Cu matrix composite reinforced with 10%（volume fraction） carbon nanotubes（CNTs/Cu） and pure Cu bulk were prepared by powder metallurgy techniques under the same consolidation processing condition.The effect of ele...Cu matrix composite reinforced with 10%（volume fraction） carbon nanotubes（CNTs/Cu） and pure Cu bulk were prepared by powder metallurgy techniques under the same consolidation processing condition.The effect of electrical current on tribological property of the materials was investigated by using a pin-on-disk friction and wear tester.The results show that the friction coefficient and wear rate of CNTs/Cu composite as well as those of pure Cu bulk increase with increasing the electrical current without exception,and the effect of electrical current is more obvious on tribological property of pure Cu bulk than on that of CNTs/Cu composite;the dominant wear mechanisms are arc erosion wear and plastic flow deformation,respectively;CNTs can improve tribological property of Cu matrix composites with electrical current.展开更多
Casting-cold extrusion technology was presented to fabricate alttminum/copper clad composite, and copper tubes with different sketch sections were designed. The technology of aluminum/copper clad composite fabricated ...Casting-cold extrusion technology was presented to fabricate alttminum/copper clad composite, and copper tubes with different sketch sections were designed. The technology of aluminum/copper clad composite fabricated by casting-cold extrusion was simulated by DEFORM software using tubes with four arc grooves. The stress and strain in different deformation zones were analyzed. The groove size reduces gradually and the groove shape drives to triangle during the extrusion procedure. The maximum values of equivalent effective stress and radial stress appear in groove zones, and the maximum equivalent effective strain firstly is obtained also in groove zones. The grain size in groove zones is less than that in other zones. The experimental results are consistent with simulation results, which prove that the copper tubes with sketch section are favorable to the metallurgy bond of boundary interface between aluminum and copper.展开更多
Production of Cu-Cr/carbon nanotube （CNT） hybrid nano-composite by wet and dry milling processes at three different levels of milling energy was investigated in order to study the effect of milling energy in two dif...Production of Cu-Cr/carbon nanotube （CNT） hybrid nano-composite by wet and dry milling processes at three different levels of milling energy was investigated in order to study the effect of milling energy in two different media on dispersion of CNTs, and preparation of the nano-composite. The structural evolution and solid solution formation were evaluated by X-ray diffraction technique. The microstructure was characterized by scanning electron microscopy and transmission electron microscopy. Also, the mechanical properties were measured by microhardness test. The mean crystallite size was in the range of 20-63 nm depending on milling medium and energy. CNTs dispersion is a function of milling energy. According to FESEM images and microhardness results, it can be concluded that wet milling is more applicable in dispersing CNTs homogeneously in comparison to dry milling. It was also found that wet milling at higher milling energies can be a beneficial method of producing the homogeneous hybrid nano-composite with the least damages introducing on CNTs because of the higher microhardness which can be attributed to better dispersion of less damaged CNTs. Compared with crystallite size changes, CNTs dispersion and damages were considerably more effective on hardness.展开更多
The main objective of this study is to enhance the strength of CNTs （carbon nanotubes） which reinforced AI matrix composites by introducing an appropriate amount of Copper（Cu） into the composite material. AI-Cu/MW...The main objective of this study is to enhance the strength of CNTs （carbon nanotubes） which reinforced AI matrix composites by introducing an appropriate amount of Copper（Cu） into the composite material. AI-Cu/MWCNTs （multi-walled carbon nanotubes） nanocomposites were produced via compaction, sintering and hot extrusion process of AI-Cu/MWCNTs powders, which were fabricated by a conventional ball mill process with AI powders and Cu-MWCNTs composite powders which were synthesized by molecular level mixing technique. Also the change of mechanical properties with different content ratio of Cu/MWCNT composite powders in A1 matrix is analyzed. It is found that the addition of the proper Cu/MWCNTs powders which are well distributed in AI matrix leads to high mechanical stiffness. The 2 wt% Cu/MWCNTs reinforced A1 composites which exhibited 3.2 times higher tensile strength and 4.4 times higher yield strength than pure AI.展开更多
基金Project(2007CB607603)supported by the National Basic Research Program of China
文摘Cu matrix composite reinforced with 10%（volume fraction） carbon nanotubes（CNTs/Cu） and pure Cu bulk were prepared by powder metallurgy techniques under the same consolidation processing condition.The effect of electrical current on tribological property of the materials was investigated by using a pin-on-disk friction and wear tester.The results show that the friction coefficient and wear rate of CNTs/Cu composite as well as those of pure Cu bulk increase with increasing the electrical current without exception,and the effect of electrical current is more obvious on tribological property of pure Cu bulk than on that of CNTs/Cu composite;the dominant wear mechanisms are arc erosion wear and plastic flow deformation,respectively;CNTs can improve tribological property of Cu matrix composites with electrical current.
文摘Casting-cold extrusion technology was presented to fabricate alttminum/copper clad composite, and copper tubes with different sketch sections were designed. The technology of aluminum/copper clad composite fabricated by casting-cold extrusion was simulated by DEFORM software using tubes with four arc grooves. The stress and strain in different deformation zones were analyzed. The groove size reduces gradually and the groove shape drives to triangle during the extrusion procedure. The maximum values of equivalent effective stress and radial stress appear in groove zones, and the maximum equivalent effective strain firstly is obtained also in groove zones. The grain size in groove zones is less than that in other zones. The experimental results are consistent with simulation results, which prove that the copper tubes with sketch section are favorable to the metallurgy bond of boundary interface between aluminum and copper.
基金The financial supports of this study by the Iran National Science Foundation (project No: 92013440)Iran Nanotechnology Initiative Council
文摘Production of Cu-Cr/carbon nanotube （CNT） hybrid nano-composite by wet and dry milling processes at three different levels of milling energy was investigated in order to study the effect of milling energy in two different media on dispersion of CNTs, and preparation of the nano-composite. The structural evolution and solid solution formation were evaluated by X-ray diffraction technique. The microstructure was characterized by scanning electron microscopy and transmission electron microscopy. Also, the mechanical properties were measured by microhardness test. The mean crystallite size was in the range of 20-63 nm depending on milling medium and energy. CNTs dispersion is a function of milling energy. According to FESEM images and microhardness results, it can be concluded that wet milling is more applicable in dispersing CNTs homogeneously in comparison to dry milling. It was also found that wet milling at higher milling energies can be a beneficial method of producing the homogeneous hybrid nano-composite with the least damages introducing on CNTs because of the higher microhardness which can be attributed to better dispersion of less damaged CNTs. Compared with crystallite size changes, CNTs dispersion and damages were considerably more effective on hardness.
文摘The main objective of this study is to enhance the strength of CNTs （carbon nanotubes） which reinforced AI matrix composites by introducing an appropriate amount of Copper（Cu） into the composite material. AI-Cu/MWCNTs （multi-walled carbon nanotubes） nanocomposites were produced via compaction, sintering and hot extrusion process of AI-Cu/MWCNTs powders, which were fabricated by a conventional ball mill process with AI powders and Cu-MWCNTs composite powders which were synthesized by molecular level mixing technique. Also the change of mechanical properties with different content ratio of Cu/MWCNT composite powders in A1 matrix is analyzed. It is found that the addition of the proper Cu/MWCNTs powders which are well distributed in AI matrix leads to high mechanical stiffness. The 2 wt% Cu/MWCNTs reinforced A1 composites which exhibited 3.2 times higher tensile strength and 4.4 times higher yield strength than pure AI.
