Material growth and device fabrication of the first 1.3μm quantum well （QW） edge emitting laser diodes in China are reported. Through the optimization of the molecular beam epitaxy （MBE） growth conditions and the...Material growth and device fabrication of the first 1.3μm quantum well （QW） edge emitting laser diodes in China are reported. Through the optimization of the molecular beam epitaxy （MBE） growth conditions and the tuning of the indium and nitrogen composition of the GalnNAs QWs, the emission wavelengths of the QWs can be tuned to 1.3μm. Ridge geometry waveguide laser diodes are fabricated. The lasing wavelength is 1.3μm under continuous current injection at room temperature with threshold current of 1kA/cm^2 for the laser diode structures with the cleaved facet mirrors. The output light power over 30mW is obtained.展开更多
Differences of gene expression between salinity_stressed and control rice ( Oryza sativa L. ssp. indica ) cultivar “Zhaiyeqing 8' were compared using differential display PCR (DD_PCR) technique. Sequence an...Differences of gene expression between salinity_stressed and control rice ( Oryza sativa L. ssp. indica ) cultivar “Zhaiyeqing 8' were compared using differential display PCR (DD_PCR) technique. Sequence analysis of one salt_inducible cDNA clone revealed that this clone represented a new member of rice translation elongation factor 1A (eEF1A) gene family and was tentatively named REF1A. Northern blot hybridization using REF1A fragment as a probe was performed to investigate the expression of rice translation elongation factor 1A gene in response to various environmental factors. It was observed that expression of the eEF1A gene in rice shoots was dramatically induced by salinity stress or exogenous application of abscisic acid (ABA). The induction of this gene by ABA stress occurred more quickly than that by salinity stress. In addition, expression of rice translation elongation factor 1A gene was also induced by drought (15% PEG6000), cold (4 ℃) or heat_shock (37 ℃) stresses. The results suggested that the induction of translation elongation factor 1A gene expression by environmental stresses might reflect the general adaptive response of rice plants to the adverse circumstances.展开更多
Highly stained InGaAs/GaAs Quantum Wells (QW) are grown by using molecular beam epitaxy.The room-temperature photoluminescence (PL) peak wavelength as long as 1160nm is obtained from QW with the In composition of 38% ...Highly stained InGaAs/GaAs Quantum Wells (QW) are grown by using molecular beam epitaxy.The room-temperature photoluminescence (PL) peak wavelength as long as 1160nm is obtained from QW with the In composition of 38% and the well width of 6 8nm.The full-width at half-maximum of the PL peak is 22meV,indicating a good quality.InGaAs/GaAs QW ridge-waveguide lasers with emission wavelength of 1120nm are demonstrated.For 100-μm-wide ridge-waveguide lasers with a cavity length of 800μm,the kink-free output power up to 200mW is achieved with the slope efficiency of 0 84mW/mA under the continue-wave operation.For 10μm-wide ridge-waveguide lasers,the lowest threshold current density of 450A/cm2 and the characteristic temperature of 90K are obtained.展开更多
The molecular beam epitaxial growth of high quality epilayers on （100） InP substrate using a valve phosphorous cracker cell over a wide range of P/In BEP ratio （2.0-7.0） and growth rate （0.437 and 0. 791μm/h）. ...The molecular beam epitaxial growth of high quality epilayers on （100） InP substrate using a valve phosphorous cracker cell over a wide range of P/In BEP ratio （2.0-7.0） and growth rate （0.437 and 0. 791μm/h）. Experimental results show that electrical properties exhibit a pronounced dependence on growth parameters,which are growth rate, P/In BEP ratio, cracker zone temperature, and growth temperature. The parameters have been optimized carefully via the results of Hall measurements. For a typical sample, 77K electron mobility of 4.57 × 10^4 cm^2/（V · s） and electron concentration of 1.55×10^15 cm^-3 have been achieved with an epilayer thickness of 2.35μm at a growth temperature of 370℃ by using a cracking zone temperature of 850℃.展开更多
Self-assembled In 0.35Ga 0.65As/GaAs quantum dots with low indium content are grown under different growth temperature and investigated using contact atomic force microscopy(AFM).In order to obtain high density ...Self-assembled In 0.35Ga 0.65As/GaAs quantum dots with low indium content are grown under different growth temperature and investigated using contact atomic force microscopy(AFM).In order to obtain high density and high uniformity of quantum dots,optimized conditions are concluded for MBE growth.Optimized growth conditions also compared with these of InAs/GaAs quantum dots.This will be very useful for InGaAs/GaAs QDs optoelectronic applications,such as quantum dots lasers and quantum dots infrared photodetectors.展开更多
Contacting mode atomic force microscopy (AFM) is used to measure the In 0.35 Ga 0.65 As/GaAs epilayer grown at low temperature (460℃).Unlike the normal layer by layer growth (FvdM mode) or self organized i...Contacting mode atomic force microscopy (AFM) is used to measure the In 0.35 Ga 0.65 As/GaAs epilayer grown at low temperature (460℃).Unlike the normal layer by layer growth (FvdM mode) or self organized islands growth (SK mode),samples grown under 460℃ are found to be large islands with atomic thick terraces.AFM measurements reveale near one monolayer high steps.This kind of growth is good between FvdM and SK growth modes and can be used to understand the evolution of strained epitaxy from FvdM to SK mode.展开更多
The effects of ion damage on Ga NAs/Ga As and Ga In NAs/Ga As quantum wells ( QWs) grown by plas- ma- assisted molecular beam epitaxy have been investigated. Itis found thation damage is a key factor affecting the q...The effects of ion damage on Ga NAs/Ga As and Ga In NAs/Ga As quantum wells ( QWs) grown by plas- ma- assisted molecular beam epitaxy have been investigated. Itis found thation damage is a key factor affecting the quality of Ga NAs and Ga In NAs QWs. Obvious appearance of pendello¨ sung fringes in X- ray diffraction pattern and remarkable im provement in the optical properties of the samples grown with ion removal magnets are observed.By removing nitrogen ions,the PL intensity of the Ga In NAs QW is improved so as to be comparable with that of Ga In As QW. The stronger is the magnetic field,the m ore obvious the PL intensity im provement would be.展开更多
Some results on the molecular-beam epitaxial growth of HgCdTe focusing on the requirements of the 3rd generation infrared focal plane arrays are described. Good uniformity is observed over 75mm HgCdTe epilayers,and th...Some results on the molecular-beam epitaxial growth of HgCdTe focusing on the requirements of the 3rd generation infrared focal plane arrays are described. Good uniformity is observed over 75mm HgCdTe epilayers,and the deviation in cutoff wavelength is within 0. 1μm at 80K. A variety of surface defects are observed and the formation mechanism is discussed. The average density of surface defects in 75mm HgCdTe epiluyers is found to be less than 300cm^-2. It is found that the surface sticking coefficient of As during HgCdTe growth is very low and is sensitive to growth temperature, being only -1 × 10^-4 at 170℃. The activation energy of As in HgCdTe was determined to be 19.5meV,which decreases as （Na - Nd）^1/3 with a slope of 3.1 × 10^-5 meV · cm. The diffusion coefficients of As in HgCdTe of 1.0 ± 0,9 × 10^-16,8 ± 3 × 10^- is, and 1.5 ± 0.9 × 10^-13 cm^2/s are obtained at temperatures of 240,380, and 440℃, respectively under Hg-saturated pressure. The MBE-grown HgCdTe is incorporated into FPA fabrications,and the preliminary results are presented.展开更多
The heterostructure of InAs/In0.52Al0.48As/InP is unique in that InAs wires instead of dots self-assemble in molecular beam epitaxy. These InAs wires have some distinctive features in their growth and structure. This ...The heterostructure of InAs/In0.52Al0.48As/InP is unique in that InAs wires instead of dots self-assemble in molecular beam epitaxy. These InAs wires have some distinctive features in their growth and structure. This paper summarizes the investigations of the growth and structural properties of InAs wires that have been performed in our laboratory recently.展开更多
Based on the 3D electron's radial wave function of Co 2+ free ion,a Nephelauxetic effect modifying factor to modify the radial wave function is introduced when Co 2+ cations are put into the crystal fie...Based on the 3D electron's radial wave function of Co 2+ free ion,a Nephelauxetic effect modifying factor to modify the radial wave function is introduced when Co 2+ cations are put into the crystal field of Zn 1-x Co x Se.With the modified wave functions,the optical transitions for Zn 1-x Co x Se crystals are calculated.Moreover,based on the first principle of physics,the influences of high pressure to the Nephelauxetic effect modifying factor is considered,and the high pressure blue shift for the Zn 1-x Co x Se crystal absorption spectra are calculated and a shift rate of d E /d p =0 45meV/GPa is obtained.展开更多
A different approach,using the molecular beam epitaxy (MBE)-grown ZnS-based Schottky photodiode technology,is applied to fabricate an 8×8 photodiode array.The micro-processing procedures of this photodiode array ...A different approach,using the molecular beam epitaxy (MBE)-grown ZnS-based Schottky photodiode technology,is applied to fabricate an 8×8 photodiode array.The micro-processing procedures of this photodiode array including standard photolithography,a number of metallisation,wet-chemical etching and SiO_2 deposition for insulation are developed.The detector is characterized to have a cutoff wavelength at 340 nm and the photo-responsivity measurements on the pixels result an ultraviolet (UV) response as high as 0.15 A/W,corresponding to an external quantum efficiency of 55% in the visible-blind spectral ranging from 400 down to 250nm.Imaging tests indicate that this array is able to capture the intensity profile of a given UV light source with reasonably good capability.展开更多
文摘Material growth and device fabrication of the first 1.3μm quantum well （QW） edge emitting laser diodes in China are reported. Through the optimization of the molecular beam epitaxy （MBE） growth conditions and the tuning of the indium and nitrogen composition of the GalnNAs QWs, the emission wavelengths of the QWs can be tuned to 1.3μm. Ridge geometry waveguide laser diodes are fabricated. The lasing wavelength is 1.3μm under continuous current injection at room temperature with threshold current of 1kA/cm^2 for the laser diode structures with the cleaved facet mirrors. The output light power over 30mW is obtained.
文摘Differences of gene expression between salinity_stressed and control rice ( Oryza sativa L. ssp. indica ) cultivar “Zhaiyeqing 8' were compared using differential display PCR (DD_PCR) technique. Sequence analysis of one salt_inducible cDNA clone revealed that this clone represented a new member of rice translation elongation factor 1A (eEF1A) gene family and was tentatively named REF1A. Northern blot hybridization using REF1A fragment as a probe was performed to investigate the expression of rice translation elongation factor 1A gene in response to various environmental factors. It was observed that expression of the eEF1A gene in rice shoots was dramatically induced by salinity stress or exogenous application of abscisic acid (ABA). The induction of this gene by ABA stress occurred more quickly than that by salinity stress. In addition, expression of rice translation elongation factor 1A gene was also induced by drought (15% PEG6000), cold (4 ℃) or heat_shock (37 ℃) stresses. The results suggested that the induction of translation elongation factor 1A gene expression by environmental stresses might reflect the general adaptive response of rice plants to the adverse circumstances.
文摘Highly stained InGaAs/GaAs Quantum Wells (QW) are grown by using molecular beam epitaxy.The room-temperature photoluminescence (PL) peak wavelength as long as 1160nm is obtained from QW with the In composition of 38% and the well width of 6 8nm.The full-width at half-maximum of the PL peak is 22meV,indicating a good quality.InGaAs/GaAs QW ridge-waveguide lasers with emission wavelength of 1120nm are demonstrated.For 100-μm-wide ridge-waveguide lasers with a cavity length of 800μm,the kink-free output power up to 200mW is achieved with the slope efficiency of 0 84mW/mA under the continue-wave operation.For 10μm-wide ridge-waveguide lasers,the lowest threshold current density of 450A/cm2 and the characteristic temperature of 90K are obtained.
文摘The molecular beam epitaxial growth of high quality epilayers on （100） InP substrate using a valve phosphorous cracker cell over a wide range of P/In BEP ratio （2.0-7.0） and growth rate （0.437 and 0. 791μm/h）. Experimental results show that electrical properties exhibit a pronounced dependence on growth parameters,which are growth rate, P/In BEP ratio, cracker zone temperature, and growth temperature. The parameters have been optimized carefully via the results of Hall measurements. For a typical sample, 77K electron mobility of 4.57 × 10^4 cm^2/（V · s） and electron concentration of 1.55×10^15 cm^-3 have been achieved with an epilayer thickness of 2.35μm at a growth temperature of 370℃ by using a cracking zone temperature of 850℃.
文摘Self-assembled In 0.35Ga 0.65As/GaAs quantum dots with low indium content are grown under different growth temperature and investigated using contact atomic force microscopy(AFM).In order to obtain high density and high uniformity of quantum dots,optimized conditions are concluded for MBE growth.Optimized growth conditions also compared with these of InAs/GaAs quantum dots.This will be very useful for InGaAs/GaAs QDs optoelectronic applications,such as quantum dots lasers and quantum dots infrared photodetectors.
文摘Contacting mode atomic force microscopy (AFM) is used to measure the In 0.35 Ga 0.65 As/GaAs epilayer grown at low temperature (460℃).Unlike the normal layer by layer growth (FvdM mode) or self organized islands growth (SK mode),samples grown under 460℃ are found to be large islands with atomic thick terraces.AFM measurements reveale near one monolayer high steps.This kind of growth is good between FvdM and SK growth modes and can be used to understand the evolution of strained epitaxy from FvdM to SK mode.
文摘The effects of ion damage on Ga NAs/Ga As and Ga In NAs/Ga As quantum wells ( QWs) grown by plas- ma- assisted molecular beam epitaxy have been investigated. Itis found thation damage is a key factor affecting the quality of Ga NAs and Ga In NAs QWs. Obvious appearance of pendello¨ sung fringes in X- ray diffraction pattern and remarkable im provement in the optical properties of the samples grown with ion removal magnets are observed.By removing nitrogen ions,the PL intensity of the Ga In NAs QW is improved so as to be comparable with that of Ga In As QW. The stronger is the magnetic field,the m ore obvious the PL intensity im provement would be.
文摘Some results on the molecular-beam epitaxial growth of HgCdTe focusing on the requirements of the 3rd generation infrared focal plane arrays are described. Good uniformity is observed over 75mm HgCdTe epilayers,and the deviation in cutoff wavelength is within 0. 1μm at 80K. A variety of surface defects are observed and the formation mechanism is discussed. The average density of surface defects in 75mm HgCdTe epiluyers is found to be less than 300cm^-2. It is found that the surface sticking coefficient of As during HgCdTe growth is very low and is sensitive to growth temperature, being only -1 × 10^-4 at 170℃. The activation energy of As in HgCdTe was determined to be 19.5meV,which decreases as （Na - Nd）^1/3 with a slope of 3.1 × 10^-5 meV · cm. The diffusion coefficients of As in HgCdTe of 1.0 ± 0,9 × 10^-16,8 ± 3 × 10^- is, and 1.5 ± 0.9 × 10^-13 cm^2/s are obtained at temperatures of 240,380, and 440℃, respectively under Hg-saturated pressure. The MBE-grown HgCdTe is incorporated into FPA fabrications,and the preliminary results are presented.
文摘The heterostructure of InAs/In0.52Al0.48As/InP is unique in that InAs wires instead of dots self-assemble in molecular beam epitaxy. These InAs wires have some distinctive features in their growth and structure. This paper summarizes the investigations of the growth and structural properties of InAs wires that have been performed in our laboratory recently.
文摘Based on the 3D electron's radial wave function of Co 2+ free ion,a Nephelauxetic effect modifying factor to modify the radial wave function is introduced when Co 2+ cations are put into the crystal field of Zn 1-x Co x Se.With the modified wave functions,the optical transitions for Zn 1-x Co x Se crystals are calculated.Moreover,based on the first principle of physics,the influences of high pressure to the Nephelauxetic effect modifying factor is considered,and the high pressure blue shift for the Zn 1-x Co x Se crystal absorption spectra are calculated and a shift rate of d E /d p =0 45meV/GPa is obtained.
文摘A different approach,using the molecular beam epitaxy (MBE)-grown ZnS-based Schottky photodiode technology,is applied to fabricate an 8×8 photodiode array.The micro-processing procedures of this photodiode array including standard photolithography,a number of metallisation,wet-chemical etching and SiO_2 deposition for insulation are developed.The detector is characterized to have a cutoff wavelength at 340 nm and the photo-responsivity measurements on the pixels result an ultraviolet (UV) response as high as 0.15 A/W,corresponding to an external quantum efficiency of 55% in the visible-blind spectral ranging from 400 down to 250nm.Imaging tests indicate that this array is able to capture the intensity profile of a given UV light source with reasonably good capability.
