The Mg-Sn alloys,with basal or prismatic Mg2Sn laths,were employed to reveal the effect of precipitate orientation on twinning behavior quantitatively.The Mg-5wt.%Sn alloys with basal or prismatic Mg2Sn were compresse...The Mg-Sn alloys,with basal or prismatic Mg2Sn laths,were employed to reveal the effect of precipitate orientation on twinning behavior quantitatively.The Mg-5wt.%Sn alloys with basal or prismatic Mg2Sn were compressed to study the twinning behaviors.Subsequently,an Orowan strengthening model was developed to quantitatively investigate the critical resolved shear stress(CRSS)increment of precipitates on twinning.The results revealed that the prismatic precipitates hindered the transfer and growth of tensile twins more effectively compared with the basal precipitates.The decreased proportion of tensile twins containing prismatic Mg2Sn might be attributed to a larger CRSS increment for tensile twins compared with that for basal precipitates.The obvious decreased twinning transfer in the alloy with prismatic Mg2Sn could be due to its higher geometrically necessary dislocation and enhanced CRSS of tensile twins.Notably,the prismatic precipitates have a better hindering effect on tensile twins during compression.展开更多
Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dyna...Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.展开更多
基金National Natural Science Foundation of China(Nos.52004227,U22A20187,52201106)the China Postdoctoral Science Foundation(No.2020M683240)+1 种基金the Key Area Research and Development Program of Guangdong ProvinceChina(No.2020B090924002)。
文摘The Mg-Sn alloys,with basal or prismatic Mg2Sn laths,were employed to reveal the effect of precipitate orientation on twinning behavior quantitatively.The Mg-5wt.%Sn alloys with basal or prismatic Mg2Sn were compressed to study the twinning behaviors.Subsequently,an Orowan strengthening model was developed to quantitatively investigate the critical resolved shear stress(CRSS)increment of precipitates on twinning.The results revealed that the prismatic precipitates hindered the transfer and growth of tensile twins more effectively compared with the basal precipitates.The decreased proportion of tensile twins containing prismatic Mg2Sn might be attributed to a larger CRSS increment for tensile twins compared with that for basal precipitates.The obvious decreased twinning transfer in the alloy with prismatic Mg2Sn could be due to its higher geometrically necessary dislocation and enhanced CRSS of tensile twins.Notably,the prismatic precipitates have a better hindering effect on tensile twins during compression.
基金Project (14JJ6047) supported by the Natural Science Foundation of Hunan Province,ChinaProject (51274092) supported by the National Natural Science Foundation of ChinaProject (20120161110040) supported by the Doctoral Program of Higher Education ofChina
文摘Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.
