Tensile properties of a Re-containing single crystal superalloy were determined within the temperature range from 20 to 1 100 ℃with a constant strain rate of 1.67 ×10^-4 s^-1.From room temperature to 600 ℃,the ...Tensile properties of a Re-containing single crystal superalloy were determined within the temperature range from 20 to 1 100 ℃with a constant strain rate of 1.67 ×10^-4 s^-1.From room temperature to 600 ℃,the yield strength increases slightly with increasing temperature.The yield strength decreases to aminimum at 760 ℃,while a maximum is reached dramatically at 800 ℃.The elongation and area reduction decrease gradually from room temperature to 800 ℃.Above 800 ℃,the yield strength decreases significantly with increasing temperature.The γ＇ phase is sheared by antiphase boundary （APB） below 600 ℃while elongated SSF （superlattice stacking fault） is left in γ＇ as debris.At 760 ℃the γ＇ phase is sheared by a/3 112 superpartial dislocation,which causes decrease of yield strength due to low energy of SSF.Above 800 ℃dislocations overcome γ＇ through by-passing mechanism.展开更多
The as-cast microstructure of AE42 was of typical dendritic and composed of the a matrix and some needle-shaped interphases Al11RE3. A small mount of Ca addition results in significant microstructural refinement and f...The as-cast microstructure of AE42 was of typical dendritic and composed of the a matrix and some needle-shaped interphases Al11RE3. A small mount of Ca addition results in significant microstructural refinement and formation of a Al2Ca phase, which showed two kinds of morphologies, lamellar and tiny granular. The former distributes on grain boundaries and the later is within the matrix grains. With the increase of Ca addition the volume fraction of Al-RE compound (Al11RE3) decreases, but Al2Ca increases. Addition of Ca causes a significant increase of yield strength of the alloy both at ambient and elevated temperatures, but a little decrease of the ductility. With calcium addition the ultimate strength decreases at ambient temperature and 150°t, but increases at 175°C and 200°C.展开更多
Ultrafine grain pure aluminum was produced by equal channel angular pressing and cold rolling, the deformed aluminum was annealed at 200 ℃ for 1 h. The tensile curves of deformed and annealed aluminum show that yield...Ultrafine grain pure aluminum was produced by equal channel angular pressing and cold rolling, the deformed aluminum was annealed at 200 ℃ for 1 h. The tensile curves of deformed and annealed aluminum show that yield strength of deformed aluminum increases by 100%-300% and its elongation decreases by about 20%. After low temperature annealing, strength of annealed aluminum increases by 20% and elongation decreases by over 50%, the recovery of dislocations may be the main cause of annealing strengthening. In addition, there is an abrupt stress drop in the tensile curves of annealed aluminum and the formation of shear band is responsible for it.展开更多
The influence of impurities on damping capacities of ZK60 magnesium alloys in the as-cast,as-extruded and T4-treated states was investigated by dynamically mechanical analyzer at room temperature.Granato and Lucke dis...The influence of impurities on damping capacities of ZK60 magnesium alloys in the as-cast,as-extruded and T4-treated states was investigated by dynamically mechanical analyzer at room temperature.Granato and Lucke dislocation pinning model was employed to explain damping properties of the alloys.It is found that reducing impurity content can decrease the amount of second-phase particles,increase grain size and improve damping capacity of the as-cast alloy slightly.The as-extruded alloy with lower impurity content is found to possess obviously higher damping capacity in the relatively high strain region than that with higher impurity concentration,which appears to originate mainly from different dislocation characteristics.The variation tendency of damping property with change of impurity content after solution-treatment is also similar to that in the as-extruded and as-cast states. Meanwhile,the purification of the alloy results in an evident improvement in tensile yield strength in the as-extruded state.展开更多
Flexibility of the CSIR-RCS, induction stirring with simultaneous air cooling process, in combination with high pressure die casting is successfully demonstrated by semi-solid rheocasting of plates performed on commer...Flexibility of the CSIR-RCS, induction stirring with simultaneous air cooling process, in combination with high pressure die casting is successfully demonstrated by semi-solid rheocasting of plates performed on commercial 2024, 6082 and 7075 wrought aluminum alloys. Tensile properties were measured for the above mentioned rheocast wrought aluminum alloys in the T6 condition. The results showed that tensile properties were close to or even in some cases exceeded the minimum specifications. The yield strength and elongation of rheocast 2024-T6 exceeded the minimum requirements of the wrought alloy in the T6 condition but the ultimate tensile strength achieved only 90% of the specification because the Mg content of the starting alloy was below the commercial alloy specification. The strengths of rheocast 6082-T6 exceeded all of the wrought alloy T6 strength targets but the elongation only managed 36% of the required minimum due to porosity, caused by incipient melting during solution heat treatment, and the presence of fine intermetallie needles in the eutectic. The yield strength of rheocast 7075 exceeded the required one and the ultimate tensile strength also managed 97% of the specification; while the elongation only reached 46% of the minimum requirement also due to incipient melting porosity caused during the solution heat treatment process.展开更多
Both Mg-1Mn-3.5Y and Mg-1Mn-1Y-2.5Nd alloys（mass fraction,%）were extruded at 380？C.Most of the（10^-10） crystal planes in the Mg-1Mn-3.5Y alloy are parallel to the normal direction,while most of the（10^-11）cryst...Both Mg-1Mn-3.5Y and Mg-1Mn-1Y-2.5Nd alloys（mass fraction,%）were extruded at 380？C.Most of the（10^-10） crystal planes in the Mg-1Mn-3.5Y alloy are parallel to the normal direction,while most of the（10^-11）crystal planes in the Mg-1Mn-1Y-2.5Nd alloy are parallel to the normal direction.The tensile tests at room temperature,100℃ and 200℃ show that the Mg-1Mn-3.5Y alloy exhibits higher yield strength,but lower elongation to failure as compared with the Mg-1Mn-1Y-2.5Nd alloy. These differences in the tensile mechanical properties between the two alloys are mainly attributed to their different texture types and amount and distribution of the Mg24Y5 precipitates.The serration flow behavior is observed in the Mg-1Mn-1Y-2.5Nd alloy at 200℃,but does not occur in the Mg-1Mn-3.5Y alloy.The Mg-1Mn-3.5Y alloy shows the cleavage fracture mode,while the Mg-1Mn-1Y-2.5Nd alloy exhibits the dimple fracture mode.展开更多
基金Project(2010CB631206) supported by the National Basic Research Program of ChinaProject(50931004) supported by the National Natural Science Foundation of China
文摘Tensile properties of a Re-containing single crystal superalloy were determined within the temperature range from 20 to 1 100 ℃with a constant strain rate of 1.67 ×10^-4 s^-1.From room temperature to 600 ℃,the yield strength increases slightly with increasing temperature.The yield strength decreases to aminimum at 760 ℃,while a maximum is reached dramatically at 800 ℃.The elongation and area reduction decrease gradually from room temperature to 800 ℃.Above 800 ℃,the yield strength decreases significantly with increasing temperature.The γ＇ phase is sheared by antiphase boundary （APB） below 600 ℃while elongated SSF （superlattice stacking fault） is left in γ＇ as debris.At 760 ℃the γ＇ phase is sheared by a/3 112 superpartial dislocation,which causes decrease of yield strength due to low energy of SSF.Above 800 ℃dislocations overcome γ＇ through by-passing mechanism.
文摘The as-cast microstructure of AE42 was of typical dendritic and composed of the a matrix and some needle-shaped interphases Al11RE3. A small mount of Ca addition results in significant microstructural refinement and formation of a Al2Ca phase, which showed two kinds of morphologies, lamellar and tiny granular. The former distributes on grain boundaries and the later is within the matrix grains. With the increase of Ca addition the volume fraction of Al-RE compound (Al11RE3) decreases, but Al2Ca increases. Addition of Ca causes a significant increase of yield strength of the alloy both at ambient and elevated temperatures, but a little decrease of the ductility. With calcium addition the ultimate strength decreases at ambient temperature and 150°t, but increases at 175°C and 200°C.
基金Project(gjd08011) supported by Shanghai Municipal Education Commission,ChinaProject (J51402) supported by Shanghai Leading Academic Discipline,China
文摘Ultrafine grain pure aluminum was produced by equal channel angular pressing and cold rolling, the deformed aluminum was annealed at 200 ℃ for 1 h. The tensile curves of deformed and annealed aluminum show that yield strength of deformed aluminum increases by 100%-300% and its elongation decreases by about 20%. After low temperature annealing, strength of annealed aluminum increases by 20% and elongation decreases by over 50%, the recovery of dislocations may be the main cause of annealing strengthening. In addition, there is an abrupt stress drop in the tensile curves of annealed aluminum and the formation of shear band is responsible for it.
基金Project(50725413)supported by the National Natural Science Foundation of ChinaProject(2009BB4215)supported by the Natural Science Foundation of Chongqing Science and Technology Commission,ChinaProject(2008AB4114)supported by the Major Program of Chongqing Science and Technology Commission,China
文摘The influence of impurities on damping capacities of ZK60 magnesium alloys in the as-cast,as-extruded and T4-treated states was investigated by dynamically mechanical analyzer at room temperature.Granato and Lucke dislocation pinning model was employed to explain damping properties of the alloys.It is found that reducing impurity content can decrease the amount of second-phase particles,increase grain size and improve damping capacity of the as-cast alloy slightly.The as-extruded alloy with lower impurity content is found to possess obviously higher damping capacity in the relatively high strain region than that with higher impurity concentration,which appears to originate mainly from different dislocation characteristics.The variation tendency of damping property with change of impurity content after solution-treatment is also similar to that in the as-extruded and as-cast states. Meanwhile,the purification of the alloy results in an evident improvement in tensile yield strength in the as-extruded state.
文摘Flexibility of the CSIR-RCS, induction stirring with simultaneous air cooling process, in combination with high pressure die casting is successfully demonstrated by semi-solid rheocasting of plates performed on commercial 2024, 6082 and 7075 wrought aluminum alloys. Tensile properties were measured for the above mentioned rheocast wrought aluminum alloys in the T6 condition. The results showed that tensile properties were close to or even in some cases exceeded the minimum specifications. The yield strength and elongation of rheocast 2024-T6 exceeded the minimum requirements of the wrought alloy in the T6 condition but the ultimate tensile strength achieved only 90% of the specification because the Mg content of the starting alloy was below the commercial alloy specification. The strengths of rheocast 6082-T6 exceeded all of the wrought alloy T6 strength targets but the elongation only managed 36% of the required minimum due to porosity, caused by incipient melting during solution heat treatment, and the presence of fine intermetallie needles in the eutectic. The yield strength of rheocast 7075 exceeded the required one and the ultimate tensile strength also managed 97% of the specification; while the elongation only reached 46% of the minimum requirement also due to incipient melting porosity caused during the solution heat treatment process.
基金Project(50771049)supported by the National Natural Science Foundation of ChinaProject(2004CB619301)supported by the National Basic Research Program of China
文摘Both Mg-1Mn-3.5Y and Mg-1Mn-1Y-2.5Nd alloys（mass fraction,%）were extruded at 380？C.Most of the（10^-10） crystal planes in the Mg-1Mn-3.5Y alloy are parallel to the normal direction,while most of the（10^-11）crystal planes in the Mg-1Mn-1Y-2.5Nd alloy are parallel to the normal direction.The tensile tests at room temperature,100℃ and 200℃ show that the Mg-1Mn-3.5Y alloy exhibits higher yield strength,but lower elongation to failure as compared with the Mg-1Mn-1Y-2.5Nd alloy. These differences in the tensile mechanical properties between the two alloys are mainly attributed to their different texture types and amount and distribution of the Mg24Y5 precipitates.The serration flow behavior is observed in the Mg-1Mn-1Y-2.5Nd alloy at 200℃,but does not occur in the Mg-1Mn-3.5Y alloy.The Mg-1Mn-3.5Y alloy shows the cleavage fracture mode,while the Mg-1Mn-1Y-2.5Nd alloy exhibits the dimple fracture mode.
