Numerical Analysis of Explosion Characteristics of Vent Gas From 18650 LiFePO_(4) Batteries With Different States of Charge

The combustion and explosion characteristics of lithium-ion battery vent gas is a key factor in determining the fire hazard of lithium-ion batteries.Investigating the combustion and explosion hazards of lithium-ion batteries vent gas can provide guidance for rescue and protection in explosion accidents in energy storage stations and new energy vehicles,thereby promoting the application and development of lithium-ion batteries.Based on this understanding and combined with previous research on gas production from lithium-ion batteries,this article conducted a study on the combustion and explosion risks of vent gas from thermal runaway of 18650 LFP batteries with different states of charge(SOCs).The explosion limit of mixed gases affected by carbon dioxide inert gas is calculated through the“elimination”method,and the Chemkin-Pro software is used to numerically simulate the laminar flame speed and adiabatic flame temperature of the battery vent gas.And the concentration of free radicals and sensitivity coefficients of major elementary reactions in the system are analyzed to comprehensively evaluate the combustion explosion hazard of battery vent gas.The study found that the 100%SOC battery has the lowest explosion limit of the vent gas.The inhibitory elementary reaction sensitivity coefficient in the reaction system is lower and the concentration of free radicals is higher.Therefore,it has the maximum laminar flame speed and adiabatic flame temperature.The combustion and explosion hazard of battery vent gas increases with the increase of SOC,and the risk of explosion is the greatest and most harmful when SOC reaches 100%.However,the related hazards decrease to varying degrees with overcharging of the battery.This article provides a feasible method for analyzing the combustion mechanism of vent gas from lithium-ion batteries,revealing the impact of SOC on the hazardousness of battery vent gas.It provides references for the safety of storage and transportation of lithium-ion batteries,safety protection of energy storage stations,and the selection of related fire extinguishing agents.

行波管电子枪数值模拟设计的判定

提出了采用数值软件模拟法进行行波管电子枪设计时对电子注质量好坏的判断准则:电子枪应具有更好的阴极表面电子发射密度均匀性、电子注层流性、注腰位置附近电子注径向密度分布均匀性及某百分比电子注包络曲线的光滑性等。利用编写的软件对某行波管电子枪进行数值模拟设计时,不断调整电子枪的结构,应用以上设计准则,通过对电子注质量进行判定和比较,得到了相对更符合设计要求的电子枪结构。

应用于电流量子化的电子束优化

利用粒子加速器产生的电子束实现电流量子化是电学计量领域新兴方向,要求电子束稳定度高和精确可调以满足不同计量范围的要求。电子枪产生的电子束品质决定了电流量子化系统的性能。为保障电子束的精准传输和准确调节,对束流的横向发射度,即直流束流的层流性提出了严格的要求。因此,从电子束的引出和传输两个过程对电子束层流性进行了优化。主要包括基于束流动力学分析优化设计电子枪电磁结构,以及设计螺线管线圈抑制电子束传输过程中的横向发射度增长。针对线圈边缘磁场问题,比较分析了屏蔽壳和反抵线圈两种补偿方案,并通过仿真验证了其效果。该研究将为基于加速器技术的电流量子化的工程实现提供方案,并促进该技术的发展。

Analytical Solution for Laminar Viscous Flow inthe Gap Between Two Parallel Rotary Disks

Aim To get the analytical for laminar viscous flow in the gap of two parallel rotating disks. Methods By estimating the order of magnitude of each term in the Navier-Stokes equations to drop small terms and achieve the required simplified differential equations, and by integrating the equations to obtain the solution for theflow between two rotary disks. Results Parameters related to the laminar viscous flow in the gap between two parallel rotary disks, such as the velocity, the pressure, the flowrate, the force, the shearing stress, the torque and the power derived. Conclusion The result provides a theoretical basis and an effective method for the designs of the devices connected with the laminar viscous flow in the gap between two parallel rotary disks.

FURTHER OBSERVATIONS OF LATE TRANSITION PROCESSES IN CROSSFLOW INSTABILITY EXPERIMENT

The experiments of primary and secondary instabilities with controlled excitation are carried out on a swept flat plate to study the process leading to the final breakdown of laminar flow. Two types of high frequency secondary instabilities are identified. The most amplified mode is centered about the inflection point of the crosswise profile of the boundary layer and is interpreted as inflectional instability, the other occurs in the one third of the boundary layer from the wall. The high frequency disturbances are highly amplified but they also saturate similarly to the primary and nonlinearly generated disturbances. Their main effect in the final breakdown seems interact with the disturbances is developed and thus widens the frequency spectrum to turbulent state.

Dynamic hierarchy description and constraint rules of flexibility workflow

A dynamic hierarchical description method for workflow is presented. The method provides a dynamic hierarchical way to define a workflow with non-determinate or dynamic factors. With this method, the main process defined at build-time can be reified and extended by the principle of the sub-organizations at either the build-time or the run-time. To ensure the consistency and integrity of the description, a series of constraint rules are also discussed to realize seamless integration between a decomposed process and its original one. This approach supports the description of unpredictable uncertainties, the dynamic hierarchy of business process, and the dynamic modification of enterprise organizations, and all of these improve the flexibility and extendability of workflow management systems dramatically.

Effectof Neutral Traps on Tunneling Current and SILC in Ultrathin Oxide Layer

The effect of neutral trap on tunneling currentin ultrathin MOSFETs is investigated by num erical analy- sis.The barrier variation arisen by neutral trap in oxide layer is described as a rectangular potential well in the con- duction band of Si O2 .The different barrier variation of an ultrathin metal- oxide- sem iconductor(MOS) structure with oxide thickness of4nm is numerically calculated.It is shown that the effect of neutral trap on tunneling cur- rent can not be neglected.The tunneling current is increased when the neutral trap exists in the oxide layer.This simple m odel can be used to understand the occurring mechanism of stress induced leakage current.

NONPARALLEL BOUNDARY LAYER STABILITY IN HIGH SPEED FLOWS

The parabolized stability equations （PSEs） for high speed flows, especially supersonic and hypersonic flows, are derived and used to analyze the nonparallel boundary layer stability. The proposed numerical techniques for solving PSE include the following contents： introducing the efficiently normal transformation of the boundary layer, improving the computational accuracy by using a high-order differential scheme near the wall, employing the predictor-corrector and iterative approach to satisfy the important normalization condition, and implementing the stable spatial marching. Since the second mode dominates the growth of the disturbance in high Mach number flows, it is used in the computation. The evolution and characteristics of the boundary layer stability in the high speed flow are demonstrated in the examples. The effects of the nonparallelizm, the compressibility and the cooling wall on the stability are analyzed. And computational results are in good agreement with the relevant data.

Boundary layer flow of third grade nanofluid with Newtonian heating and viscous dissipation

Two-dimensional boundary layer flow of an incompressible third grade nanofluid over a stretching surface is investigated.Influence of thermophoresis and Brownian motion is considered in the presence of Newtonian heating and viscous dissipation.Governing nonlinear problems of velocity, temperature and nanoparticle concentration are solved via homotopic procedure.Convergence is examined graphically and numerically. Results of temperature and nanoparticle concentration are plotted and discussed for various values of material parameters, Prandtl number, Lewis number, Newtonian heating parameter, Eckert number and thermophoresis and Brownian motion parameters. Numerical computations are performed. The results show that the change in temperature and nanoparticle concentration distribution functions is similar when we use higher values of material parameters β1 andβ2. It is seen that the temperature and thermal boundary layer thickness are increasing functions of Newtonian heating parameter γ.An increase in thermophoresis and Brownian motion parameters tends to an enhancement in the temperature.

某层流机翼验证机跨声速层流特性敏感性分析

采用雷诺平均Navier-Stokes (RANS)方法结合基于当地变量的γ-Reθ转捩预测模型,针对某特殊布局形式的层流机翼验证机开展跨声速层流特性和参数敏感性分析。通过DLR F-5三维机翼构型对基于RANS的转捩预测方法进行算例验证分析,同时将某层流验证机中央翼段层流转捩预测结果与试验进行对比,证明了采用的计算方法完全适用于所研究问题。研究重点关注全机巡航状态附近的气动特性和中央验证段在不同飞行状态下的表面转捩位置及层流区长度。通过计算,进一步分析了层流流动对全机升阻及力矩特性的影响。结果表明:马赫数、雷诺数、来流湍流度、迎角等均会对中央验证段表面转捩位置产生明显的影响,影响规律差异较大。马赫数的增加会引起压力分布的较大变化,使转捩位置前后波动;雷诺数按同样幅度递增会使翼面转捩位置有规律地提前;来流湍流度和迎角的增加会导致转捩提前,层流区长度明显缩小。

Stability of Stratified Gas-Liquid Flow in Horizontal and Near Horizontal Pipes

A viscous Kelvin-Helmholtz criterion of the interfacial wave instability is proposed in this paper based on the linear stability analysis of a transient one-dimensional two-fluid model. In thismodel, the pressure is evaluated using the local momentum balance rather than the hydrostatic approximation. The criterion predicts well the stability limit of stratified flow in horizontal and nearly horizontal pipes. The experimental and theoretical investigation on the effect of pipe inclination on the interfacial instability are carded out. It is found that the critical liquid height at the onset of interfacial wave instability is insensitive to the pipe inclination. However, the pipe inclination significantly affects critical superficial liquid velocity and wave velocity especially lor low gas velocities.

Laminar Flow and Heat Transfer Characteristics in Jackets of Triangular Flow Channels

Laminar flow and heat transfer characteristics of jacketed vessel with triangular flow channels were numerically studied under hydrodynamically and thermally fully developed conditions. Constant heat flux at theheated wall was assumed. The numerical program code interms of vorticity, stream function, axial velocity com ponent and energy equations was written based on a finite volume method. Based on the numerical results, the flow and temperature field were given, and the effects of Dean and Prandtl numbers on flow and heat transfer were ex amined, and the correlations of flow resistance and mean Nusselt number were developed for the jacket. The results show that the structure of secondary flow is steady two vortices in the investigated range of dimensionless curvatureratio and Reynolds number. Two peaks of local Nusselt number increase significantly with Prandtl and Dean num ber increasing, but the local Nusselt numbers near two ends and at the center of the heated wall increase only slightly. The center and two ends of heated wall are the poor positions for heat transfer in the jacket. Compared with the outer half coil jacket at the same area of heated wall, curvature radius, Reynolds number and Prandtl number, e jacket of triangular flow chmnel has lower flow resistance and less mean Nusselt number.

Assessment of Coronary Stents by 64-slice Computed Tomography: In-stent Lumen Visibility and Patency

Objective To assess lumen visibility of coronary stents by 64-slice computed tomography （CT） coronary angiography, and determine the value of 64-slice CT in non-invasive detecting of in-stent restenosis after coronary artery stent implantation. Methods Totally, 60 patients （54 males, aged 57.0±12.7 years） and /05 stents were investigated by 64-slice CT at a mean interval of 20.0±16.6 months after coronary stents implantation. Axial multi-planar reconstruction images of the stents and curved-planar reconstruction images through the median of the stents were reconstructed for evaluating stent image quality on a 5-point scale （1=excellent, 5=nonassessable）, and stent lumen diameter was detected. Conventional coronary angiography was performed in 18 patients, and 32 stents were evaluated. Results Image quality was good to excellent on average （score 1.71±0.76）. Stent image quality score was correlated to heart rate （r=0. 281, P〈0.01） and stent diameter （r=-0.480, P〈0.001）. All the stents were assessable in lumen visibility with an average visible lumen diameter percentage of 60.7%±13.6%. Visible lumen diameter percentage was correlated to heart rate （r=-0.193, P〈0.05）, stent diameter （r=0.403, P〈0.001）, and stent image quality score （r=-0.500, P〈0.001）. Visible lumen diameter percentage also varied depending on the stent type. In comparison with the conventional coronary angiography, 4 of 6 in-stent stenoses were correctly detected. The sensitivity and specificity for the detection of in-stent stenosis were 66.7% and 84.6%, respectively. Conclusions Using a 64-slice CT, the stent lumen is partly visible in most of the stents. And 64-slice CT may be useful in the assessment of stent patency.

A New Coupled KdV Equation： Painlevé Test

A new type of coupled Korteweg de-Vries equation is found to be Painlevé-integrable. The new model is a special case which can be used to describe two-layer fluids with different dispersion relations.

Analysis of the variations in the strength and position of stratospheric sudden warming in the past three decades

The authors investigate the statistical features of variations in the strength and position of stratospheric sudden warming (SSW) in the Northern Hemisphere based on ERA-Interim data from 1979 to 2016. It is found that there are 55 SSW events in the past 38 years (average: 1.4 times per year), including 33 major SSW events and 22 minor SSW events. The events mainly occur in February. The variations of the maximum meridional gradient of the zonal mean temperature of the SSW events show increasing trends from 1979 to 1983 and from 1998 to 2011, and decreasing trends from 1984 to 1997 and from 2012 to 2016. However, the linear trend of the variations in the past three decades shows a negative trend. Meanwhile, the strength and duration of major SSW events show similar features. Some SSW events occur at nearly the same time at different levels from 100 hPa to 10 hPa, while others first occur at 10 hPa and then the signal propagates downwards to lower levels. A very interesting phenomenon is that the maximum temperature centers of these 55 SSW events are mainly located over the Eurasian continent between 30°E and 120°E. This may be related to a polar vortex shifting to the Eurasian continent in the past three decades.

On Symmetry Flows of Noncommutative Kadomtsev-Petviashvili Hierarchy

We discuss symmetry flows of noncommutative Kadomtsev-Petviashvili (NCKP) hierarchy. An operatorbased formulation, alternative to the star-product approach of extended symmetry flows is presented. Noncommutative additional symmetry flows of the NCKP hierarchy are formulated. A rescaling symmetry flow which is associated with the rescaling of whole coordinates is introduced.

Slip flow and variable properties of viscoelastic fluid past a stretching surface embedded in a porous medium with heat generation

This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid properties, slip velocity, and internal heat generation/absorption. The flow in boundary layer is considered to be generated solely by the stretching of the sheet adjacent to porous medium with boundary wall slip condition. Highly nonlinear momentum and thermal boundary layer equations governing the flow and heat transfer are reduced to set of nonlinear ordinary differential equations by appropriate transformation. The resulting ODEs are successfully solved numerically with the help of shooting method. Graphical results are shown for non-dimensional velocities and temperature. The effects of heat generation/absorption parameter, the porous parameter, the viscoelastic parameter, velocity slip parameter, variable thermal conductivity and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction coefficient and Nusselt number are presented. Comparison of numerical results is made with the earlier published results under limiting cases.

Schroedinger Flows to Symmetric Spaces and the Second Matrix-AKNS Hierarchies

This article gives a unified geometric interpretation of the second Matrix-AKNS hierarchies via Schroedinger flows to symmetric spaces of Kaehler and paraKaehler types.

Laminar natural convection characteristics in an enclosure with heated hexagonal block for non-Newtonian power law fluids

This work illustrates the steady state, two dimensional natural convective flow and heat transfer features in square enclosure containing heated hexagonal block maintained either at constant wall temperature(CWT) or uniform heat flux(UHF) thermal conditions. Governing equations(mass, momentum and energy) are solved by using finite volume method(FVM) with 3rd order accurate QUICK discretization scheme and SIMPLE algorithm for range of field pertinent parameters such as, Grashof number(10~3≤ Gr ≤ 10~6), Prandtl number(1 ≤ Pr ≤ 100) and power law index(0.5 ≤ n ≤ 1.5). The analysis of momentum and heat transfer characteristics are delineated by evolution of streamlines, isotherms, variation of average Nusselt number value and Colburn factor for natural convection(j_(nH)). A remarkable change is observed on fluid flow and thermal distribution pattern in cavity for both thermal conditions. Nusselt number shows linear variation with Grashof and Prandtl numbers; while rate of heat transfer by convection decreases for power law index value. Higher heat transfer rate can be achieved by using uniform heat flux condition. A Nusselt number correlation is developed for possible utilization in engineering/scientific design purpose.

Evolution of diagenetic fluid of ultra-deep Cretaceous Bashijiqike Formation in Kuqa depression

Diagenetic fluid types of the Cretaceous Bashijiqike formation are restored based on the analysis of petrographic,electron microprobe composition,inclusions homogenization temperature,salinity and vapor composition and laser carbon and oxygen isotope of diagenetic mineral,and regional geological background.Diagenetic fluid evolution sequence is analyzed on this basis.The crystalline dolomite cement has a low concerntration of Sr,high concerntration of Mn and higher carbon isotope,showing that the crystalline dolomite is affected by meteoric fresh water,associated with the tectonic uplift of late Cretaceous.Similarδ13CPDB,negative transfer ofδ18OPDB and the differentiation of the concerntration of Fe and Mn indicate that the diagenetic fluid of the vein dolomite cement is homologous with the diagenetic fluid of the crystalline dolomite cement,temperature and depth are the dominant factors of differential precipitation between these two carbonate cements.Anhydrite cements have high concerntration of Na,extremely low concerntration of Fe and Mn contents.Based on these data,anhydrite cements can be thought to be related to the alkaline fluid overlying gypsum-salt layer produced by dehydration.The barite vein has abnormally high concerntration of Sr,ultra-high homogenization temperature and high-density gas hydrocarbon inclusions,which is speculated to be the forward fluid by intrusion of late natural gas.Coexistence of methane inclusions with CO2 gas proves existence of acid water during the accumulation of natural gas in the late stages.Therefore,the alkaline environment and associated diagenesis between the meteoric fresh water in epidiagentic stage and carbonic acid in the late diagenesis have dominated the process of diagenesis and reservoir,the secondary porosity and fracture zone formed by gas accumulation is a favorable play for the exploration of ultra-deep reservoirs.