The failure depth of the coal seam floor is one important consideration that must be kept in mind when mining is carried out above a confined aquifer.Determining the floor failure depth is the essential precondition f...The failure depth of the coal seam floor is one important consideration that must be kept in mind when mining is carried out above a confined aquifer.Determining the floor failure depth is the essential precondition for predicting the water-resisting ability of the floor.We have used a high-precision microseismic monitoring technique to overcome the limited amount of data available from field measurements. The failure depth of a coal seam floor,especially an inclined coal seam floor,may be more accurately estimated by monitoring the continuous,dynamic failure of the floor.The monitoring results indicate the failure depth of the coal seam floor near the workface conveyance roadway（the lower crossheading） is deeper and that the failure range is wider here compared to the coal seam floor near the return airway（the upper crossheading）.The results of micro-seismic monitoring show that the dangerous area for water-inrush from the coal seam floor may be identified.This provides an important field measurement that helps ensure safe and highly efficient mining of the inclined coal seam above the confined aquifer at the Taoyuan Coal Mine.展开更多
Mechanical properties of galvannealed (GA) steel sheet used for automotive exposed panel and predicted failure phenomenon of its coating layer were evaluated using finite element method. V-bending test was performed t...Mechanical properties of galvannealed (GA) steel sheet used for automotive exposed panel and predicted failure phenomenon of its coating layer were evaluated using finite element method. V-bending test was performed to understand better the fracture of coating layer of GA steel sheet during plastic deformation. Yield strength of the coating layer was calculated by using a relative difference between hardness of coating layer measured from the nano-indentation test and that of substrate. To measure shearing strength at the interface between substrate and coating layer, shearing test with two specimens attached by an adhesive was carried out. Using the mechanical properties measured, a series of finite element analyses coupled with a failure model was performed. Results reveal that the fracture of coating layer occurs in an irregular manner at the region where compressive deformation is dominant. Meanwhile, a series of vertical cracks perpendicular to material surface are observed at the tensile stressed-region. It is found that 0.26-0.28 of local equivalent plastic strain exists at the coating and substrate at the beginning of failure. The fracture of coating layer depends on ductility of the coating layer considerably as well.展开更多
To pre-compress the disk-shaped LY12 samples along the radial direction can be done with the aid of overstress assembly by heating or by mechanical clamping, which can also generate the deviatoric stress fields under ...To pre-compress the disk-shaped LY12 samples along the radial direction can be done with the aid of overstress assembly by heating or by mechanical clamping, which can also generate the deviatoric stress fields under different states. The spallation signals of these pre-compressed samples are measured by VISAR in the light-gas gun shock experiments. The experimental results show that even under the same impact velocity, the pullback amplitudes of the velocity at the free surface of the sam- pies vary significantly. According to the experimental data, we propose a distinct concept that the material spallation strength is closely related to the deviatoric stress fields in the material. Based on the numerical simulation, we develop a damage con- stitutive model, which reveals that the deviatoric stress reduces the tensile threshold of the void growth. The numerical inves- tigations also demonstrate that the spallation strength decreases as pre-compression increases. The experimental idea proposed in this paper can also be used to study the spallation process in other structures.展开更多
基金supported by the National Basic Research Program ofChina(No.2010CB202210)the National Natural Science Foundation of China(No.50874103)+1 种基金the Natural Science Foundation of Jiangsu Province(No.KB2008135)as well as by the Qinglan Project of Jiangsu Province
文摘The failure depth of the coal seam floor is one important consideration that must be kept in mind when mining is carried out above a confined aquifer.Determining the floor failure depth is the essential precondition for predicting the water-resisting ability of the floor.We have used a high-precision microseismic monitoring technique to overcome the limited amount of data available from field measurements. The failure depth of a coal seam floor,especially an inclined coal seam floor,may be more accurately estimated by monitoring the continuous,dynamic failure of the floor.The monitoring results indicate the failure depth of the coal seam floor near the workface conveyance roadway（the lower crossheading） is deeper and that the failure range is wider here compared to the coal seam floor near the return airway（the upper crossheading）.The results of micro-seismic monitoring show that the dangerous area for water-inrush from the coal seam floor may be identified.This provides an important field measurement that helps ensure safe and highly efficient mining of the inclined coal seam above the confined aquifer at the Taoyuan Coal Mine.
基金supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (2009-0074936)
文摘Mechanical properties of galvannealed (GA) steel sheet used for automotive exposed panel and predicted failure phenomenon of its coating layer were evaluated using finite element method. V-bending test was performed to understand better the fracture of coating layer of GA steel sheet during plastic deformation. Yield strength of the coating layer was calculated by using a relative difference between hardness of coating layer measured from the nano-indentation test and that of substrate. To measure shearing strength at the interface between substrate and coating layer, shearing test with two specimens attached by an adhesive was carried out. Using the mechanical properties measured, a series of finite element analyses coupled with a failure model was performed. Results reveal that the fracture of coating layer occurs in an irregular manner at the region where compressive deformation is dominant. Meanwhile, a series of vertical cracks perpendicular to material surface are observed at the tensile stressed-region. It is found that 0.26-0.28 of local equivalent plastic strain exists at the coating and substrate at the beginning of failure. The fracture of coating layer depends on ductility of the coating layer considerably as well.
基金supported by the National Natural Science Foundation of China (Grant No. 10772165)the CAEP Foundation for Basic Research (Grant No. 2005R0802)
文摘To pre-compress the disk-shaped LY12 samples along the radial direction can be done with the aid of overstress assembly by heating or by mechanical clamping, which can also generate the deviatoric stress fields under different states. The spallation signals of these pre-compressed samples are measured by VISAR in the light-gas gun shock experiments. The experimental results show that even under the same impact velocity, the pullback amplitudes of the velocity at the free surface of the sam- pies vary significantly. According to the experimental data, we propose a distinct concept that the material spallation strength is closely related to the deviatoric stress fields in the material. Based on the numerical simulation, we develop a damage con- stitutive model, which reveals that the deviatoric stress reduces the tensile threshold of the void growth. The numerical inves- tigations also demonstrate that the spallation strength decreases as pre-compression increases. The experimental idea proposed in this paper can also be used to study the spallation process in other structures.
