X射线相位衬度层析成像的数学模型

X射线成像技术在医疗诊断和无损检测等领域有着广泛的应用。对于软组织等弱吸收物体,传统的吸收成像无法获得高对比度的图像。为了解决这个问题,产生了X射线相位衬度成像技术。本文介绍类同轴全息测量下的X射线相位衬度层析成像技术,重点讨论该成像技术的Bronnikov模型和基于Helmholtz方程的模型,及相应的重建方法。

钻孔雷达层析成像技术的研究与应用

我们经常所说的探地雷达包括地面探地雷达和钻孔探地雷达.我国在地面探地雷达技术的使用和研究方面已经取得了很大的成绩,但对于钻孔雷达的使用和研究尚处于初步阶段.本文在阅读大量文献的基础上,概述了目前钻孔雷达的发展状况,对钻孔雷达层析成像技术方法原理作了详细分析,并给出了其数理实现过程.通过应用实例分析其实际应用效果,根据解释结果给出了相应的工程地质评价和施工建议.最后指出其存在的缺点和未来的发展前景.希望本文对我国钻孔雷达层析成像技术进一步的发展、研究和应用有所启示.

粗颗粒矿物在矿浆相中的悬浮特征

浮选过程中颗粒的悬浮是气泡与颗粒碰撞和黏附的基础条件。粗颗粒矿物由于尺寸较大,在矿浆相中的悬浮特征有别于常规粒级和细粒级矿物。为了分析粗颗粒在浮选机矿浆相中的悬浮影响因素,以层析度函数为分析手段,选取金矿、钛铁矿、黄铜矿三种浮选系统中的四种规格浮选机中的粗颗粒为研究对象,研究了三种矿物在单槽浮选机内、沿作业分布、随浮选机规格变化等情况下的悬浮特征。结果表明:在单体浮选机竖直截面内,粗颗粒矿物在叶轮上方悬浮效果比其它粒级差,随着高度的增加重量层析度迅速减小;沿作业分布的三台同规格浮选机内的粗颗粒矿物悬浮特征相近;而浮选机的规格大小对粗颗粒的悬浮特征影响不敏感,给矿粒级分布和矿物的比重对粗颗粒的悬浮特征影响强烈。在同一浮选机槽体,固相颗粒重量分布层析度与金属量分布层析度两者变化并不一致,粗颗粒分选环境尤其明显,这为粗颗粒浮选机的设计提供了新的思路。

Travel time tomography by ray tracing using the fast sweeping method

This paper presents a gradient-descent travel time tomography method for solving the acoustictype velocity model inversion problem.Similarly to the adjoint-state method,the proposed method is based on the Eikonal equation,enabling simultaneous calculation of contributions from all common-source receivers to the gradient.This overcomes the ineffi ciency inherent in conventional travel time tomography methods,which rely on a two-point ray tracing process.By directly calculating Fréchet derivatives,our method avoids the complex derivation processes associated with the adjoint-state method.The key to calculating the Fréchet derivatives is to calculate a so-called ray-path term.Consequently,compared to the adjoint-state method,the proposed method can explicitly obtain the ray paths,resulting in a more concise and intuitive derivation process.Furthermore,our method retains the benefi ts of the adjoint-state method,such as speed,low memory usage,and robustness.This paper focuses on elucidating the principles and algorithms for calculating the raypath term based on the fast sweeping method.The algorithms could be further speeded up by using parallel computational techniques.Synthetic tests demonstrate that our proposed travel time tomographic method accurately calculates ray paths,regardless of the complexity of the model and recording geometry.

Experimental investigation of vibration pretreatment-microwave curing process for carbon fiber reinforced resin matrix composites

The vibration pretreatment-microwave curing process is an efficient,low energy consumption,and high-quality out-of-autoclave curing process for carbon fiber resin matrix composites.This study aims to investigate the impact of vibration pretreatment temperature on the fiber weight content,microscopic morphology and mechanical properties of the composite laminates by using optical digital microscopy,universal tensile testing machine and thermo-gravimetric analyzer.Additionally,the combined mode of Bragg fiber grating sensor and temperature measurement fiber was employed to explore the effect of vibration pretreatment on the strain process during microwave curing.The study results revealed that the change in vibration pretreatment temperature had a slight impact on the fiber weight content when the vibration acceleration remained constant.The metallographic and interlaminar strength of the specimen formed at a vibration pretreatment temperature of 80℃ demonstrated a porosity of 0.414% and a 10.69% decrease in interlaminar shear strength compared to autoclave curing.Moreover,the introduction of the vibration energy field during the microwave curing process led to a significant reduction in residual strain in both the 0°and 90°fiber directions,when the laminate was cooled to 60℃.

Tomographic velocity inversion for ADCIGs in areas with a rugged surface

Pre-stack depth migration velocity analysis is one of the key techniques influencing image quality. As for areas with a rugged surface and complex subsurface, conventional prestack depth migration velocity analysis corrects the rugged surface to a known datum or designed surface velocity model on which to perform migration and update the velocity. We propose a rugged surface tomographic velocity inversion method based on angle-domain common image gathers by which the velocity field can be updated directly from the rugged surface without static correction for pre-stack data and improve inversion precision and efficiency. First, we introduce a method to acquire angle-domain common image gathers （ADCIGs） in rugged surface areas and then perform rugged surface tornographic velocity inversion. Tests with model and field data prove the method to be correct and effective.

Comprehensive evaluation method for superstructures of prestressed concrete girder bridges

A multi-level evaluation model for the superstructure of a damaged prestressed concrete girder or beam bridge is established, and the evaluation indices of the model as well as the rating standards are defined. A normal relative function about the evaluation indices of each element is developed to calculate the relative degree, and for each element there are no sub-level elements. When evaluating the elements in the sub-item level or the index level of the model, the weights of elements pertain to one adopted element, taking into account their degrees of deterioration. Since the relative degrees and structure evaluation scales on the damage conditions are applied to characterize the superstructure of damaged prestressed concrete girder bridges, this method can evaluate the prestressed structure in detail, and the evaluation results agree with the Code for Maintenance of Highway Bridges and Culvers （JTG Hll--2004 ）. Finally, a bridge in Jilin province is taken as an example, using the method developed to evaluate its damage conditions, which gives an effective way for bridge engineering.

Synthetical condition assessment of long span suspension bridge based on closeness degree and FAHP

Based on the theory of pattern recognition, the concept of closeness degree between fuzzy sets is brought into the condition assessment of long span bridges. Using the fuzzy analytic hierarchy process （FAHP）, a mathematical model of a multi-objective assessment of a long span suspension bridge is set up. An example is given to show the procedure in the synthetical condition assessment of the Runyang Suspension Bridge, which includes the hierarchical division, the definition of factor weights and fuzzy membership functions, and the calculation of closeness degrees, etc. The assessment combines both the data from the health monitoring system and the manual tests. The classification of evaluation items as well as the calculation of deterministic and nondeterministic items is presented. Compared with the traditional method of point rating, this method can better describe the discreteness of monitoring data and the fuzziness in the condition assessment.

Extracting and evaluating method of web dense cores

This paper focuses on some key problems in web community discovery and link analysis.Based on the topic-oriented technology,the characteristics of a bipartite graph are studied.An Х bipartite core set is introduced to more clearly define extracting ways.By scanning the topic subgraph to construct Х bipartite graph and then prune the graph with i and j ,an Х bipartite core set,which is also the minimum element of a community,can be found.Finally,a hierarchical clustering algorithm is applied to many Х bipartite core sets and the dendrogram of the community inner construction is obtained.The correctness of the constructing and pruning method is proved and the algorithm is designed.The typical datasets in the experiment are prepared according to the way in HITS（hyperlink-induced topic search）.Ten topics and four search engines are chosen and the returned results are integrated.The modularity,which is a measure of the strength of the community structure in the social network,is used to validate the efficiency of the proposed method.The experimental results show that the proposed algorithm is effective and efficient.

基于Bregman分离执行算法的稀疏角度相位衬度计算层析重建

相位衬度成像及其计算层析(CT)技术不同于传统的吸收衬度成像,是一种新型的X射线成像技术,因具有高灵敏度、高衬度分辨率、能对软组织成像等特点而受到广泛关注。鉴于相位衬度CT往往导致非常长的辐射时间和巨大的辐射剂量,而稀疏角度重建在降低辐射剂量方面又有着非常明显的优势,因此,研究针对相位衬度CT的稀疏角度重建算法就变得非常有意义。近年来,针对解决稀疏重建的Bregman算法在图像处理方面被广泛应用。将Bregman分离执行(BOS)算法引入到微分相位衬度CT中,提出了一种稀疏角度相位衬度CT的交替迭代重建算法。数值模拟和实验表明,该方法可以在少量的投影数据下获得较好的重建效果。

Passive seismic velocity tomography on longwall mining panel based on simultaneous iterative reconstructive technique (SIRT)

Mining operation, especially underground coal mining, always has the remarkable risks of ground control. Passive seismic velocity tomography based on simultaneous iterative reconstructive technique （SIRT） inversion is used to deduce the stress redistribution around the longwall mining panel. The mining-induced microseismic events were recorded by mounting an array of receivers on the surface, above the active panel. After processing and filtering the seismic data, the three-dimensional tomography images of the p-wave velocity variations by SIRT passive seismic velocity tomography were provided. To display the velocity changes on coal seam level and subsequently to infer the stress redistribution, these three-dimensional tomograms into the coal seam level were sliced. In addition, the boundary element method （BEM） was used to simulate the stress redistribution. The results show that the inferred stresses from the passive seismic tomograms are conformed to numerical models and theoretical concept of the stress redistribution around the longwall panel. In velocity tomograms, the main zones of the stress redistribution arotmd the panel, including front and side abutment pressures, and gob stress are obvious and also the movement of stress zones along the face advancement is evident. Moreover, the effect of the advance rate of the face on the stress redistribution is demonstrated in tomography images. The research result proves that the SIRT passive seismic velocity tomography has an ultimate potential for monitoring the changes of stress redistribution around the longwall mining panel continuously and subsequently to improve safety of mining operations.

基于L^1范数和曲波系数双约束的稀疏角度微分相位衬度计算机层析成像重建方法

微分相位衬度计算机层析成像法(DPC-CT)是一种新的X射线无损检测方法。与传统方法相比,该方法在检测弱吸收物质时优势明显。但DPC-CT技术需要进行多次扫描后才能获取足够的样品信息,这必将导致很长的辐射时间和巨大的辐射剂量。因此,研究在稀疏角度条件下的DPC-PC重建算法就显得尤为重要。分析了DPCCT的特点,在凸集投影(POCS)的理论框架下,将L1范数、曲波系数约束和经典的代数迭代算法(ART)相结合提出了一种适合DPC-CT的重建算法。数值模拟和实验的结果表明,该方法可以根据少量投影数据获得较好的重建结果。

Response of upper ocean currents to typhoons at two ADCP moorings west of the Luzon Strait

We deployed two ADCP mooring systems west of the Luzon Strait in August 2008,and measured the upper ocean currents at high frequency.Two typhoons passed over the moorings during approximately one-month observation period.Using ADCP observations,satellite wind and heat flux measurements,and high-resolution model assimilation products,we studied the response of the upper ocean to typhoons.The first typhoon,Nuri,passed over one of the moorings,resulting in strong Ekman divergence and significant surface cooling.The cooling of surface water lagged the typhoon wind forcing about one day and lasted about five days.The second typhoon,Sinlaku,moved northward east of the Luzon Strait,and did not directly impact currents near the observation regions.Sinlaku increased anomalous surface water transport exchange across the Luzon Strait,which modulated the surface layer current of the Kuroshio.

Mathematical modeling of salt-gradient ion-exchange simulated moving bed chromatography for protein separations

The salt-gradient operation mode used in ion-exchange simulated moving bed chromatography (SMBC) can improve the efficiency of protein separations. A detailed model that takes into account any kind of adsorption/ion-exchange equilibrium, salt gradient, size exclusion, mass transfer resistance, and port periodic switching mechanism, was developed to simulate the complex dynamics. The model predictions were verified by the experimental data on upward and downward gradients for protein separations reported in the literature. All design and operating parameters (number, configuration, length and diameter of columns, particle size, switching period, flow rates of feed, raffinate, desorbent and extract, protein concentrations in feed, different salt concentrations in desorbent and feed) can be chosen correctly by numerical simulation. This model can facilitate the design, operation, optimization, control and scale-up of salt-gradient ion-exchange SMBC for protein separations.

Thermal and concentration analysis of Phan-Thien-Tanner fluid flow due to ciliary movement in a peripheral layer

This paper presents the analysis of two-layer cilia induced flow of Phan-Thien-Tanner(PTT) fluid with thermal and concentration effect.The Phan-Thien-Tanner fluid model has been used in the analogy of mucus present in the respiratory tract.The two-layer model approach was used due to the Peri Ciliary liquid Layer(PCL) and Airway Ciliary Layer(ACL) present on the epithelium cell in respiratory tract.The mathematical modelling of two-layer flow problem was simplified using long wavelength and small Reynold ’ s number approximation.The resulting differential equation with moving boundary gives exact solution for velocity,temperature and concentration profiles in two layers.The change in pressure has calculated by the results of velocity profile,also the pressure rise was evaluated by the numerical integration of pressure gradient along the channel wall.The impact of physical parameters on pressure rise,velocity,temperature and concentration profile was explained by the graphs.It can be seen from graphs that velocity and temperature profile are maximum in the inner layer of fluid(PCL) and concentration profile is maximum at outer layers of fluid(ACL).

Location of high seismic activity zones and seismic hazard assessment in Zabrze Bielszowice coal mine using passive tomography

In the paper results of passive tomography calculations have been presented to assess rockburst hazard and locate high seismic activity zones in the vicinity of longwall 306 in Zabrze Bielszowice coal mine. The area of study was 1000 m in X direction by 900 m in Y direction. The zones of high values of P-wave propagation velocity have been found to correlate with the distribution of large seismic tremors.

Pore structure of ore granular media by computerized tomography image processing

The pore structure images of ore particles located at different heights of leaching column were scanned with X-ray computerized tomography (CT) scanner, the porosity and pore size distribution were calculated and the geometrical shape and connectivity of pores were analyzed based on image process method, and the three dimensional reconstruction of pore structure images was realized. The results show that the porosity of ore particles bed in leaching column is 42.92%, 41.72%, 39.34% at top, middle and bottom zone, respectively. Obviously it has spatial variability and decreases appreciably along the height of the column. The overall average porosity obtained by image processing is 41.33% while the porosity gotten from general measurement method in laboratory is 42.77% showing the results of both methods are consistent well. The pore structure of ore granular media is characterized as a dynamical space network composed of interconnected pore bodies and pore throats. The ratio of throats with equivalent diameter less than 1.91 mm to the total pores is 29.31%, and that of the large pores with equivalent diameter more than 5.73 mm is 2.90%.

Application of Electrical Capacitance Tomography to the Concentration Measurement in a Cyclone Dipleg

Accurate solid concentration measurement plays a key role in the process industry. Measurements analyzed offline can be used to estimate process efficiencies, to identify problems in a flow, and to validate computational models. Online measurements can be used for active control. Electrical capacitance tomography （ECT） is a unique measuring technique with great potential in multiphase flow measurement. Experimental studies are carried out on a solid concentration measurement in a cyclone separator dipleg, using ECT. In this experiment eight electrodes are selected for the ECT sensor that is placed on the straight tube of the dipleg. The fluctuating characteristics according to the screw feeder and the effect of the airflow rate from the top of the cyclone are analyzed. The feasibility andreliability of the method are verified by the experimental results.

Traveltime tomography and prestack depth migration for vertical seismic profiling of an angle-domain walkaway on a complex surface

Walkaway VSP cannot obtain accurate velocity field,as it asymmetrically reflects ray path and provides uneven coverage to underground target,thereby presenting issues related to imaging quality.In this study,we propose combining traveltime tomography and prestack depth migration for VSP of an angle-domain walkaway,in a bid to establish accurate two-dimensional and three-dimensional(3 D)velocity models.First,residual curvature was defined to update velocity,and an accurate velocity field was established.To establish a high-precision velocity model,we deduced the relationship between the residual depth and traveltime of common imaging gathers(CIGs)in walkaway VSP.Solving renewal velocity using the least squares method,a four-parameter tomographic inversion equation was derived comprising formation dip angle,incidence angle,residual depth,and sensitivity matrix.In the angle domain,the reflected wave was divided into up-and down-transmitted waves and their traveltimes were calculated.The systematic cumulative method was employed in prestack depth migration of a complex surface.Through prestack depth migration,the offset-domain CIGs were obtained,and dip angle was established by defining the stack section horizon.Runge–Kutta ray tracing was employed to calculate the ray path from the reflection point to the detection point,to determine the incident angle,and to subsequently calculate the ray path from the reflection point to the irregular surface.The offset-domain residual depths were mapped to the angle domain,and a new tomographic equation was established and solved.Application in the double complex area of the Tarim Basin showed the four-parameter tomographic inversion equation derived in this paper to be both correct and practical and that the migration algorithm was able to adapt to the complex surface.