棉油皂脚复浸回收中性油的工艺

棉油皂脚中中性油含量视不同工艺而异。间歇法生产工艺得到的棉油皂脚中性油含量一般在30％～40％，有的高达40％～50％。而“棉油皂脚复浸回收中性油工艺”可使中性油含量降到3％～5％，复浸后的皂脚经处理后可作为化工原料出售或进一步深加工。

对油脚复浸技术异议

目前,还有许多浸出制油厂家采用“油脚复浸技术”对油脚进行处理,并且,有的地方还作为一种新技术进行推广。可是,根据我们实地考查和查阅有关资料,得出的结论是:就目前大多数浸出制油厂家实际情况,采用油脚复浸技术是弊大于利,不可取的。因此,笔者要提醒浸出制油厂对该技术的应用要慎重。

棉籽皂脚复浸回收中性油工艺研究与实践

棉油皂脚中中性油含量视不同工艺而异.间歇法生产工艺得到的皂脚其中性油含量一般在30—40%,有的厂家高达40—50%.笔者根据棉籽皂脚的特点进行了“棉油皂脚复浸回收中性油工艺“的研究与实践,取得了良好的效果.采用此工艺可使棉油皂脚中性油含量降到3—5%,复浸的皂脚经处理后可作为化工原料出售或进一步深加工.

棉籽皂脚复浸回收中性油工艺的问题与探讨

油皂脚中中性油含量视不同工艺而异。间歇法生产工艺得到的皂脚其中性油含量一般在３０－４０％，有的厂家高达４０－５０％。笔者根据棉籽皂脚的特点进行了“棉油皂脚复浸回收中性油工艺”的研究与实践，取得了良好的效果。采用此工艺可使棉油脚中性油含量降到３—５％，复浸后的皂脚经处理后可作为化工原料出售或进一步深加工。

五号病强弱毒在传代细胞上产生蚀斑的研究

对五号病强弱毒在传代细胞上产生蚀斑的研究表明,强毒OK_5株大、中、小斑分别为8,5和2mm,且一般在接种后50h就能充分出斑,弱毒OM_2R_(39)株大、中、小斑分别为3.5,2和1mm,出斑时间在100h以后;用蚀斑测毒,强毒OK_5的蚀斑毒价高于弱毒OM_2R_(39)3.8倍。由此证明五号病强弱病毒有遗传本质的不同。

Optimization of copper extraction for bioleaching of complex Cu-polymetallic concentrate by moderate thermophiles

Effects of initial pH, temperature, liquid volume, rotation speed, galvanic interaction （pyrite ratio） and pulp density on bioleaching of complex Cu-polymetallic concentrate were investigated. The results indicated that the copper extraction at pH 1.5 was 1.5 and 1.4 times that at pH 1.0 and pH 2.0 respectively. The copper extraction obtained at 45 ℃ was 1236.8%higher than that at 50 ℃. With the increase of rotation speed or the decrease of liquid volume, copper extraction was improved obviously. Copper extraction was improved gradually with the increase of pyrite ratio. However, when the ratio was higher than 20.0%, no further increase in copper extraction was observed. And the statistically significant interactive effects on copper extraction were found between temperature and pH, and temperature and pyrite ratio.

彩钼铅矿清洁提取工艺研究

清洁工艺的建立并不总是新技术的发明,而往往是新技术和已有技术的正确筛选与合理组合。本文总结了NaOH-Na2S复碱浸出体系、2次沉钼和离子膜电解回收碱的3个工艺试验,与其他常规技术相组合,建立了彩钼铅矿的清洁提取工艺模式。在工业试验中表现了低消耗、低污染、高回收率,较好地实现了经济效益、社会效益与环境效益的统一,并通过具体过程诠释了清洁生产的基本理念和建立清洁工艺的思路。

甘草种子处理方法

应用增温复浸法和碾米法处理甘草种子,使甘草种子由自然出苗率不足20％提高到85-90％。这二种方法操作简便,易被药农接受,适宜于大面积种植甘草时进行种子处理。

Effect of ZrC-SiC content on microstructure and ablation properties of C/C composites

C/C-ZrC-SiC composites with different ZrC-SiC contents were fabricated by precursor infiltration and pyrolysis. The effect of ceramic content on the microstructure and ablation resistance was investigated. Both the C/C-SiC and C/C-ZrC-SiC composites exhibited good ablation resistance under the plasma flame above 2300℃. Withtheincreaseof ZrC content, a continuous oxide layer and a solid Zr-Si-O mesophase were formed during the ablation. And the structure of the formed oxides layer closely linked with the contents of ZrC-SiC ceramics. The solid ZrO2-ZrC and Zr-Si-O mesophase could increase the viscosity of SiO2 moderately and improve the anti-scouring ability. The continuous SiO2-ZrO2-ZrC-SiC layer would serve as a thermal and oxygen barrier for preventing the substratefrom further ablation. The C/C-ZrC-SiC composites with 27.2%ZrC and 7.56%SiC shows superior ablation resistance, and the mass and linear ablation rates are-3.51 mg/s and-1.88 μm/s, respectively.

Pyrolysis mechanism of ZrC precursor and fabrication of C/C-ZrC composites by precursor infiltration and pyrolysis

C/C-ZrC composites were prepared by precursor infiltration and pyrolysis using the organic zirconium as precursor.The conversion mechanisms of the precursors such as the thermal behavior,structural evolution,phase composition,microstructure,composition of the precursors and products were analyzed by thermal gravimetric analyzer,Fourier transform infrared spectrometer,X-ray diffraction and scanning electron microscope.The results indicate that the ZrC precursor transforms to inorganic ZrO2 from room temperature to 1200 ℃,then reduces to ZrC at 1600 ℃ through the carbothermal reduction reaction.The microstructure of the C/C-ZrC composites was also investigated.The composites exhibit an interesting structure,a coating composed of ZrC ceramic covers the exterior of the composite,and the ZrC ceramic is embedded in the pores of the matrix inside the composite.

Threshold pressure and infiltration behavior of liquid metal into fibrous preform

A dynamic measuring apparatus was developed to investigate the infiltration process of liquid metal into the fibrous preform. 10% （volume fraction） chopped carbon fiber preforms were infiltrated with magnesium alloy under different infiltration pressures. The threshold pressure and flow behavior of liquid metal infiltrating into the preforms were calculated and measured. The microstructure of obtained Ct4Mg composites was observed. The results indicate that the measured threshold pressure for infiltration was 0.048 MPa, which was larger than the calculated value. The infiltration rate increased with the increase of infiltration pressure, but the increase amplitude decreased gradually. The tiny pores in the composites could be eliminated by increasing the infiltration pressure. When the infiltration pressure rose to 0.6 MPa, high quality C1/Mg composite was obtained.

Interfacial reactions and bending strength of SiC/A356/FeNi50 composite fabricated by gas pressure infiltration

The SiC/A356/FeNi50 composite was fabricated by gas pressure infiltration. The interfacial region of the SiC/A356/FeNi50 composite consisted of FeNi50 reaction layer, A1 reaction layer and A1 alloy matrix. The main intermetallic compounds were （Fe,Ni）a（A1,Sih3 and （Fe,Ni）2（A1,Si）5 at the A1 reaction layer and FeNi50 reaction layer, respectively. The bending behavior versus different infiltration temperatures and holding times was also investigated. The bending strength at 670 ~C was the highest and close to the bending strength of A1 alloy （223 MPa）, and 46% of SIC/A356. The brittle intermetallic compounds existing at the interface induced the decreasing of the bending strength. The pores were reduced by adequate heating time due to the homogeneous temperature of preform, which was beneficial to improve the bending strength of the composite.

Leaching kinetics of low-grade copper ore containing calcium-magnesium carbonate in ammonia-ammonium sulfate solution with persulfate

The leaching kinetics of copper from low-grade copper ore was investigated in ammonia-ammonium sulfate solution with sodium persulfate. The effect parameters of stirring speed, temperature, particle size, concentrations of ammonia, ammonium sulfate and sodium persulfate were determined. The results show that the leaching rate is nearly independent of agitation above 300 r/min and increases with the increase of temperature, concentrations of ammonia, ammonium sulfate and sodium persulfate. The EDS analysis and phase quantitative analysis of the residues indicate that bornite can be dissolved by persulfate oxidization. The leaching kinetics with activation energy of 22.91 kJ/mol was analyzed by using a new shrinking core model （SCM） in which both the interfacial transfer and diffusion across the product layer affect the leaching rate. A semi-empirical rate equation was obtained to describe the leaching process and the empirical reaction orders with respect to the concentrations of ammonia, ammonium sulfate and sodium persulfate are 0.5, 1.2 and 0.5, respectively.

Effects of heat treatment on phase contents and mechanical properties of infiltrated B_4C/2024Al composites

The B4C/2024Al composites were successfully produced by pressureless infiltration method, and the effects of heat treatment on phase content and mechanical properties were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and mechanical properties testing. The results show that phases of BnC/2024Al composites include B4C, Al, Al3BC, AlB2 and Al2Cu. The phase species remain unchanged; however, the phase content of the composites changes significantly after heat treatment at the temperature of 660, 700, 800 or 900 ℃ for 12, 24 or 36 h. It is found that the heat treatment results in not only considerable enhancement in hardness, but also reduction in bending strength of the composites. Heat treatment at 800 ℃ for 36 h does best to hardness of the composites, while at 700 ℃ for 36 h it is the most beneficial to their comprehensive mechanical properties.

Effects of dip-coated BN interphase on mechanical properties of SiC_f/SiC composites prepared by CVI process

BN interphase was successfully synthesized on SiC fiber fabrics by dip-coating process using boric acid and urea as precursors under N2 atmosphere. The morphology of BN interphase was observed by SEM, and the structure was characterized by XRD and FT-IR spectra. The SiCf/SiC composites with dip-coated BN interphase were fabricated by chemical vapor infiltration （CVI） process, and the effects ofBN interphase on the mechanical properties of composites were investigated. The results show that the SiC fibers are fully covered by BN interphase with smooth surface and turbostratic structure （t-BN）, and the thickness is about 0.4 μm. The flexural strengths of SiCf/SiC composites with and without BN interphase are about 180 and 95 MPa, respectively. Compared with the as-received SiCf/SiC composites, the composites with BN interphase exhibit an obvious toughened fracture behavior. From the microstructural analysis, it can be confirmed that the BN interphase plays a key part in protecting the fibers from chemical attack during matrix infiltration and weakening interfacial bonding, which can improve the mechanical properties of SiCf/SiC composites remarkably.

Wear behavior and mechanism of B_4C reinforced Mg-matrix composites fabricated by metal-assisted pressureless infiltration technique

The B4C/Mg composites fabricated by metal-assisted pressureless infiltration technique were used as experimental material, and the wear behavior and mechanism of this material were studied. A pin-on-disc apparatus was used to evaluate the wear behavior where loads of 20, 40, 60 and 80 N, and a sliding velocity of 250 r/min were exerted. The results show that B4C/Mg composites possess superior wear resistance than pure Mg under various applied loads, and the content of Ti, as infiltration inducer, has an influence on the wear resistance of B4C/Mg composites. The dominant wear mechanism for pure Mg is abrasion, while that for B4C/Mg composites under low loads is adhesion and delamination. Under high loads, the wear mechanism of B4C/Mg composites can be attributed to thermal softening and melting or plastic deformation.

Bonding mechanism of X10CrNi18-8 with Ni/Al_2O_3 composite ceramic by pressureless infiltration

Abstract： An alloy steel/alumina composite was successfully fabricated by pressureless infiltration of X10CrNil8-8 steel melt on 30% （mass fraction） Ni-containing alumina based composite ceramic （Ni/Al2O3） at 1 600 ℃. The infiltration quality and interfacial bonding behavior were investigated by SEM, EDS, XRD and tensile tests. The results show that there is an obvious interfacial reaction layer between the alloying steel and the Ni/Al2O3 composite ceramic. The interfacial reactive products are （FexAly）3O4 intermetallic phase and （AlxCry）2O3 solid solution. The interracial bonding strength is as high as about 67.5 MPa. The bonding mechanism of X10CrNi 18-8 steel with the composite ceramic is that Ni inside the ceramic bodies dissolves into the alloy melt and transforms into liquid channels, consequently inducing the steel melt infiltrating and filling in the pores and the liquid channels. Moreover, the metallurgical bonding and interfacial reactive bonding also play a key role on the stability of the bonding interface.

Influence of B4C particle size on microstructure and damping capacities of(B_(4)C+Ti)/Mg composites

To study the influence of B4C particle size on the microstructure and damping capacities of(B_(4)C+Ti)/Mg composites,in situ reactive infiltration technique was utilized to prepare Mg-matrix composites.The microstructure,produced phases and damping capacities of the composites prepared with different particle size of B4C were characterized and analyzed.The results show that the reaction between B4C and Ti tends to be more complete when finer B_(4)C particle was used to prepare the composites.But the microstructure of the as-prepared composites is more homogenous when B4C and Ti have similar particle size.The strain-dependent damping capacities of(B_(4)C+Ti)/Mg composites improve gradually with the increase of strain amplitude,and composites prepared with coarser B4C particles tend to have higher damping capacities.The temperature-dependent damping capacities improve with increasing the measuring temperatures,and the kind of damping capacities of the composites prepared with 5mm B4C are inferior to those of coarser particles.The dominant damping mechanism for the strain-damping capacity is dislocation damping and plastic zone damping,while that for the temperature-damping capacity is interface damping or grain boundary damping.

Innovative Production of PCMs （Phase Change Materials） Preparation by Vacuum Impregnation： Mechanical Strength of Mortars Cement with Composite PCMs Content

An experimental investigation was conducted to study the efficiency of thermal insulation of composite PCMs （phase change materials） produced by vacuum impregnation process between paraffin （PCMs） and fly ash particles. DSC （differential scanning calorimeter） has been used to determine the thermal properties of latent heat of melting and heat capacity for composite PCMs. Vacuum impregnation pressure of 40 in.Hg, paraffin melting temperature of 90℃, vacuum time and impregnation time of paraffin of 30 min are the optimum condition of composite PCMs productions. The values of latent heat of melting and heat capacity are 74.00 J/g and 15.726 J/g.℃ for composite PCMs that produces by the optimum condition in vacuum impregnation process. Increasing the amount of composite PCMs replacing for cement in mortars causes the compressive strength, flexural strength and tensile strength reduction. Compressive strength, flexural strength and tensile strength of mortar with and without composite PCMs can be increased by the longer time of water curing for mortar specimens. Thermal conductivity （k） of mortar cement is reduced by increasing the amount of composite PCMs which replaced for cement in mortar plate compositions. Composite PCMs have the efficiency for thermal energy insulation when incorporated into the buildings. Therefore, this property of paraffin/fly ash composites PCMs can reduce the energy consumption for temperature control in the buildings.

Microstructure,mechanical properties and wear resistance of SiC_(p)/AZ91 composite prepared by vacuum pressure infiltration

SiC_(p)/AZ91 composites were prepared by vacuum pressure infiltration.The microstructure,mechanical properties and wear resistance of composite were studied.Results indicated that SiC particles were uniformly distributed in the metal matrix and had a good interface bonding with the metal matrix.Mg_(17)Al_(12) preferably precipitated near the SiC particles,and high-density dislocations were induced by the mismatch of the coefficient of thermal expansion(CTE)between the SiC particle and the AZ91 matrix,thereby accelerating the aging precipitation of the matrix.Compared with AZ91 alloy,the addition of SiC particles improves the hardness and compressive strength of the composite,which is mainly due to the load transfer strengthening and grain refinement strengthening mechanisms.Furthermore,a stable support surface-protecting matrix formed during the wear process because of the excellent wear resistance of SiC.