新型超高强度高导流性压裂支撑剂

目前，油田现场应用的支撑剂主要有天然砂、树脂涂敷砂和陶粒3类。但是，随着深层储层的开发及热力采油、蒸汽驱等的应用，传统的支撑剂在137.9 M Pa以上闭合压力下无法提供足够的导流性。为此，美国某公司研发了一种超高强度高导流性支撑剂，可应用于高压力地区以及其他类似于热力、蒸汽驱等的环境中。

腿部手术罩布用水刺非织造基材的性能研究

选用30%聚酯纤维和70%粘胶纤维的混合纤维为原料,在清洁化水刺加工环境条件下,运用复合铺网工艺和特殊的圆形颗粒状鼓套研制腿部手术罩布用非织造基材。与使用复合铺网工艺和普通珍珠纹状鼓套生产的水刺非织造基材作性能对比,结果表明圆形颗粒状非织造基材吸液能力提高,且具有良好的液体纵向导流性;对圆形颗粒状非织造基材正反面的液体扩散性进行测试,结果表明该材料正面与皮肤接触更能满足腿部手术罩布基本性能的要求。

一步成型玻璃纤维连续毡在复合材料中的应用

一步成型玻璃纤维连续毡是一种高性能玻纤无纺增强基材,相对于二步成型连续毡及其他增强材料具有各向同性,导流性能优良,制品层间粘结强度高、不易分层,表面平整、加工性能好等优点,在汽车、电子、建筑、航空等领域应用日趋普遍,市场需求迫切,前景十分广阔。

塔河油田碳酸盐岩油藏试井曲线分类及其生产特征分析

经对塔河油田碳酸盐岩油藏试井曲线分类 ,可以认识油藏的渗流介质类型 ,认识储集层发育的非均质性 ,同时把试井曲线类型与其生产特征相结合 。

Effect of Zr and Sc on mechanical properties and electrical conductivities of Al wires

In order to obtain the Al wires with good mechanical properties and high electrical conductivities, conductive wires of Al-0.16 Zr, Al-0.16 Sc, Al-0.12Sc-0.04Zr（mass fraction, %） and pure Al（99.996%） were produced with the diameter of 9.5 mm by continuous rheo-extrusion technology, and the extruded materials were heat treated and analyzed. The results show that the separate additions of 0.16% Sc and 0.16% Zr to pure Al improve the ultimate tensile strength but reduce the electrical conductivity, and the similar trend is found in the Al-0.12Sc-0.04 Zr alloy. After the subsequent heat treatment, the wire with the optimum comprehensive properties is Al-0.12Sc-0.04 Zr alloy, of which the ultimate tensile strength and electrical conductivity reach 160 MPa and 64.03%（IACS）, respectively.

Electrical and mechanical properties of Cu-Cr-Zr alloy aged under imposed direct continuous current

The Cu-Cr-Zr alloys were aged at different temperatures for different time with different current densities. The results show that both the electrical conductivity and hardness are greatly improved after being aged with current at a proper temperature. The electrical conductivity increases approximately linearly with increasing current density while the hardness remains constant. The microstructure observation reveals that a much higher density of dislocations and nanosized Cr precipitates appear after the imposition of current, which contributes to the higher electrical conductivity and hardness. The mechanism is related with three factors： 1） Joule heating due to the current, 2） migration of mass electrons, 3） solute atoms, vacancies, and dislocations promoted by electron wind force.

Inhibition of Telomerase with hTERT Antisense Increases Susceptibility of Leukemic Cells to CDDP-induced Apoptosis

Objective: To investigated the e?ect of inhibition of telomerase with hTERT antisense on leukemic cells (HL-60 and K562) to CDDP-induced apoptosis. Methods: Antisense phosphorothioate oligodeoxynucleotide (AS PS-ODN) was synthesized and puri?ed. Telomerase activity was detected by Telomerase PCR ELASA kit and cell apoptosis was observed by morphological method and determined by ?owcytometry. Results: AS PS-ODN could signi?cantly inhibit telomerase activity by down regulat- ing the hTERT expression, and increase the susceptibility of leukemic cells to CDDP-induced apoptosis. Conclusion: Inhibition of telomerase with hTERT antisense can increases the susceptibility of leukemic cells to CDDP-induced apoptosis.

A Linear CMOS OTA and Its Application to a 3.3V 20 MHz High-Q g_m-C Bandpass Filter

A design of a linear and fully-balanced operational transconductanee amplifier （OTA） with improved high DC gain and wide bandwidth is presented. Derivative from a single common-source field effect transistor （FET） cas- cade and its DC I-V characteristics,the third-order coefficient g3 hasbeen well compensated with a parallel FET operated in the triode region, which has even-odd symmetries between the boundary of the saturation and triode region. Therefore,for high linearity,a simple solution is obtained to increase input signal amplitude in saturation for the application of OTA continuous-time filters. A negative resistance load （NRL） technique is used for the compensation of parasitic output resistance and an achievement of a high DC-gain of the OTA circuits without extra internal nodes. Additionally, derivations from the ideal -90° phase of the gm-C integrator mainly due to a finite DC gain and parasitic poles will be avoided in the frequency range of interest. HSPICE simulation shows that the total harmonic distortion at 1Vp-p is less than 1% from a single 3.3V supply. As an application of the VHF CMOS OTA,a second-order OTA-C bandpass filter is fabricated using a 0. 18μm CMOS process with two kinds of gate-oxide layers, which has achieved a center frequency of 20MHz,a 3dB-bandwidth of 180kHz,and a quality factor of 110.

Ionic Conduction and Fuel Cell Performance of Ba0.98Ce0.8Tm0.2O3-α Ceramic

The perovskite-type oxide solid solution Ba0.98Ce0.8Tm0.2O3-α was prepared by high temperature solid-state reaction and its single phase character was confirmed by X-ray diffraction. The conduction property of the sample was investigated by alternating current impedance spectroscopy and gas concentration cell methods under different gases atmospheres in the temperature range of 500-900 ℃. The performance of the hydrogen-air fuel cell using the sample as solid electrolyte was measured. In wet hydrogen, the sample is a pure protonic conductor with the protonic transport number of 1 in the range of 500-600 ℃, a mixed conductor of proton and electron with the protonic transport number of 0.945-0.933 above 600 ℃. In wet air, the sample is a mixed conductor of proton, oxide ion, and electronic hole. The protonic transport numbers are 0.010-0.021, and the oxide ionic transport numbers are 0.471-0.382. In hydrogen-air fuel cell, the sample is a mixed conductor of proton, oxide ion and electron, the ionic transport numbers are 0.942 0.885. The fuel cell using Ba0.98Ce0.8Tm0.2O3-α as solid electrolyte can work stably. At 900 ℃, the maximum power output density is 110,2 mW/cm2, which is higher than that of our previous cell using Ba0.98Ce0.8Tm0.2O3-α （x〈≤1, RE=Y, Eu, Ho） as solid electrolyte.

Electrical conductivity effect on MHD mixed convection of nanofluid flow over a backward-facing step

In this study,magneto-hydrodynamics (MHD) mixed convection effects of Al2O3-water nanofluid flow over a backward-facing step were investigated numerically for various electrical conductivity models of nanofluids.A uniform external magnetic field was applied to the flow and strength of magnetic field was varied with different values of dimensionless parameter Hartmann number (Ha=0,10,20,30,40).Three different electrical conductivity models were used to see the effects of MHD nanofluid flow.Besides,five different inclination angles between 0°-90° is used for the external magnetic field.The problem geometry is a backward-facing step which is used in many engineering applications where flow separation and reattachment phenomenon occurs.Mixed type convective heat transfer of backward-facing step was examined with various values of Richardson number (Ri=0.01,0.1,1,10) and four different nanoparticle volume fractions (Ф=0.01,0.015,0.020,0.025) considering different electrical conductivity models.Finite element method via commercial code COMSOL was used for computations.Results indicate that the addition of nanoparticles enhanced heat transfer significantly.Also increasing magnetic field strength and inclination angle increased heat transfer rate.Effects of different electrical conductivity models were also investigated and it was observed that they have significant effects on the fluid flow and heat transfer characteristics in the presence of magnetic field.

Use of 3-D magnetic resonance electrical impedance tomography in detecting human cerebral stroke: a simulation study

We have developed a new three dimensional (3-D) conductivity imaging approach and have used it to detect human brain conductivity changes corresponding to acute cerebral stroke. The proposed Magnetic Resonance Electrical Impedance Tomography (MREIT) approach is based on the J-Substitution algorithm and is expanded to imaging 3-D subject conductivity distribution changes. Computer simulation studies have been conducted to evaluate the present MREIT imaging approach. Simulations of both types of cerebral stroke, hemorrhagic stroke and ischemic stroke, were performed on a four-sphere head model. Simulation results showed that the correlation coefficient (CC) and relative error (RE) between target and estimated conductivity distributions were 0.9245±0.0068 and 8.9997%±0.0084%, for hemorrhagic stroke, and 0.6748±0.0197 and 8.8986%±0.0089%, for ischemic stroke, when the SNR (signal-to-noise radio) of added GWN (Gaussian White Noise) was 40. The convergence characteristic was also evaluated according to the changes of CC and RE with different iteration numbers. The CC increases and RE decreases monotonously with the increasing number of iterations. The present simulation results show the feasibility of the proposed 3-D MREIT approach in hemorrhagic and ischemic stroke detection and suggest that the method may become a useful alternative in clinical diagnosis of acute cerebral stroke in humans.

EUS-guided drainage is more successful in pancreatic pseudocysts compared with abscesses

AIM: To compare the results for endoscopic ultrasound (EUS)-guided drainage of clear fluid pancreatic pseudocysts with the results for abscess drainage. METHODS: All patients referred for endoscopic drainage of a fluid collection were prospectively included. The outcome was recorded. RESULTS: Altogether 26 pseudocysts or abscesses were treated in 25 (6 female) patients. One endoscopist performed the procedures. Non-infected pseudocysts were present in 15 patients and 10 patients had infected fluid collections. The cyst size ranged between 28 cm × 13 cm and 5 cm × 5 cm. The EUS drainage was successful in 94% of the pseudocysts and in 80% of the abscesses (P = 0.04). The complication rate in pseudocysts was 6% and in abscesses was 30% (P = 0.02). Recurrence of a pseudocyst occurred in one patient (4%) after 6 mo; the patient was successfully retreated. CONCLUSION: EUS-guided drainage of pseudocysts is associated with a higher success rate and a lower complication rate compared with abscess drainage.

Typical application of Rogowski coils in inspection of electrobath

During the aluminum electrolytic roasting process,each component of the electrobath of aluminum performs unsteadily when the electrolytic bath is in the pre-roasting stage. It is important to monitor the currents of the anodes and the cathodes of the aluminum electrobath at regular intervals. Both practice and investigation indicate that Rogowski coil can be adopted to measure heavy direct current of the anodes and the cathodes of the aluminum electrobath. The paper not only introduces the typical application of the Rogowski coil to inspect the state of aluminum electrobath in the roasting process, but also analyzes the principles of the coil sensor including its dynamic properties and some important measurement results respectively. The optimal parameters of the coil can be simulated by means of an advanced simulation tool: simulink tools based on MATLAB soft environment. Based on the gathered current data, an even-current coefficient has been introduced, and the current curve can be drawn. Since they are applied in AL-Electrolyzing, it is possible to distinguish the anode of which the current is not evenly distributed, and to take adjusting measures over a period of time to ensure that the current is evenly distributed.

Current Limiting Characteristic Analysis of Magnetic-controlled Switcher Type Fault Current Limiter

A novel magnetic-controlled switcher type fault current limiter (FCL) based on the topology of the saturated iron core high temperature superconducting FCL is proposed. The magnetic field distribution of the FCL iron core is analyzed by FEA software ANSYS. The current limiting characteristic is investigated by both 3-D field-circuit coupled simulation and Matlab. The experiments on the 220 V/50 A test model show that the FCL can limit the fault current swiftly and effectively,and the FCL has the advantages of simple and reliable structure, flexible control strategy. The simulation and experimental results prove that the theoretical expectation and current limiting performance is satisfactory for practical use.

Performance enhancement of filled-type solar collector with U-tube

In order to increase the efficiency of solar collector, a methodology is proposed based on the analysis of its influencing factors, such as thermal conductivity of filled layer, structure forms of filled layer and heat loss coefficient. The results of analysis show that the heat transfer between pipes in evacuated tube is one of the most important factors, which can lead to the decrease of the outlet temperature of working fluid. In order to eliminate the negative influence of the heat transfer between pipes, the hollow filled-type evacuated tube with U-tube(HUFET) was developed, and the heat transfer characteristics of HUFET were analyzed by theoretical and experimental studies. The results show that the thermal resistances decrease with the increase of the thermal conductivity of filled layer. When the thermal conductivity is over 10 W/(m·K), the change of thermal resistances is very little.Furthermore, the larger the thermal conductivity of filled layer, the less the rate of the energy transfer between the two pipes to the total energy transfer, which is between the absorber tube and the working fluid. There is a little difference between the efficiencies of HUFET and UFET, with the efficiency of HUFET 2.4% higher than that of UFET. Meanwhile, the validation of the model developed was confirmed by the experiment.

Anomalous Transport Characteristics of High Temperature Superconductors and Josephson Currents

The transport characteristics of high temperature superconductor current and Josephson current is inves-tigated in the framework of the modified time-dependent Ginzburg-Landau model and the Lawrence-Doniach model.We evaluated the vortex equation and found that the signs of the high temperature superconductor current and theJosephson current can reverse. Some explicit expressions for different cases are derived, which accord with experimentaldata.

Pancreatic pseudocyst

Pancreatic pseudocysts are complications of acute or chronic pancreatitis. Initial diagnosis is accomplished most often by cross-sectional imaging. Endoscopic ultrasound with fine needle aspiration has become the preferred test to help distinguish pseudocyst from other cystic lesions of the pancreas. Most pseudocysts resolve spontaneously with supportive care. The size of the pseudocyst and the length of time the cyst has been present are poor predictors for the potential of pseudocyst resolution or complications, but in general, larger cysts are more likely to be symptomatic or cause complications. The main two indications for some type of invasive drainage procedure are persistent patient symptoms or the presence of complications (infection, gastric outlet or biliary obstruction, bleeding). Three different strategies for pancreatic pseudocysts drainage are available: endoscopic (transpapillary or transmural) drainage, percutaneous catheter drainage, or open surgery. To date, no prospective controlled studies have compared directly these approaches. As a result, the management varies based on local expertise, but in general, endoscopic drainage is becoming the preferred approach because it is less invasive than surgery, avoids the need for external drain, and has a high long-term success rate. A tailored therapeutic approach taking into consideration patient preferences and involving multidisciplinary team of therapeutic endoscopist, interventional radiologist and pancreatic surgeon should be considered in all cases.

Rate decline analysis of multiple fractured horizontal well in shale reservoir with triple continuum

Multiple fractured horizontal well(MFHW) is widely applied in the development of shale gas. To investigate the gas flow characteristics in shale, based on a new dual mechanism triple continuum model, an analytical solution for MFHW surrounded by stimulated reservoir volume(SRV) was presented. Pressure and pressure derivative curves were used to identify the characteristics of flow regimes in shale. Blasingame type curves were established to evaluate the effects of sensitive parameters on rate decline curves, which indicates that the whole flow regimes could be divided into transient flow, feeding flow, and pseudo steady state flow. In feeding flow regime, the production of gas well is gradually fed by adsorbed gases in sub matrix, and free gases in matrix. The proportion of different gas sources to well production is determined by such parameters as storability ratios of triple continuum, transmissibility coefficients controlled by dual flow mechanism and fracture conductivity.

MHD three dimensional flow of viscoelastic fluid with thermal radiation and variable thermal conductivity

The objective of the present work is to model the magnetohydrodynamic(MHD) three dimensional flow of viscoelastic fluid passing a stretching surface. Heat transfer analysis is carried out in the presence of variable thermal conductivity and thermal radiation. Arising nonlinear analysis for velocity and temperature is computed. Discussion to importantly involved parameters through plots is presented. Comparison between present and previous limiting solutions is shown. Numerical values of local Nusselt number are computed and analyzed. It can be observed that the effects of viscoelastic parameter and Hartman number on the temperature profile are similar in a qualitative way. The variations in temperature are more pronounced for viscoelastic parameter K in comparison to the Hartman number M. The parameters N and ε give rise to the temperature. It is interesting to note that values of local Nusselt number are smaller for the larger values of ε.

Study Under AC Stimulation on Excitement Properties of Weighted Small-World Biological Neural Networks with Side-Restrain Mechanism

In this paper, we propose a new model of weighted small-world biological neural networks based on biophysical Hodgkin-Huxley neurons with side-restrain mechanism. Then we study excitement properties of the model under alternating current （AC） stimulation. The study shows that the excitement properties in the networks are preferably consistent with the behavior properties of a brain nervous system under different AC stimuli, such as refractory period and the brain neural excitement response induced by different intensities of noise and coupling. The results of the study have reference worthiness for the brain nerve electrophysiology and epistemological science.