35KV双回路供电定相方法

35KV双回路供电,均装设电压互感器供测量电压、功率及继电器保护信号线路之用。电压互感器一次侧接于高压线路上,二次侧接仪表或继电器。三相供电多采用两台单相电压互感器接成开口三角形,即V型接法,其接线见图1,或者三台单相电压互感器组成yo-yo接法,其接线见图2。

《重要变电所电源的定相方法》的补充

笔者在《电世界》1993年第1期刊登《重要变电所电源的定相方法》一文后,近又有体会,现补充内容如下: 1.原文'3～35kV系统的定相'中第一种方法的第7点:变压器接线组别虽同,但一次相序相反,相量图可能出现图6所示两种形式,出现了这两种图形,用平移的方法是不可能使两个三角形完全重合的,只能更换2号变压器的一次例相序,将ΔL1′L2′L3′翻个个,才能采用上述方法使两个三角形重合,达到同相目的。但盲目地更换一次侧相序。

35kV变电站定相新方法研究探讨

针对电力实际运行生产中存在的定相问题,利用现有的运行设备,提出了定相的新思路和新方法,并通过实验对其技术可行性进行了论证,为简化定相程序做出了有益的尝试。

定相试验方法探讨

随着电网建设的快速发展,对供电可靠性的要求越来越高,双回线网架的增多、变压器更换力度和频次的加大、线路和变压器能否并列运行成为电网建设过程和并网启运前必须解决的课题。鉴别相位,进行定相试验是解决并网运行的重要试验方法。通过对6220 kV电压等级常用定相试验方法的分析,指出了定相试验步骤和注意事项。

二次定相在配电网中的应用

针对一次定相存在送电操作复杂,停电范围扩大,必须解锁五防闭锁装置等问题,提出采用二次定相方法,从二次定相的基本原理、二次定相所应遵循的基本步骤和注意事项、二次定相的特点等方面对该方法进行分析,与一次定相的优缺点进行比较,并通过应用实例证明该方法的安全性和可操作性。

HPLC Determination of Harpagoside and Cinnamic Acid in Radix Scrophulariae

A gradient HPLC method was established for the determination of harpagoside and cinnamic acid in Radix Scrophulariae (Xuanshen) and a proposition was put forward for the lowest content of the characteristic and active constituent (harpagoside) for qualified Radix Scrophulariae. The experimental conditions were as follows: Ultrasphere ODS column (250 mm 4.6 mm, 5 mm), mobile phase: acetonitrile-water (containing 1.0% acetic acid) (20:8050:50) (20 min), flow-rate 1 mLmin-1, room temperature, detection wavelength 278 nm. Twenty-eight samples of Xuan-shen (Radix Scrophulariae) from different districts of China were analyzed and the contents of harpagoside and cinnamic acid in Xuan-shen were 0.041~0.244% and 0.012~0.068% respectively. The recoveries (RSD)% were 97.13(0.80)% for harpagoside and 99.38(0.51)% for cinnamic acid. The method is simple and accurate. It can be used for the quality control of Radix Scrophulariae. We propose that the content of harpagoside in qualified Radix Scrophularia should be no less than 0.05%.

A Method for Detecting Adhesive Related-Factors of Streptococcus suis Serotype 2 by Real-time PCR

[Objective] This study aimed to establish a method for quantitative detection of mRNA transcriptional level of SS2 adhesive related-factors of Streptococcus suis serotype 2 （SS2） by fluorescent quantitative PCR. []Vlethod] The gene fragments en- coding SS2 adhesive related-factors MRP, FBPS and CPS2J and a housekeeping gene aroA were amplified by reverse transcription PCR from the total RNA of SS2, cloned, and sequenced. The recombinant plasmids containing the target genes were constructed, and used as templates in Real-time PCR. [Result] Dynamic curves, stan- dard curves and melting curves of the adhesive related-factors and aroA were ob- tained by the optimized Real-time PCR system. The standard curves showed a good linear relationship between template copy number and circulation number, and the correlation coefficients （FF） of the standard curves were over 0.995. Also, these as- says were highly specific a^d there was single specific melting peak for every gene. Moreover, the assays were highly sensitive and had a detection limit of 1.0×102 copies in 1 μl of initial templates. Finally, it was highly repeatable and had a coeffi- cient of variation less than 2% for intra-assay. [Conclusion] This study will provide a way to reveal the adhesion mechanism of SS2 to different host cells at molecular level.

Determination of brominated diphenyl ethers in atmospheric particulate matter using selective pressurized liquid extraction and gas chromatography–mass spectrometry with a negative chemical ionization

This study describes the development and validation of a sensitive and reliable method for determination of polybrominated diphenyl ethers（PBDEs）in atmospheric particulate matter using selective pressurized liquid extraction（SPLE）and gas chromatography–mass spectrometry with a negative chemical ionization（GC-NCI-MS）.Extraction and clean-up were performed using PLE with 2 g florisil and 3 g silica placed in the extraction cells.Under optimal conditions,14 PBDEs were extracted at 70℃ using hexane/dichloromethane（50：50,v/v）as solvent.Validation of SPLE returned excellent recoveries for most analytes,with relative standard deviations mostly below20%.Method detection limits ranged from 0.13 to15.38 ng·mL^-1 for the GC-MS analyses.The method was successfully applied to atmospheric particulate matter of Beijing,where analytes were detected in the range of182.79 to 468.99 pg·m^-3.

Determination of the gas compositions for direct coal liquefaction by gas chromatography

Via multi-dimensional gas chromatography, configured with parallel dual-channel, double detectors, valves switching and back flushing, rapid analysis of the gas compositions consisting of C1-C5 hydrocarbons and permanent gases, such as CO2, H2S, H2, and CO, for direct coal liquefaction has been realized. With four packed chromatographic columns, which are Hayesep-Q pre-column, Hayesep-Q column, molecular sieve 5A column and one PLOT A1203 S capillary column, the gas compositions for direct coal liquefaction are analyzed qualitatively and quantitatively by the external standard method. The determination method has such advantages as excellent separation, simple operation, rapid analysis and accurate results.

Research on the rheological properties of pesticide suspension concentrate

This study reports research on pesticide suspension rheology and a new rheological parameter, the relative value of approach, which has great advantage for judging the physical stability of a pesticide suspension concentrate. Experiments showed that the system can form stable dispersions when the value of the relative value of approach (Sr) is less than 0.1.

Optimization of Sample Pretreatment for Determination of Polycyclic Aromatic Hydrocarbons in Estuarine Sediments by Gas Chromatography

This study examined levels of polycyclic aromatic hydrocarbons (PAHs) in estuarine sediments in Licun (Qingdao, China) by gas chromatography under optimized conditions for sample pretreatment via ultrasonic extraction, column chromatography, and thin layer chromatography. Methanol and dichloromethane (DCM)/methanol (2:1, v/v) were used in ultrasonic extraction, and DCM was used as eluate for column chromatography. The developing system consisted of n-hexane and DCM at a ratio of 9:1 (v/v), with DCM as the extraction solvent for PAHs-containing silica gel scraped off the plate. When the spiking level is 100 ng, total recoveries of spiked matrices for four target PAHs (phenanthrene, anthracene, pyrene and chrysene) were 83.7%, 76.4%, 85.8%, and 88.7%, respectively, with relative standard deviation (RSD) between 5.0% and 6.5% (n = 4). When the spiking level is 1000 ng, associated total recoveries were 78.6%, 72.7%, 82.7% and 85.3%, respectively, with RSD between 4.4% and 5.3% (n = 4). The opti-mized method was advantageous for determination of PAHs in complex matrix due to its effective sample purification.

Phase Transitions in a Mixture of Hard-Sphere Dipoles and Neutral Hard Spheres

Using the reference hypernetted chain （RHNC） integral equation theory and a rigorous stability analysis method, we investigate the phase behavior of a mixture of hard-sphere dipoles and neutral hard spheres based on the correlations of the homogeneous isotropic phase. Lowering the temperature down to the points where the RHNC equations fail to have a solution, several ttuctuations strongly increase. At low densities our results indicate the onset of ／ chain formation, which is similar with the pure DHS system. At high densities, the results indicate the appearance of isotropic-to-ferroelectric transitions （small neutral hard spheres concentrations） and demixing transitions （large neutral hard spheres concentrations）.

Identification of structural entities in NdF_3-LiF melts with cryoscopic method

Nd-F species in NdF3-LiF melts were studied using cryoscopic method.Liquidus temperatures of melts of various compositions were determined by differential thermal analysis(DTA).Based on the different model calculations,NdF4- was identified as the most likely Nd-F entity in the melts in which the mole fraction of NdF3 was lower than 20%,considering only one single Nd species in the melt,and which was formed in accordance with Temkin model or Flood model.Then,activities of different components in the melts were researched.The results show that activity of LiF decreases,and that of NdF3 increases with increasing the mole fraction of NdF3.The value of activity coefficient of NdF3 is higher than 1,and that of LiF is lower than 1.

Strategic Prospective Methodology to Explore Sustainable Futures

This paper shows prospective methodology as a tool to generate strategic knowledge for designing sustainable futures. The strategic prospective is a social science discipline dedicated to explore the future. Based on qualitative methods with participative experts and stakeholders, the strategic prospective allows designing different future scenarios and planning the transformation of a current situation into a desired future. To design sustainable futures, this paper proposes a four-stage methodology： understanding the context; strategy visualization; design of alternative scenarios and definition of desired future; and planning its construction. This methodology makes evident the possibility of seeking alternative scenarios for a sustainable future in different scopes, particularly, in two prospective applications： biodiversity conservation and water treatment. The outcomes of the application have allowed proposing strategies and policies for the management of environmental goods, such as environmental services and water reuse, with a long-time outlook based on a collective desired future.

Deformation tests and failure process analysis of an anchorage structure

In order to study the failure process of an anchorage structure and the evolution law of the body＇s defor- mation field, anchor push-out tests were carried out based on digital speckle correlation methods （DSCM）. The stress distribution of the anchorage interface was investigated using the particle flow numerical simulation method. The results indicate that there are three stages in the deformation and fail- ure process of an anchorage structure： elastic bonding stage, a de-bonding stage and a failure stage. The stress distribution in the interface controls the stability of the structure. In the elastic bonding stage, the shear stress peak point of the interface is close to the loading end, and the displacement field gradually develops into a ＂V＂ shape, in the de-bonding stage, there is a shear stress plateau in the center of the anchorage section, and shear strain localization begins to form in the deformation field. In the failure stage, the bonding of the interface fails rapidly and the shear stress peak point moves to the anchorage free end. The anchorage structure moves integrally along the macro-cracl~ The de-bonding stage is a research focus in the deformation and failure process of an anchorage structure, and plays an important guiding role in roadway support design and prediction of the stability of the surrounding rock.

Three vertex degree correlations of fixed act-size collaboration networks

A rate equation approach was presented for the exact computation of the three vertex degree correlations of the fixed act-size collaboration networks.Measurements of the three vertex degree correlations were based on a rate equation in the continuous degree and time approximation for the average degree of the nearest neighbors of vertices of degree k,with an appropriate boundary condition.The rate equation proposed can be generalized in more sophisticated growing network models,and also extended to deal with related correlation measurements.Finally,in order to check the theoretical prediction,a numerical example was solved to demonstrate the performance of the degree correlation function.

From Allan Variance to Phase Noise:A New Conversion Approach

A new mathematical method is proposed to convert the oscillator instability parameters from Allan variance to Spectrum Density(SD)of random phase fluctuations,which is the inversion of the classic transformation formula from SD to Allan variance.Due to the fact that Allan variance does not always determine a unique SD function,power-law model of the SD of oscillator phase fluctuations is introduced to the translating algorithm and a constrained maximum likelihood solution is presented.Considering that the inversion is an ill-posed problem,a regularization method is brought forward in the process.Simulation results show that the converted SD of phase fluctuations from Allan variance parameters agrees well with the real SD function.Furthermore,the effects of the selected regularization factors and the input Allan variances are analyzed in detail.

The Constitution and Working Mechanism of the Fast Fashion Enterprise Financial Competitiveness

With the Pearson Correlation Coefficient measurement method, this paper studies the correlation between the various elements influencing the financial competitiveness of the fast fashion enterprieses and the long-term financial stability, which shows that the financial resilience has the biggest correlation with the long-term financial stability, which is followed in sequence by financial management capacity, financial resources capacity, financial performance capacity, and financial activity capacity. This is due to the fact that such factors as financial solvency, financial operations, profitability, growth capacity and the ability to generate cash exert effect upon the long-term stability of the financial competitiveness.

Covariance Estimation Using High-Frequency Data： An Analysis of Nord Pool Electricity Forward Data

The modeling of volatility and correlation is important in order to calculate hedge ratios, value at risk estimates, CAPM （Capital Asset Pricing Model betas）, derivate pricing and risk management in general. Recent access to intra-daily high-frequency data for two of the most liquid contracts at the Nord Pool exchange has made it possible to apply new and promising methods for analyzing volatility and correlation. The concepts of realized volatility and realized correlation are applied, and this study statistically describes the distribution （both distributional properties and temporal dependencies） of electricity forward data from 2005 to 2009. The main findings show that the logarithmic realized volatility is approximately normally distributed, while realized correlation seems not to be. Further, realized volatility and realized correlation have a long-memory feature. There also seems to be a high correlation between realized correlation and volatilities and positive relations between trading volume and realized volatility and between trading volume and realized correlation. These results are to a large extent consistent with earlier studies of stylized facts of other financial and commodity markets.