“猫眼和铂金浮雕”定制膜工艺在牙膏盒上的应用研究

为提升牙膏产品包装的视觉效果,将定制猫眼膜工艺和定制铂金浮雕膜工艺相结合,应用于牙膏盒印刷品。建立验证其性能指标的测试方案和测试标准。同时解决定制膜与纸之间的剥离强度不稳定、高温出现气泡、粘盒边缘锋利刮手等技术难点。最终验证定制猫眼膜工艺和定制铂金浮雕膜工艺可以在牙膏产品包装上实现批量生产和广泛应用。

供应链环境下MC模式的订单分类

在供应链环境下进行大规模定制(MC)模式的运作,是解决MC模式中规模生产效应同客户个性化需求之间固有矛盾的有效途径。本文在对供应链环境下MC模式基本特征描述与分析的基础上,提出了一种面向供应链环境的MC模式基本运作框架模型。以该模型为基础,详细分析和探讨了与该模式有关的订单分类理论及相关的时间阈值理论。从而,为顺利实现供应链环境下MC模式运作过程的合理优化奠定了必要的技术理论基础。

Oxide film on bubble surface of aluminum foams produced by gas injection foaming process

Based on A356 aluminum alloy,aluminum foams were prepared by gas injection foaming process with pure nitrogen,air and some gas mixtures.The oxygen volume fraction of these gas mixtures varied from 0.2%to 8.0%.Optical microscopy,scanning electron microscopy（SEM） and Auger electron spectroscopy（AES） were used to analyze the influence of oxygen content on cell structure,relative density,macro and micro morphology of cell walls,coverage area fraction of oxide film,thickness of oxide film and other aspects.Results indicate that the coverage area fraction of oxide film on bubble surface increases with the increase of oxygen content when the oxygen volume is less than 1.2%.While when the oxygen volume fraction is larger than 1.6%,an oxide film covers the entire bubble surface and aluminum foams with good cell structure can be produced.The thicknesses of oxide films of aluminum foams produced by gas mixtures containing 1.6%-21%oxygen are almost the same.The reasons why the thickness of oxide film nearly does not change with the variation of oxygen content and the amount of oxygen needed to achieve 100%coverage of oxide film are both discussed.In addition,the role of oxide film on bubble surface in foam stability is also analyzed.

Gas separation using sol–gel derived microporous zirconia membranes with high hydrothermal stability

A microporous zirconia membrane with hydrogen permeance about 5 × 10-8mol·m-2·s-1·Pa-1, H2/CO2 permselectivity of ca. 14, and excellent hydrothermal stability under steam pressure of 100 k Pa was fabricated via polymeric sol–gel process. The effect of calcination temperature on single gas permeance of sol–gel derived zirconia membranes was investigated. Zirconia membranes calcined at 350 °C and 400 °C showed similar single gas permeance, with permselectivities of hydrogen towards other gases, such as oxygen, nitrogen, methane, and sulfur hexa fluoride, around Knudsen values. A much lower CO2permeance（3.7 × 10-9mol·m-2·s-1·Pa-1）was observed due to the interaction between CO2 molecules and pore wall of membrane. Higher calcination temperature, 500 °C, led to the formation of mesoporous structure and, hence, the membrane lost its molecular sieving property towards hydrogen and carbon dioxide. The stability of zirconia membrane in the presence of hot steam was also investigated. Exposed to 100 k Pa steam for 400 h, the membrane performance kept unchanged in comparison with freshly prepared one, with hydrogen and carbon dioxide permeances of 4.7 × 10-8and ~ 3 × 10-9mol·m-2·s-1·Pa-1, respectively. Both H2 and CO2permeances of the zirconia membrane decreased with exposure time to 100 k Pa steam. With a total exposure time of 1250 h, the membrane presented hydrogen permeance of 2.4 × 10-8mol·m-2·s-1·Pa-1and H2/CO2 permselectivity of 28, indicating that the membrane retains its microporous structure.

Characterization and Stability of Na-doped p-type ZnO Thin Films Preparation by Reactive DC Magnetron Sputtering

Na-doped p-type ZnO thin films have been realized by DC reactive magnetron sputtering with a set of metal-Zn targets doped with various Na contents and under different substrate temperatures, respectively. Hall effect measurement, field-emission SEM, X-ray diffraction and optical transmission were carried out to investigate the effects of Na content and substrate temperature on the properties of p-type films. Results indicate that all the Na-doped ZnO films are strongly （002） oriented, and have an average transmittance -85 % in the visible region. Na-doped p-type ZnO films with good structural, electrical, and optical properties can only be obtained at an intermediate amount of Na content and under appropriate substrate temperature. At the optimal condition, the Na-doped p-type ZnO has the lowest resistivity of 13. 8 Ω· cm with the carrier concentration as high as 1.07 × 10^18 em^-3. The stability of the Na-doped p-type ZnO is also studied in this paper and it is found that the electrical properties keep stable in a period of one month.

Controlling reduction degree of graphene oxide membranes for improved water permeance

Tailoring tire pore structure and surface chemistry of graphene-based laminates is essentially important for their applications as separation membranes. Usually, pure graphene oxide （GO） and completely reduced GO （rGO） membranes suffer florn low water permeance because of the lack of pristine graphitic sp2 domains and very small interlayer spacing, respectively. In this work, we studied the influence of reduction degree on the structure and separation pertornrance of rGO membranes, tt was found that weak reduction retains the good dispersion and hydrophilicity of GO nanosheets. More importantly, it increases the number of pristine graphitic sp2 domains in rGO nanosheets while keeping the large interlayer spacing of the GO membranes in most regions at the same time. The resultant mernbranes show a high water permeance of 56.3 L m^-2 h^ -1 bar^ -1, which is about 4 times and over 10^4 times larger tban those of the GO and completely reduced rGO membranes, respectively, and high rejection over 95700 for various dyes. Furthermore, they show better structure stability and more superior separation perfor- mance than GO membranes in acid and alkali environments.