Adaptive flight control technology, feedback linearization, model inversion theory are reviewed and the error dynamic characteristics are analyzed, and an adaptive on-line neural network attitude control system is pre...Adaptive flight control technology, feedback linearization, model inversion theory are reviewed and the error dynamic characteristics are analyzed, and an adaptive on-line neural network attitude control system is presented. The model inversion is under the hover condition. And the adaptive control law based on the neural network is designed to guarantee the boundedness of tracking error and control signals. Simulation results demonstrate that the nonlinear neural network augmented model inversion can self-adapt to the uncertainty and modeling errors of unmanned helicopters. Results are compared while the parameters of PD controller and robustness items are changed.展开更多
Taking the accelerometer installation errors into consideration, the attitude optimization algorithm of Gyro Free Inertial Meastement Unit （GFIMU） is studied in the high spinning condition in this paper. A ten-accel...Taking the accelerometer installation errors into consideration, the attitude optimization algorithm of Gyro Free Inertial Meastement Unit （GFIMU） is studied in the high spinning condition in this paper. A ten-accelerometer configuration is designed so as to establish a mathematical model to acquire the angular speeds in the case of installation errors. Precision of the algorithm is evaluated by using damping GaussNewton method. A large amotmt of sinmlation results show that ff the accelertlmter＇s angleinstallation errors main-tain small （〈5°）, the errors of attitude angles can be limited within ±1°. Hence, the algorithm has a great applicable value in engineering.展开更多
The semi-round rigid feet would cause position-posture deviation problem because the actual foothold position is hardly known due to the rolling effect of the semi-round rigid feet during the robot walking. The positi...The semi-round rigid feet would cause position-posture deviation problem because the actual foothold position is hardly known due to the rolling effect of the semi-round rigid feet during the robot walking. The position-posture deviation problem may harm to the stability and the harmony of the robot, or even makes the robot tip over and fail to walk forward. Focused on the position-posture deviation problem of multi-legged walking robots with semi-round rigid feet, a new method of position-posture closed-loop control is proposed to solve the position-posture deviation problem caused by semi-round rigid feet, based on the inverse velocity kinematics of the multi-legged walking robots. The position-posture closed-loop control is divided into two parts: the position closed-loop control and the posture closed-loop control. Thus, the position-posture control for the robot which is a tight coupling and nonlinear system is decoupled. Co-simulations of position-posture open-loop control and position-posture closed-loop control by MATLAB and ADAMS are implemented, respectively. The co-simulation results verify that the position-posture closed-loop control performs well in solving the position-posture deviation problem caused by semi-round rigid feet.展开更多
This paper presents an efficient robot calibration method with non-contact vision metrology. Using the coplanar pattern to calibrate camera made the active-vision-based end-effector pose measurement be a feasible and ...This paper presents an efficient robot calibration method with non-contact vision metrology. Using the coplanar pattern to calibrate camera made the active-vision-based end-effector pose measurement be a feasible and costeffective way. Kinematic parameter errors were linearized and identified through two-step procedure, thus the singular and non-linear condition was overcome. These errors were then compensated using inverse model method. The whole calibration process is flexible, easy to implement and prevents the error propagation from the earlier stages to the later ones. Calibration was performed on MOTOMAN SV3industrial robot. Experiment results show that the proposed method is easy to setup and with satisfactory accuracy.展开更多
A novel approach is proposed for correcting command points and compressing discrete axis commands into a C2 continuous curve.The relationship between values of rotation angles and tool posture errors is firstly analyz...A novel approach is proposed for correcting command points and compressing discrete axis commands into a C2 continuous curve.The relationship between values of rotation angles and tool posture errors is firstly analyzed.A segmentation method based on values of rotation angles and lengths of adjacent points is then used to subdivide these command points into accuracy regions and smoothness regions.Since tool center points generated by CAD/CAM system are usually lying in the space that is apart from the desired curve within a tolerance distance,and the corresponding tool orientation vector may change a lot while the trajectory length of the tool center point is quite small,directly machining with such points will lead to problems of coarse working shape and long machining time.A correction method for command points is implemented so that good processing effectiveness can be achieved.Also,the quintic spline is used for compressing discrete command points into a C2 continuous smooth curve.The machining experiment is finally conducted to demonstrate the effectiveness of the proposed algorithm.展开更多
文摘Adaptive flight control technology, feedback linearization, model inversion theory are reviewed and the error dynamic characteristics are analyzed, and an adaptive on-line neural network attitude control system is presented. The model inversion is under the hover condition. And the adaptive control law based on the neural network is designed to guarantee the boundedness of tracking error and control signals. Simulation results demonstrate that the nonlinear neural network augmented model inversion can self-adapt to the uncertainty and modeling errors of unmanned helicopters. Results are compared while the parameters of PD controller and robustness items are changed.
基金supported by National Key Laboratory for Electronic Measurement and Technology(No.9140C120401080C12)
文摘Taking the accelerometer installation errors into consideration, the attitude optimization algorithm of Gyro Free Inertial Meastement Unit （GFIMU） is studied in the high spinning condition in this paper. A ten-accelerometer configuration is designed so as to establish a mathematical model to acquire the angular speeds in the case of installation errors. Precision of the algorithm is evaluated by using damping GaussNewton method. A large amotmt of sinmlation results show that ff the accelertlmter＇s angleinstallation errors main-tain small （〈5°）, the errors of attitude angles can be limited within ±1°. Hence, the algorithm has a great applicable value in engineering.
基金Project(51221004)supported by the Science Fund for Creative Research Groups of National Natural Science Foundation of ChinaProject supported by the Program for Zhejiang Leading Team of S&T Innovation,China
文摘The semi-round rigid feet would cause position-posture deviation problem because the actual foothold position is hardly known due to the rolling effect of the semi-round rigid feet during the robot walking. The position-posture deviation problem may harm to the stability and the harmony of the robot, or even makes the robot tip over and fail to walk forward. Focused on the position-posture deviation problem of multi-legged walking robots with semi-round rigid feet, a new method of position-posture closed-loop control is proposed to solve the position-posture deviation problem caused by semi-round rigid feet, based on the inverse velocity kinematics of the multi-legged walking robots. The position-posture closed-loop control is divided into two parts: the position closed-loop control and the posture closed-loop control. Thus, the position-posture control for the robot which is a tight coupling and nonlinear system is decoupled. Co-simulations of position-posture open-loop control and position-posture closed-loop control by MATLAB and ADAMS are implemented, respectively. The co-simulation results verify that the position-posture closed-loop control performs well in solving the position-posture deviation problem caused by semi-round rigid feet.
文摘This paper presents an efficient robot calibration method with non-contact vision metrology. Using the coplanar pattern to calibrate camera made the active-vision-based end-effector pose measurement be a feasible and costeffective way. Kinematic parameter errors were linearized and identified through two-step procedure, thus the singular and non-linear condition was overcome. These errors were then compensated using inverse model method. The whole calibration process is flexible, easy to implement and prevents the error propagation from the earlier stages to the later ones. Calibration was performed on MOTOMAN SV3industrial robot. Experiment results show that the proposed method is easy to setup and with satisfactory accuracy.
基金supported by the National Key Basic Research and Development Projects under Grant No.2011CB302400
文摘A novel approach is proposed for correcting command points and compressing discrete axis commands into a C2 continuous curve.The relationship between values of rotation angles and tool posture errors is firstly analyzed.A segmentation method based on values of rotation angles and lengths of adjacent points is then used to subdivide these command points into accuracy regions and smoothness regions.Since tool center points generated by CAD/CAM system are usually lying in the space that is apart from the desired curve within a tolerance distance,and the corresponding tool orientation vector may change a lot while the trajectory length of the tool center point is quite small,directly machining with such points will lead to problems of coarse working shape and long machining time.A correction method for command points is implemented so that good processing effectiveness can be achieved.Also,the quintic spline is used for compressing discrete command points into a C2 continuous smooth curve.The machining experiment is finally conducted to demonstrate the effectiveness of the proposed algorithm.
