producing electronic package shell with SiCp/A356 composites, and high volume fraction of SiCp with homogeneous distribution can be achieved, being in agreement with the requirements of electronic packaging materials.
文摘The electronic packaging shell with high silicon carbide aluminum-base composites was prepared by semi-solid thixoforming technique. The flow characteristic of the Si C particulate was analyzed. The microstructures of different parts of the shell were observed by scanning electron microscopy and optical microscopy, and the thermophysical and mechanical properties of the shell were tested. The results show that there exists the segregation phenomenon between the Si C particulate and the liquid phase during thixoforming, the liquid phase flows from the shell, and the Si C particles accumulate at the bottom of the shell. The volume fraction of Si C decreases gradually from the bottom to the walls. Accordingly, the thermal conductivities of bottom center and walls are 178 and 164 W·m-1·K-1, the coefficients of thermal expansion(CTE) are 8.2×10-6 and 12.6×10-6 K-1, respectively. The flexural strength decreases slightly from 437 to 347 MPa. The microstructures and properties of the shell show gradient distribution.
文摘Recent studies have revealed that concrete can be used as a media to contain As （arsenic） removed from drinking water. Concrete, which is a composite material, has been effective in solidifying hazardous wastes and contaminated soils. A research project was conducted to study the effects of uncontaminated soil and arsenic contaminated soil on the microstructure of concrete to qualitatively define the mechanisms of the encapsulation of soils containing inorganic material such as arsenic by application of solidification/stabilization technique. This research paper focused on studying the surface morphology of RPC （reactive powder concrete） containing soil.
文摘A facile and scalable approach to synthesize silicon composite anodes has been developed by encapsulating Si particles via in situ polymerization and carbonization of phloroglucinol-formaldehyde gel, followed by incorporation of graphene nanoplatelets. As a result of its structural integrity, high packing density and an intimate electrical contact consolidated by the conductive networks, the composite anode yielded excellent electrochemical performance in terms of charge storage capability, cycling life and coulombic efficiency. A half cell achieved reversible capacities of 1,600 mAh·g-1 and 1,000 mAh·g-1 at 0.5 A·g-1 and 2.1 A·g-1, respectively, while retaining more than 70% of the initial capacities over 1,000 cycles. Complete lithium-ion pouch cells coupling the anode with a lithium metal oxide cathode demonstrated excellent cycling performance and energy output, representing significant advance in developing Si-based electrode for practical application in high-performance lithium-ion batteries.
