SO_2与Fe_2O_3生成Fe(Ⅱ)(aq)和硫酸盐的复相反应机理

使用DR IFTS,XPS,HPLC和IC考察了常温、常压和氧气存在下SO2与Fe2O3的复相反应,结果表明,SO2在Fe2O3表面的反应活性与Fe2O3表面含水量密切相关,表面含水量增加有助于Fe(Ⅱ)(aq)和硫酸盐的生成.室温下(T=291 K,相对湿度68%),每毫克Fe2O3在30 m in内可消耗53.6μg SO2,生成12.6 ngFe(Ⅱ)(aq)和56.2μg SO42-.反应产物SO42-的浓度比Fe(Ⅱ)(aq)的浓度高3个数量级,表明在生成硫酸盐的复相反应中铁对SO2氧化具有非常高的催化活性.提出了Fe(Ⅱ)(aq)和硫酸盐的生成机理.

例析固体参与复相反应的平衡移动问题

通过对固体参与化学反应的平衡移动3个试题的详解,探讨了固-气相化学反应中平衡移动对气体平均相对分子量的影响、固-固相反应中压强因素对平衡移动方向的影响以及等效平衡模式处理固-气相化学反应中化学平衡问题的一般规律,有助于突破教学中的难点,起到举一反三的教学效果.

二氧化硫与大气颗粒物的复相反应研究

利用原位FTIR,XPS等手段研究了SO2与大气颗粒物及部分氧化物的复相反应,确认了表面反应产物,讨论了复相反应历程和表面反应机理.结果表明,SO2在大气颗粒物和氧化物表面发生吸收和氧化反应,表面产物为SO32-和SO42-.表面酸碱性是不同氧化物对SO2吸收和氧化能力有较大差异的主要原因,本实验条件下氧化物和大气颗粒物样品复相反应能力顺序为:Al2O3＞CaO>>SiO2,Fe2O3,大气颗粒物样品.

有关固体颗粒分散度与化学反应平衡常数关系的探讨

从表面化学的一道习题出发,探讨固体颗粒分散度与其化学反应平衡常数之间的关系,借助高度分散系统的热力学基本方程及化学反应平衡判据,推导出在一般性的固态纯物质与理想气体的复相反应中,是否考虑固体反应物分散度时两种平衡常数之间的定量关系式。

Properties of Self-recoverable Mechanoluminescence Phosphor Ca_(5)Ga_(6)O_(14)∶Eu^(3+) and Its Information Encryption Application

A novel self-recoverable mechanoluminescent phosphor Ca_(5)Ga_(6)O_(14)∶Eu^(3+) was developed by the high-tem-perature solid-state reaction method,and its luminescence properties were investigated.Ca_(5)Ga_(6)O_(14)∶Eu^(3+)can produce red mechanoluminescence,and importantly,it shows good repeatability.The mechanoluminescence of Ca_(5)Ga_(6)O_(14)∶Eu^(3+) results from the piezoelectric field generated inside the material under stress,rather than the charge carriers stored in the traps,which can be confirmed by the multiple cycles of mechanoluminescence tests and heat treatment tests.The mechanoluminescence color can be turned from red to green by co-doping varied concentrations of Tb^(3+),which may be meaningful for encrypted letter writing.The encryption scheme for secure communication was devised by harnessing mechanoluminescence patterns in diverse shapes and ASCII codes,which shows good encryption performance.The results suggest that the mechanoluminescence phosphor Ca_(5)Ga_(6)O_(14)∶Eu^(3+),Tb^(3+)may be applied to the optical information encryption.

Hydrogen production performance of the non⁃platinum⁃based MoS_(2)/CuS cathode in microbial electrolytic cells

MoS_(2)/CuS composite catalysts were successfully synthesized using a one-step hydrothermal method with sodium molybdate dihydrate,thiourea,oxalic acid,and copper nitrate trihydrate as raw materials.The hydrogen pro-duction performance of MoS_(2)/CuS prepared with different molar ratios of Mo to Cu precursors(n_(Mo)∶n_(Cu))as cathodic catalysts was investigated in the two-chamber microbial electrolytic cell(MEC).X-ray diffraction(XRD),X-ray pho-toelectron spectroscopy(XPS),scanning electron microscopy(SEM),transmission electron microscope(TEM),linear scanning voltammetry(LSV),electrochemical impedance analysis(EIS),and cyclic voltammetry(CV)were used to characterize the synthesized catalysts for testing and analyzing the hydrogen-producing performance.The results showed that the hydrogen evolution performance of MoS_(2)/CuS-20%(nMo∶nCu=5∶1)was better than that of platinum(Pt)mesh,and the hydrogen production rate of MoS_(2)/CuS-20%as a cathode in MEC was(0.2031±0.0237)m^(3)_(H_(2))·m^(-3)·d^(-1) for 72 h at an applied voltage of 0.8 V,which was slightly higher than that of Pt mesh of(0.1886±0.0134)m^(3)_(H_(2))·m^(-3)·d^(-1).The addition of a certain amount of CuS not only regulates the electron transfer ability of MoS_(2) but also increases the density of active sites.

Microstructure and ablation behavior of Zr-based ultra-high-temperature gradient composites

To obtain high-performance Zr-based ultra-high-temperature composites,Zr-based ultra-high-temperature gradient composites were prepared by changing the laying method of the infiltrant via reactive melt infiltration.The effects of different infiltrant laying methods on the microstructure and ablative properties of Zr-based ultrahigh-temperature gradient composites were investigated.The results showed that the gradient structure of the Zr-based ultrahigh-temperature gradient composites differed when the composition ratio of the infiltrant was changed.When the thicknesses of the Zr/Mo/Si layers were 6/4/12 mm and 8/2/12 mm,the SiMoZrC solid solution content in the samples increased and decreased along the infiltration direction,respectively.The gradient samples were ablated in an oxyacetylene flame at 3000°C for 40 s.The ablation resistance of the sample was the highest when the infiltrant was a powder and the thickness of the Zr/Mo/Si layer was 6/4/12 mm.

Complexity and applicability analysis among OVM, GFM and FVDM models

The complexity and applicability of three relative car-following models are investigated and they are the optimal velocity model （OVM）,the generalized force model （GFM） and the full velocity difference model （FVDM）.The vehicle trajectory data used is collected from the digital pictures obtained at a 30-storey building near Ⅰ-80 freeway.Three different calibrating methods are used to estimate the model parameters and to study the relationships between model complexity and applicability from overall,inter-driver and intra-driver analysis.Results of the three methods of the OVM,GFM and FVDM show that the complexity and applicability are not consistent and the complicated models are not always superior to the simple ones in modeling car-following.The findings of this study can provide useful information for car-following behavior modeling.

Effects of Red Mud on the Remediation of Pb, Zn and Cd in Heavy Metal Contaminated Paddy Soil

[Objective] To study the remediation efficiency of red mud on Pb, Zn and Cd in the heavy metal contaminated paddy soil of mine area, to clarify its remediation mechanism and fertilizer efficiency on heavy metal contaminated soil. [Method] The soil incubation experiment was conducted to study the effect of red mud on the pH values and electrical conductivity （EC）, and the remediation efficiency of red mud on lead （Pb）, zinc （Zn） and cadmium （Cd） in heavy metal contaminated soil. [Result] Red mud addition reduced the content of exchangeable Pb, Zn and Cd in the soil significantly. Compared with the control, when incubated for 30, 60 and 90 d with the red mud dosage of 4% （W/W）, the exchangeable Pb content was decreased by 39.25%, 41.38% and 50.19%; exchangeable Zn content was decreased by 49.26%, 57.32% and 47.16%; and exchangeable Cd content was decreased by 19.53%, 24.06% and 25.70%, respectively. The application of red mud had significant impact on the share of Pb, Zn and Cd contents in five forms, and different amounts of red mud application all reduced the proportion of exchangeable Pb, Zn and Cd to the total Pb, Zn and Cd. In addition, the proportion of exchangeable Pb, Zn and Cd to total Pb, Zn and Cd decreased with the increasing amount of red mud addition. [Conclusion] The study provided references for reasonable application of red mud and reduction of heavy metal pollution in paddy soil.

Poly-Silicon Micromachined Switch

By using LPCVD SiO 2 and poly silicon as sacrificial layer and cantilever respectively,a poly silicon micromachined RF MEMS(radio frequency microelectronic mechanical system) switch is fabricated.During the fabrication process,the stress of poly silicon is released to prevent poly silicon membrane from bending,and the issue of compatibility between RF switch and IC process technology is also resolved.The low residual tensile stress poly silicon cantilever is obtained by the optimization.The switch is tested,and the preliminary test results show:the pull down voltage is 89V,and the switch speed is about 5μs.The switch provides the potential to build a new fully monolithic integrated RF MEMS for radar and communications applications.

皮革真空湿加工的研究与分析

论述了皮革真空加工的工艺研究及其生产潜在性 ,并从真空机制和复相反应动力学角度 ,对研究结果进行了分析与讨论。

Mechanism for thermite reactions of aluminum/iron-oxide nanocomposites based on residue analysis

Sol-gel method was employed to combine Al and iron-oxide to form nanocomposites （nano-Al/xero-Fe2O3 and micro-Al/xero-Fe2O3）. SEM, EDS and XRD analyses were used to characterize the nanocomposites and the results indicated that nano-Al and micro-Al were compactly wrapped by amorphous iron-oxide nanoparticles （about 20 nm）, respectively. The iron-oxide showed the mass ratio of Fe to O as similar as that in Fe2O3. Thermal analyses were performed on two nanocomposites, and four simple mixtures （nano-Al＋xero-Fe2O3, nano-Al＋micro-Fe2O3, micro-Al＋xero-Fe2O3, and micro-Al＋micro-Fe2O3） were also analyzed. There were not apparent distinctions in the reactions of thermites fueled by nano-Al. For thermites fueled by micro-Al, the DSC peak temperatures of micro-Al/Xero-Fe2O3 were advanced by 68.1 ℃ and 76.8 ℃ compared with micro-Al＋xero-Fe2O3 and micro-Al＋micro-Fe2O3, respectively. Four thermites, namely, nano-Al/xero-Fe2O3, nano-Al＋micro-Fe2O3, micro-Al/xero-Fe2O3, and micro-Al＋micro-Fe2O3, were heated from ambient temperature to 1020 ℃, during which the products at 660 ℃ and 1020 ℃ were collected and analyzed by XRD. Crystals of Fe, FeAl2O4, Fe3O4,α-Fe2O3, Al,γ-Fe2O3, Al2.667O4, FeO andα-Al2O3 were indexed in XRD patterns. For each thermite, according to the specific products, the possible equations were given. Based on the principle of the minimum free energy, the most reasonable equations were inferred from the possible reactions.

Simulation of temperature and stress in 6061 aluminum alloy during online quenching process

The cooling curves of 6061 aluminum alloy were acquired through water quenching experiment. The heat transfer coefficient was accurately calculated based on the cooling curves and the law of cooling. The online quenching process of complex cross-section profile was dynamically simulated by the ABAQUS software. The results suggest that the heat transfer coefficient changes during online quenching process. Different parts of the profile have different cooling velocity, and it was verified by water quenching experiment. The maximum residual stress of the profile was predicted using FEM simulation based on ABAQUS software The relations between the temperature and stress were presented by analyzing the data of key points.

HIGH STRAIN RATE SU PERPLASTICITY IN SiCp REINFORCED AZ31 MAGNESIUM MATRIX COMPOSITE

Superplasticity of AZ 31 magnesium matrix composites reinforced with 10 vol% SiC（2 μm） particulate i s investigated at temperature range from 365℃ to 565℃ and strain rate from 2.0 8×10-3 to 5.21×10-1 s-1. The maximum total elongation of 228 % is obtained at a strain rate of 2.08×10-1 s-1. The strain rate se nsitivity exponent （m） higher than 0.3, is observed when the strain rate is high er than 10-1 s-1 at 525℃. Increasing the test temperature to 540℃, the maximum total elongation exceeding 195% is achieved at a higher strain rate of 5.21×10-1 s-1 than that at 525℃. SiC in AZ31/SiCp composite ca n fine the matrix grain size. Filament is observed on the fracture surface of th e specimens showing superplasticity.

Creep mechanism and creep constitutive model of aluminum silicate short-fiber-reinforced magnesium matrix composite

By the constant stress tensile creep test method, creep tests were performed on aluminum silicate short fiber-reinforced AZ91D magnesium matrix composite with volume fraction of 30% and its matrix alloy AZ91D under different temperatures and stresses. The results indicate that the composite and the matrix have the same true stress exponent and true activation energy for creep, which are 3 and 144.63 kJ/mol, respectively. The creep of the composite is controlled by the creep of its matrix, which is mainly the controlling of viscous slip of dislocation, and the controlling of grain boundary slippage as a supplement. The creep constitutive model obtained from the experiment data can well describe the creep deformation pattern of the composite.

On the Training Modes of Interdisciplinary and Application-oriented Talents of Business English

This paper focuses on the training modes of interdisciplinary and application-oriented talents of business English and the constructions of curriculum. In the light of our socialist market-oriented economy characteristics, the discussion proceeds, in theory and practice, by putting forward a relatively profound approach according to the trend in the demands for business English talents and to the operational patterns of business English discipline, with some suggestions about the training modes of interdisciplinary and application-oriented talents and the construction of curriculum.

Effect of CuO particle size on synthesis temperature and microstructure of Al_2O_(3p)-Al composites from Al-CuO system

Al2O3p-Al composites were synthesized using an in-situ reaction in the 80%Al-20%CuO （mass fraction） system. The effects of the CuO particle size on the synthesis temperature and microstructure of the composites were investigated by various methods. The results indicate that the CuO particle size has a significant effect on the temperature at which the complete reaction in the Al-CuO system occurs：the temperature is 200 ℃ lower in the Al-CuO system containing CuO particles with sizes less than 6μm than that containing CuO particles with sizes less than 100μm. The interfacial bonding between Al2O3 particles and Al is not complete when the temperature is below a critical value. The morphology of the Al2O3 particles varies from ribbon-like shape to near spherical shape when the temperature is above a critical value. These two critical temperatures are affected by the particle size of CuO, and the critical temperature of the sample containing CuO particles with sizes less than 6μm is 100 ℃ lower than that of the sample containing CuO particles with sizes less than 100μm.

RELAXATION BEHAVIOUR OF GFRP UNIDIRECTIONAL LAMINATES

In this paper two set of GFRP specimens are manufactured and tested to investigate the relaxation behaviour under cyclic loading in the longitudinal and transversel direction. The relaxation of GFRP unidirectional laminates is evident for both cyclic loadings. Under longitudinal cyclic loading the relaxation is dependent on the number of loading cycles. Under transverse loading the relaxation depends on the loading cycles as well as the time of loading. Two expressions are set up to describe the relaxation for the longitudinal and transverse loading, and the predictions agree well with the experimental data.

In-situ synthesis of Al_3Ti particles reinforced Al-based composite coating

Using titanium wires （99.5%, 200 μm in diameter） as a reactive source, an Al-based composite coating reinforced by titanium tri-aluminide （A13Ti） particles was fabricated by infiltration plus in-situ methods. According to the differential thermal analysis （DTA） curve, the reactive temperature between Ti wires and A1 matrix can be determined at 890 ℃. The obtained composite coatings were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and microhardness and wear test. The experimental results show that when holding period is 20 min at 890℃, the titanium wires react completely to in-situ synthesize Al3Ti particles, which presents blocky and strip-like states. The microhardness of in-situ synthesized Al3Ti particles is about 4.5 times that of the Al-matrix. Under the condition of dry sliding at 10 N load, compared with the unreinforced Al matrix, the composite coating fabricated with 20 min offers unique wear resistance behavior, and its wear mechanism is that the adhesive wear and abrasive wear coexist.

Effects of Oleanolic Acid on the Immune Complex Allergic Reaction and Inflammation

When oleanolic acid (OA) was administered ig before and after sensitization on d 1 to d 5 and d 11 to d 17,it had no apparent effect on Arthus reaction.When it was administered at 48,24 and 1 h before challenge,however,Arthus reaction was significantly inhibited.OA showed markedly suppressive effects on reversible passive Arthus reaction and leukocyte migratory response.It could significantly stabilize erythrocyte membrane,inhibit the swelling of the rat's hind paw induced by in- jecting mycostatin,reduce the acid phosphatase content in the inflammatory exudate,suppress the syn- thesis or release of PGE,histamine,LTB4 and kinin,and the phlogistic action of PGE_2,histamine,5- HT and kinin.In addition,it could decrease the content of malonyldialdehyde (MDA) in hepatic tissue of alcohol-intoxicated mice,and increase the activity of catalase (CAT) in hepatic tissue of mice.OA had no apparent effect on the activity of super-oxide dismutase (SOD) in rat serum,on the content of immune complex in serum of rat with Arthus reaction,on the phagocytosis of monocytc-macrophage system,on the clearance of enzyme-containing immune complex by macrophage,or on the activity of total complement.