太阳能集能器自动跟踪装置

太阳能集能器自动跟踪装置是由传感器、方位角跟踪机构、高度角跟踪机构和自动控制装置组成。自动跟踪装置驱动太阳能集能器 ,使集能器的主光轴始终与太阳光线相平行。当太阳光线发生倾斜时 ,传感器输出倾斜信号 ,指示执行器动作调整太阳能集能器的角度 ,直到太阳能集能器对准太阳 ,实现自动跟踪太阳的目的。在阴天或太阳光辐照度低于工作照度时自动关机 ,太阳光辐照度达到工作照度时自动开机。该装置适用于聚光式太阳能集能器。

Experiment and numerical simulation on flow and heat transfer in all-glass evacuated tube solar collectors

The experimental study of natural convection in allglass evacuated tube solar collectors is performed through the experimental platform of the solar-assisted fuel cell system.The experimental facility includes solar collectors with different length and diameter tubes, different coating materials, and with / without guide plates, respectively. Threedimensional mathematical models on natural and forced convections in the solar collectors are established and the experimental data is validated by field synergy and entransy principles. The results of natural convection show that the water temperature increases and thermal efficiency decreases gradually with the evacuated tube length. The thermal efficiency increases when absorption rates increase from 0. 95 to 1. 0 and emission rates decrease from 0. 16 to 0. 06. The thermal efficiency of solar collectors is increased after being equipped with the guide plate, which is attributed to the disappearance of the mixed flowand the enhancement of the heat transfer at the bottom of the evacuated tube. The results of forced convertion indicate that the Reynolds, Nusselt and entransy increments of the horizontal double collectors are higher than those of the vertical single collector while the entransy dissipation is lower than that of the vertical single collector. It is concluded that the solar collectors with guide plates are suitable for natural convection while the double horizontal collectors are suitable for forced convection in the thermal field of solar-assisted fuel cell systems with lowand medium temperatures.

Improving performance of flat plate solar collector using nanofluid water/zinc oxide

In this article,the effect of using water/zinc oxide nanofluid as a working fluid on the performance of solar collector is investigated experimentally.The volumetric concentration of nanoparticles is 0.4%,and the particle size is 40 nm,and the mass flow rate of the fluid varies from 1 to 3 kg/min.For this experiment,a device has been prepared with appropriate measuring instruments whose energy source is solar radiation.The solar energy absorbed by the flat plate collector is absorbed by the nanofluid of water/zinc oxide.The nanofluid is pumped to the consumer,a heat exchanger,where it heats the water.The temperature,radiation level,flow rate,and pressure in different parts of the device were measured.The pressure drop and the heat transferred are the most important results of this experimental work.The ASHRAE standard is used to calculate efficiency.The results showed that the use of water/zinc oxide nanofluid increases the collector performance compared to water.For 1 kg/min of mass flow rate,the nanofluids have a 16% increase in efficiency compared to water.From the results,it can be concluded that the choice of optimum mass flow rate in both water and nanofluid cases increases efficiency.

Performance investigation of solar thermal collector with auxiliary heater for space heating

In this paper,the performance of a solar thermal system with a focus on space heating was investigated.A 70 m^(2) detached house was considered in the weather conditions of the city of Tehran,Iran.A thermosyphon solar water heater with a flat plate collector combined with an auxiliary electrical heater supplies the heating demand of the house.The proposed system was modeled and analyzed using TRNSYS software.In this regard,the TRNBuild module was employed for the building load calculation.The model has been simulated for one year of operation.The effects of the solar collector’s surface area and storage volume were assessed.The results show that for a solar collector with a 15 m^(2) surface area,the solar fraction is 0.29 in January,during which the solar radiation is the lowest.Using solar collectors of10 m^(2) and 5 m^(2) surface areas,the solar fraction falls to 0.23 and 0.14,respectively in January.Besides,two cases of 150 L and 300 L storage tanks are taken into account.Eventually,it is found that using a 15 m^(2) solar collector and a 150 L storage tank can appropriately provide the building’ s heating demand taking the thermal performance and economic aspects into consideration.

Solar air conditioning researches and demonstrations in China

This paper mainly shows the demonstration of solar air conditioning systems in China, which includes LiBr-H2O absorption cooling, silica gel-water adsorption chiller, desiccant cooling and hybrid integrated energy systems for buildings. The match of solar collector types and chiller types have been discussed and suggested.

Solar Desalination with Latent Heat Storage Materials and Solar Collector

Availability of clean water is going to become one of biggest demands of the country. Even though there arc various technologies available for purification of water harnessing solar energy fits the purpose for future problems. Distillation is one of many processes available for water purification, and solar energy is one of several forms of heat energy that can be used to energize this process. In this review a study is made to enhance the productivity of the solar stills by connecting solar still with latent heat storage and solar air heater in series and other factors like improving evaporation rate by maintaining Low depth, more exposure area, heat addition by solar collector and presence of latent heat storage material, which is a paraffin wax as a integral part of still. Latent heat storage is one of the most efficient ways of storing thermal energy. Unlike the sensible heat storage method, the latent heat storage method provides much higher storage density, with a smaller temperature difference between storing and releasing heat. Further augmentation of the yield by scraps, pebble, and sand are added.

Performance enhancement of filled-type solar collector with U-tube

In order to increase the efficiency of solar collector, a methodology is proposed based on the analysis of its influencing factors, such as thermal conductivity of filled layer, structure forms of filled layer and heat loss coefficient. The results of analysis show that the heat transfer between pipes in evacuated tube is one of the most important factors, which can lead to the decrease of the outlet temperature of working fluid. In order to eliminate the negative influence of the heat transfer between pipes, the hollow filled-type evacuated tube with U-tube(HUFET) was developed, and the heat transfer characteristics of HUFET were analyzed by theoretical and experimental studies. The results show that the thermal resistances decrease with the increase of the thermal conductivity of filled layer. When the thermal conductivity is over 10 W/(m·K), the change of thermal resistances is very little.Furthermore, the larger the thermal conductivity of filled layer, the less the rate of the energy transfer between the two pipes to the total energy transfer, which is between the absorber tube and the working fluid. There is a little difference between the efficiencies of HUFET and UFET, with the efficiency of HUFET 2.4% higher than that of UFET. Meanwhile, the validation of the model developed was confirmed by the experiment.

Effect of Distance between Double Glazing on the Performance of a Solar Thermal Collector Control

In this research paper, an attempt has been made to come across the effect of distance between double glazing on the efficiency of a solar thermal collector. Experiments were carded out on an active solar energy demonstration system （ET 200）. Commercial glass pane of 3 mm thick having the same dimensions as that of the apparatus was placed above the collector at a distance of 2 cm, 4 cm and 6 cm. Tests were done with and without the added glass. Experiments were performed for double glazing with two positions of the light meter. In one position, it was placed in the middle of the collector surface. While, in the other one, the light meter was placed in the middle of the added glass. To study the effect of double glazing on the performance of the solar collector ET 200, the correct position of the light meter was to place it exactly in the middle of the additional pane under the lamp. Double glazing does not enhance the performance of the solar collector because of the high resistance of the system glass air glass. The efficiency of double glazing solar collector decreases with the increasing the distance of the two separated glasses.

Solar Heater Technologies Selection Using Multi-criteria Analysis

Regarding sun＇s potential in Middle East and North Africa zone and particularly in Morocco, we focus our work on the development of the knowledge and information concerning the solar heaters for domestic applications, in order to help the industrial and the consumer to select an adaptive technology. As a result, a Moroccan mapping of solar water heating systems is presented in this work. This mapping concerns two technologies commonly used： the FPC （flat plate collectors） and the ETC （evacuated tubes ones）. It is based on three criteria： firstly, the efficiency of the STC （solar thermal collectors）; secondly, the economic aspect and at last, the reliability requirements. Based on these information, the multi-criteria outranking methodology PROMETHEE （preference ranking organization method for the enrichment evaluations） allows us to define an adequate solar heater technology linked with the climatic zoning of Morocco.

Thermal Performance Study of Three Models of Solar Air Heater Made of Concrete

An experimental study was conducted on three models of solar collectors having an absorber made of concrete designed and built in the TPL （Thermal Process Laboratory）. A sequence of tests was performed on these models for the two air circulation models （forced and natural） in order to compare their thermal performance. The results are presented in terms of useful energy, stored energy and thermal efficiency of each model.

Simulating the Performance of Solar Water Heating Systems

This paper presents a software for simulating the thermal performance of solar water heating systems. The implemented model computes the energy balance in the hot water storage tank in each time step along a simulation interval. Its input data are values from a typical meteorological year of a chosen location and the hot water load. The system components are the hot water storage tank and the solar collector. Firstly, the validation of the model is presented and then four solar water heating systems are simulated in four different cities along one year. The storage tank water hourly temperatures were obtained for a typical meteorological year and those values were compared with the values obtained by the widespread TRNSYS simulation software. The results obtained from this comparison were satisfactory.

Social Indicators in Preliminary Studies for the Installation of Solar Panels, Salta, Argentina

More than 10% of the population in Salta is regarded as rural. Many rural areas suffer a shortage of energy, and consequently, possibilities of social and economic development of the inhabitants become reduced. The activation of renewable energy sources in these areas presents inhabitants the advantages to generate their own energy. Dispersed rural communities create small electricity demands that are not considered by suppliers, because they are not profitable. Although thus far, feasibility analyses to install photovoltaic or thermal solar collectors are based on technical reasons, it seems more convenient that, in the future, projects for the installation of technology based on renewable energy should consider social indicators. As a preliminary step to field work is proposed in this paper using an equation that allows us to obtain a value of＂social index＂. With this analysis and the current survey accompanied by the local people, knowledge will be obtained of the real needs of these rural communities. The results show that there is a variation that would allow a classification or ordering of localities. To validate the results obtained is proposed as the next step to perform field work in each of the localities.

Analysis by Indicators Performance of the Conceptual Structures mCCHP-SE Using Renewable Energy Sources

This paper refers to an integrated mCCHP （micro-combined cooling heat and power） systems dedicated for isolated residents with energetic independence. The only energy sources are wood pellet and solar energy. The proposed trigeneration system is based on mCHP （micro-combined heat and power） unit with Stirling engine, photovoltaic panels, thermal solar collector and pellet boiler. The proposed mCCHP system utilizes the exceeding amount of heat in the summer for producing the necessary cooling. A residential building with known energy consumption is determined load curves that must be covered by mCCHP system. The paper analyzes four structures of trigeneration systems with thermal activation chiller and two structures of trigeneration systems with mechanical compression chiller. Performance indicators are determined based on energy balance equations for each variant. It compares the performances and establishes the best option.