Repeated unidirectional bending （RUB） was carried out to improve the texture of commercial AZ31B magnesium alloy sheets. All specimens were prepared in the rolling direction. The forming limit diagrams （FLDs） of A...Repeated unidirectional bending （RUB） was carried out to improve the texture of commercial AZ31B magnesium alloy sheets. All specimens were prepared in the rolling direction. The forming limit diagrams （FLDs） of AZ31B magnesium alloy sheet were determined experimentally by conducting stretch-forming tests at room temperature, 100, 200 and 300 ℃ Compared with the as-received sheet, the lowest limited strain of AZ31B magnesium alloy sheet with tilted texture in the FLD increased by 79% at room temperature and 104% at 100 ℃. The texture also affected the extension of the forming limit curves （FLC） in the FLD. However, the FLCs of two kinds of sheets almost overlapped at temperature above 200 ℃. It can be concluded that the reduction of （0002） texture intensity is effective to the improvement of formability not only at room temperature but also at low-and-medium temperature. The effect of texture on FLDs becomes weak with increasing temperature.展开更多
The effect of the repeated unidirectional bending （RUB） process and annealing on the formability of magnesium alloy sheets was investigated. The RUB process and annealing treatments produce two effects on microstruc...The effect of the repeated unidirectional bending （RUB） process and annealing on the formability of magnesium alloy sheets was investigated. The RUB process and annealing treatments produce two effects on microstructure： grain coarsening and weakening of the texture. The sheet that underwent RUB and was annealed at 300 ℃exhibits the best formability owing to the reduction of the （0002） basal texture intensity, which results in low yield strength, large fracture elongation, small Lankford value （r-value） and large strain hardening exponent （n-value）. Compared with the as-received sheet, the coarse-grain sheet produced by RUB and annealing at 400 ℃ exhibits lower tensile properties but higher formability. The phenomenon is because the deformation twin enhanced by grain coarsening can accommodate the strain of thickness.展开更多
AZ61Mg alloy was multi directionally forged(MDFed) during decreasing temperature condition from 643 K to 483 K at a true strain rate of 3×10-3 s-1 up to cumulative strain of∑△ε=4.0 at maximum.A pass strain of...AZ61Mg alloy was multi directionally forged(MDFed) during decreasing temperature condition from 643 K to 483 K at a true strain rate of 3×10-3 s-1 up to cumulative strain of∑△ε=4.0 at maximum.A pass strain of△ε=0.8 was employed.While average grain size decreased gradually with increasing cumulative strain,the evolution of fine-grained structure strongly depended on the MDF temperature.Under the condition where the temperature was higher than the most adequate one,grain coarsening partially took place during MDF.In contrast,at lower temperature,inhomogeneous microstructure composed of the initial coarse and newly appeared fine grains was evolved.After straining over∑△ε=3.2(i.e.,over 4 passes of MDF) ,equiaxed ultrafine grains(UFGs) having average size of about and lower than 1μm were uniformly evolved.While the MDFed alloy to∑△ε=4.0 possessed relatively high hardness of HV 99,and it accepted further about 20%cold rolling almost without cracking.Because of the superior formability of the UFGed AZ61Mg alloy,the hardness was further easily raised to HV 120 by following cold rolling.展开更多
Stresses, particularly those at geometric discontinuities, can influence structural integrity of engineering components. Motivated by the prevalence of cutouts in components, the objective of this paper is to demonstr...Stresses, particularly those at geometric discontinuities, can influence structural integrity of engineering components. Motivated by the prevalence of cutouts in components, the objective of this paper is to demonstrate ability to stress analyze finite, circularly-perforated orthotropic composites whose external loading may be unknown. Recognizing difficulties in obtaining purely theoretical or numerical solutions, the paper presents a hybrid means of stress analyzing such structures. Individual stresses, including those on the edge of the hole, are obtained in a loaded finite graphite/epoxy composite tensile plate containing a round hole by processing measured values of a single displacement field with an Airy stress function in complex variables. Displacements are recorded by digital image correlation. Traction-free conditions are satisfied analytically at the edge of the hole using conformal mapping and analytic continuation. Stresses satisfy equilibrium and strains satisfy compatibility. Significant features of the technique include its wide applicability, it smooths the measured information, does not require knowing the applied loading, and the rigorous mechanics foundation by which strains are determined from measured displacements.展开更多
基金Project(CSTC2010AA4035)supported by Scientific and Technological Project of Chongqing Science and Technology Commission,ChinaProject(50504019)supported by the National Natural Science Foundation of China+1 种基金Project(CDJZR11130008)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(CDJXS10130001)supported by the Chongqing University Postgraduates'Science and Innovation Fund,China
文摘Repeated unidirectional bending （RUB） was carried out to improve the texture of commercial AZ31B magnesium alloy sheets. All specimens were prepared in the rolling direction. The forming limit diagrams （FLDs） of AZ31B magnesium alloy sheet were determined experimentally by conducting stretch-forming tests at room temperature, 100, 200 and 300 ℃ Compared with the as-received sheet, the lowest limited strain of AZ31B magnesium alloy sheet with tilted texture in the FLD increased by 79% at room temperature and 104% at 100 ℃. The texture also affected the extension of the forming limit curves （FLC） in the FLD. However, the FLCs of two kinds of sheets almost overlapped at temperature above 200 ℃. It can be concluded that the reduction of （0002） texture intensity is effective to the improvement of formability not only at room temperature but also at low-and-medium temperature. The effect of texture on FLDs becomes weak with increasing temperature.
基金Project(CSTC2010AA4035)supported by Scientific and Technological Project of Chongqing Science and Technology Commission,ChinaProject(50504019)supported by the National Natural Science Foundation of China+1 种基金Project(CDJZR11130008)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(CDJXS10130001)supported by the Chongqing University Postgraduates'Science and Innovation Fund,China
文摘The effect of the repeated unidirectional bending （RUB） process and annealing on the formability of magnesium alloy sheets was investigated. The RUB process and annealing treatments produce two effects on microstructure： grain coarsening and weakening of the texture. The sheet that underwent RUB and was annealed at 300 ℃exhibits the best formability owing to the reduction of the （0002） basal texture intensity, which results in low yield strength, large fracture elongation, small Lankford value （r-value） and large strain hardening exponent （n-value）. Compared with the as-received sheet, the coarse-grain sheet produced by RUB and annealing at 400 ℃ exhibits lower tensile properties but higher formability. The phenomenon is because the deformation twin enhanced by grain coarsening can accommodate the strain of thickness.
基金support given by the Light Metals Educational Foundation,Japan,and Ministry of Education,Culture,Sports and Technology,Japan,with Grant No.20560647
文摘AZ61Mg alloy was multi directionally forged(MDFed) during decreasing temperature condition from 643 K to 483 K at a true strain rate of 3×10-3 s-1 up to cumulative strain of∑△ε=4.0 at maximum.A pass strain of△ε=0.8 was employed.While average grain size decreased gradually with increasing cumulative strain,the evolution of fine-grained structure strongly depended on the MDF temperature.Under the condition where the temperature was higher than the most adequate one,grain coarsening partially took place during MDF.In contrast,at lower temperature,inhomogeneous microstructure composed of the initial coarse and newly appeared fine grains was evolved.After straining over∑△ε=3.2(i.e.,over 4 passes of MDF) ,equiaxed ultrafine grains(UFGs) having average size of about and lower than 1μm were uniformly evolved.While the MDFed alloy to∑△ε=4.0 possessed relatively high hardness of HV 99,and it accepted further about 20%cold rolling almost without cracking.Because of the superior formability of the UFGed AZ61Mg alloy,the hardness was further easily raised to HV 120 by following cold rolling.
文摘Stresses, particularly those at geometric discontinuities, can influence structural integrity of engineering components. Motivated by the prevalence of cutouts in components, the objective of this paper is to demonstrate ability to stress analyze finite, circularly-perforated orthotropic composites whose external loading may be unknown. Recognizing difficulties in obtaining purely theoretical or numerical solutions, the paper presents a hybrid means of stress analyzing such structures. Individual stresses, including those on the edge of the hole, are obtained in a loaded finite graphite/epoxy composite tensile plate containing a round hole by processing measured values of a single displacement field with an Airy stress function in complex variables. Displacements are recorded by digital image correlation. Traction-free conditions are satisfied analytically at the edge of the hole using conformal mapping and analytic continuation. Stresses satisfy equilibrium and strains satisfy compatibility. Significant features of the technique include its wide applicability, it smooths the measured information, does not require knowing the applied loading, and the rigorous mechanics foundation by which strains are determined from measured displacements.
