Based on ＂true triaxial coal rock permeability of coal sample test system , the permeability under different gas pressure to coal specimen in bedding plane and the vertical bedding directions are tested. The results ...Based on ＂true triaxial coal rock permeability of coal sample test system , the permeability under different gas pressure to coal specimen in bedding plane and the vertical bedding directions are tested. The results show that coal structural anisotropy has a greater impact on gas permeability properties, differences in experimental coal permeability are roughly one order of magnitude. In view of the differences of the gas flow characteristics in the coal bedding plane and vertical bedding, established series and parallel choked flow model of coal sample gas seepage, and made a theoretical analysis to the influences of the bedding structure to gas permeability properties.展开更多
The design of structural components in low-cycle fatigue field often requires the knowledge of the cyclic properties of the material, which are commonly described by the classical relation of Ramberg-Osgood. In order ...The design of structural components in low-cycle fatigue field often requires the knowledge of the cyclic properties of the material, which are commonly described by the classical relation of Ramberg-Osgood. In order to obtain the cyclic curve using experimental data from incremental step tests, four methodologies are described and critically discussed. Three methods differ in the procedure of evaluation of the elastic modulus, while in the last one the experimental data are interpolated with a single non-linear regression. The various techniques were applied to data obtained from tests carried out on stainless steel specimens, and the resulting differences were analysed and quantified. An average behaviour was evaluated considering the total set of data obtained from experimental tests. The choice of the most suitable method is related to both the strain range of interest and the goal for which the results are used.展开更多
There has been much heated discussion on College English Test for non-English majors Band 4 and Band 6 because it has exerted great influence on English teaching in Chinese universities. This essay is intended to expl...There has been much heated discussion on College English Test for non-English majors Band 4 and Band 6 because it has exerted great influence on English teaching in Chinese universities. This essay is intended to explore the reliability, validity,practicality and washback of this large-scale test by focusing on CET Band 4. The author of this report discusses the merits as well as some existing problems of this test and offers some suggestions at the end of the essay.展开更多
The inclining experiment is the only regulatory tool to assess ship stability. This experiment is a time consuming process for both real-life tests and ship model experiments. The difficulty is mainly due to a bias in...The inclining experiment is the only regulatory tool to assess ship stability. This experiment is a time consuming process for both real-life tests and ship model experiments. The difficulty is mainly due to a bias in the measurement of heel angle. Nowadays, digital inclinometers are available, but they are expensive. In this study, the use of a smartphone application is presented for ship inclination and rolling-period tests. The idea consists of using accelerometer and gyroscope sensors built into the current smartphones for the measurements. Therefore, some experiments are carried out on an example trawler model to exhibit the uses and advantages of this method. The obtained results are in good agreement with those provided from the pendulum method and natural roll-period test. This application is new, easy, and more accurately assesses metacentric height during the inclining and rolling-period tests.展开更多
In order to utilize the spontaneous accumulation of heat (SAH) reasonably and obtain the high quality sinter with low energy consumption, a lower fuel consumption modeling based on raw materials of a certain steel wor...In order to utilize the spontaneous accumulation of heat (SAH) reasonably and obtain the high quality sinter with low energy consumption, a lower fuel consumption modeling based on raw materials of a certain steel works was built. An air-flow segregation feeding (ASF) experimental equipment was designed to simulate strand feeding process and calculate the lower fuel consumption quantity. Compared with baseline test, the ASF experimental equipment was adopted. The results of sinter pot tests show that the solid fuel consumption is lower than that in baseline test, which is decreased by 5.8%. Meanwhile, other sinter indexes, such as pan yeild, tumbler strength and strand productivity are improved. The mineralogical examination indicates that the mineral compositions and micostructures are improved in sinter.展开更多
Flue gases exhausted from thermal power plants contain more than 50% of the fuel thermal energy. In the present work, experimental investigation was carried out to study the utilization of thermal energy in flue gases...Flue gases exhausted from thermal power plants contain more than 50% of the fuel thermal energy. In the present work, experimental investigation was carried out to study the utilization of thermal energy in flue gases to enhance the performance of modified solar chimney consisting of Savonius wind rotor. A modified solar chimney model was designed and fabricated to carry out experimental measurement. The model consists of thermal energy conversion unit; Savonius wind rotor and a chimney. The thermal energy in the flue gas transfers to the air particles in the air channel across the absorber plate and results in upward air stream due to the buoyancy effect. With an 9 absorber area of 2.36 re＇and flue gas mass flow rate of0.18 kg/s, air velocity＇ of 4.1 m/s was achieved at the top of the thermal unit. Increasing the mass flow rate of the flue gas to 0.24 kg/s enhances the air velocity to be 4.6 m/s. The results have demonstrated the possibility＇ of utilizing the thermal energy in the waste flue gas to enhance the performance of a solar chimney and facilitate the continuous operation during the absence of the sun.展开更多
This paper presents a method of determining the friction coefficient in metal forming using multilayer artificial neural networks based on experimental data obtained from strip drawing test. The number of input variab...This paper presents a method of determining the friction coefficient in metal forming using multilayer artificial neural networks based on experimental data obtained from strip drawing test. The number of input variables of the artificial neural network has been optimized using genetic algorithm. This process is based on surface parameters of the sheet and dies, sheet material parameters and clamping force as input parameters to train the neural network. In addition to demonstrating the fact that regression statistics model using genetic selection and intelligent problem solver are better than models without preprocessing of input data, the sensitivity analysis of the input variables has been conducted. This avoids the time-consuming testing of neurons in finding the best network architecture. The obtained results from this study have also pointed out that genetic algorithm can successfully be applied to optimize the training set and the outputs agree with experimental results. This allows reduction or elimination of expensive experimental tests to determine friction coefficient value.展开更多
This paper aims at investigating the efficacy of different state-of-art damage detection methods when applied to real worm structures subjected to ground motion excitations, for which the literature contributions are,...This paper aims at investigating the efficacy of different state-of-art damage detection methods when applied to real worm structures subjected to ground motion excitations, for which the literature contributions are, at present, still not fully comprehensive. To this purpose the paper analyses two test structures： （1） a four-story scaled steel frame tested on a shake table in a controlled laboratory conditions, and （2） a seven-story reinforced concrete building monitored during the seismic excitations of the 1999 Chi-Chi （Taiwan） Earthquake main shock and numerous fore and afiershocks. Some model based damage approaches and statistics based damage indexes are reviewed. The different methodologies and indexes are, then, applied to the two test structures with the final aim of analysing their performance and validity within the case of a laboratory scaled model and a real world structure subjected to input ground motion.展开更多
Though TES （thermal energy storage） is developed hugely in most of the solar power generation plants, it is less growth in implementing a modular type of TES in a solar plant, e.g., solar dish/stifling engine applic...Though TES （thermal energy storage） is developed hugely in most of the solar power generation plants, it is less growth in implementing a modular type of TES in a solar plant, e.g., solar dish/stifling engine application. The main issue in designing the TES system is its thermal capacity of storage materials, e.g., insulator. This study is focusing on the potential waste material as an insulator for thermal energy storage applications. The insulator usage is to reduce the heat transfer between two mediums and the capability is measured by its resistance to heat flow. It is needed to obtain optimal materials to energy conversion at the same time reduce the waste generation. Therefore, a small-scale experimental testing of natural cooling process of an insulated tank within a confined room without any forced cooling system, e.g., fan. The testing is repeated by changing the insulator using the potential waste material from natural and industrial waste and also by changing the HTF （heat transfer fluid）. The analysis is performed on the relationship between heat loss and the reserved period by the insulator. The results indicate the percentage of period of the insulated tank withstands the heat compared to non-insulated tank, e.g., cotton reserved the period of 14% more than non-insulated tank to withstand the heat transfer of cooking oil to the surrounding. The paper finally justifies the most potential waste material as an insulator in different heat transfer fluids.展开更多
Through the comparison of various acquisition technology and related technology theory of the existing scheme, the paper analyze and design the power battery testing platform of the data acquisition system, and give t...Through the comparison of various acquisition technology and related technology theory of the existing scheme, the paper analyze and design the power battery testing platform of the data acquisition system, and give the research design scheme of the utility model through the design of the software on PC and CAN bus, which makes the full synchronization requirements acquisition unit; improve the linearity and stability of total voltage and current acquisition by the integrated circuit, and improve the system sampling rate, effectively complete the corresponding index. Finally, through experimental verification, to ensure the completion of the technical indicators.展开更多
文摘Based on ＂true triaxial coal rock permeability of coal sample test system , the permeability under different gas pressure to coal specimen in bedding plane and the vertical bedding directions are tested. The results show that coal structural anisotropy has a greater impact on gas permeability properties, differences in experimental coal permeability are roughly one order of magnitude. In view of the differences of the gas flow characteristics in the coal bedding plane and vertical bedding, established series and parallel choked flow model of coal sample gas seepage, and made a theoretical analysis to the influences of the bedding structure to gas permeability properties.
文摘The design of structural components in low-cycle fatigue field often requires the knowledge of the cyclic properties of the material, which are commonly described by the classical relation of Ramberg-Osgood. In order to obtain the cyclic curve using experimental data from incremental step tests, four methodologies are described and critically discussed. Three methods differ in the procedure of evaluation of the elastic modulus, while in the last one the experimental data are interpolated with a single non-linear regression. The various techniques were applied to data obtained from tests carried out on stainless steel specimens, and the resulting differences were analysed and quantified. An average behaviour was evaluated considering the total set of data obtained from experimental tests. The choice of the most suitable method is related to both the strain range of interest and the goal for which the results are used.
文摘There has been much heated discussion on College English Test for non-English majors Band 4 and Band 6 because it has exerted great influence on English teaching in Chinese universities. This essay is intended to explore the reliability, validity,practicality and washback of this large-scale test by focusing on CET Band 4. The author of this report discusses the merits as well as some existing problems of this test and offers some suggestions at the end of the essay.
文摘The inclining experiment is the only regulatory tool to assess ship stability. This experiment is a time consuming process for both real-life tests and ship model experiments. The difficulty is mainly due to a bias in the measurement of heel angle. Nowadays, digital inclinometers are available, but they are expensive. In this study, the use of a smartphone application is presented for ship inclination and rolling-period tests. The idea consists of using accelerometer and gyroscope sensors built into the current smartphones for the measurements. Therefore, some experiments are carried out on an example trawler model to exhibit the uses and advantages of this method. The obtained results are in good agreement with those provided from the pendulum method and natural roll-period test. This application is new, easy, and more accurately assesses metacentric height during the inclining and rolling-period tests.
基金Project(NECT-04-0748) supported by New Century Excellent Talents Program of China
文摘In order to utilize the spontaneous accumulation of heat (SAH) reasonably and obtain the high quality sinter with low energy consumption, a lower fuel consumption modeling based on raw materials of a certain steel works was built. An air-flow segregation feeding (ASF) experimental equipment was designed to simulate strand feeding process and calculate the lower fuel consumption quantity. Compared with baseline test, the ASF experimental equipment was adopted. The results of sinter pot tests show that the solid fuel consumption is lower than that in baseline test, which is decreased by 5.8%. Meanwhile, other sinter indexes, such as pan yeild, tumbler strength and strand productivity are improved. The mineralogical examination indicates that the mineral compositions and micostructures are improved in sinter.
文摘Flue gases exhausted from thermal power plants contain more than 50% of the fuel thermal energy. In the present work, experimental investigation was carried out to study the utilization of thermal energy in flue gases to enhance the performance of modified solar chimney consisting of Savonius wind rotor. A modified solar chimney model was designed and fabricated to carry out experimental measurement. The model consists of thermal energy conversion unit; Savonius wind rotor and a chimney. The thermal energy in the flue gas transfers to the air particles in the air channel across the absorber plate and results in upward air stream due to the buoyancy effect. With an 9 absorber area of 2.36 re＇and flue gas mass flow rate of0.18 kg/s, air velocity＇ of 4.1 m/s was achieved at the top of the thermal unit. Increasing the mass flow rate of the flue gas to 0.24 kg/s enhances the air velocity to be 4.6 m/s. The results have demonstrated the possibility＇ of utilizing the thermal energy in the waste flue gas to enhance the performance of a solar chimney and facilitate the continuous operation during the absence of the sun.
文摘This paper presents a method of determining the friction coefficient in metal forming using multilayer artificial neural networks based on experimental data obtained from strip drawing test. The number of input variables of the artificial neural network has been optimized using genetic algorithm. This process is based on surface parameters of the sheet and dies, sheet material parameters and clamping force as input parameters to train the neural network. In addition to demonstrating the fact that regression statistics model using genetic selection and intelligent problem solver are better than models without preprocessing of input data, the sensitivity analysis of the input variables has been conducted. This avoids the time-consuming testing of neurons in finding the best network architecture. The obtained results from this study have also pointed out that genetic algorithm can successfully be applied to optimize the training set and the outputs agree with experimental results. This allows reduction or elimination of expensive experimental tests to determine friction coefficient value.
文摘This paper aims at investigating the efficacy of different state-of-art damage detection methods when applied to real worm structures subjected to ground motion excitations, for which the literature contributions are, at present, still not fully comprehensive. To this purpose the paper analyses two test structures： （1） a four-story scaled steel frame tested on a shake table in a controlled laboratory conditions, and （2） a seven-story reinforced concrete building monitored during the seismic excitations of the 1999 Chi-Chi （Taiwan） Earthquake main shock and numerous fore and afiershocks. Some model based damage approaches and statistics based damage indexes are reviewed. The different methodologies and indexes are, then, applied to the two test structures with the final aim of analysing their performance and validity within the case of a laboratory scaled model and a real world structure subjected to input ground motion.
文摘Though TES （thermal energy storage） is developed hugely in most of the solar power generation plants, it is less growth in implementing a modular type of TES in a solar plant, e.g., solar dish/stifling engine application. The main issue in designing the TES system is its thermal capacity of storage materials, e.g., insulator. This study is focusing on the potential waste material as an insulator for thermal energy storage applications. The insulator usage is to reduce the heat transfer between two mediums and the capability is measured by its resistance to heat flow. It is needed to obtain optimal materials to energy conversion at the same time reduce the waste generation. Therefore, a small-scale experimental testing of natural cooling process of an insulated tank within a confined room without any forced cooling system, e.g., fan. The testing is repeated by changing the insulator using the potential waste material from natural and industrial waste and also by changing the HTF （heat transfer fluid）. The analysis is performed on the relationship between heat loss and the reserved period by the insulator. The results indicate the percentage of period of the insulated tank withstands the heat compared to non-insulated tank, e.g., cotton reserved the period of 14% more than non-insulated tank to withstand the heat transfer of cooking oil to the surrounding. The paper finally justifies the most potential waste material as an insulator in different heat transfer fluids.
文摘Through the comparison of various acquisition technology and related technology theory of the existing scheme, the paper analyze and design the power battery testing platform of the data acquisition system, and give the research design scheme of the utility model through the design of the software on PC and CAN bus, which makes the full synchronization requirements acquisition unit; improve the linearity and stability of total voltage and current acquisition by the integrated circuit, and improve the system sampling rate, effectively complete the corresponding index. Finally, through experimental verification, to ensure the completion of the technical indicators.
