Flotation column is widely used as the separation equipment for fine mineral due to its high selectivity. However, this device may be unsuitable for the coarse particle flotation and has high handling ability. A two-s...Flotation column is widely used as the separation equipment for fine mineral due to its high selectivity. However, this device may be unsuitable for the coarse particle flotation and has high handling ability. A two-stage flotation column with dimensions of 2 000 mm×1 000 mm×4 000 mm was designed to enhance the column flotation process. The energy input was modified by adjusting the flow rate and the head of circulating pump. The flotation column was designed with low energy input in the first stage(speed flotation stage) to recover easy-to-float materials quickly, and high energy input in the second stage(recovery stage) to recover difficult-to-float minerals compulsorily. Contrast experiments on the throughput and coarse coal recovery of high ash coal from the Kailuan Mine were conducted using conventional single-stage flotation column and the two-stage flotation column. The results show that the combustible matter recovery of the two-stage flotation column is 5.25% higher than that of the conventional single-stage flotation column. However, the ash contents of clean coal for both columns are similar. Less coarse coals with low ash are obtained using the two-stage flotation column than that using the single-stage column flotation with the same handling ability. The two-stage flotation column process can enhance coal flotation compared with the conventional single-stage column flotation.展开更多
With concentrated juice of mulberry as raw material, the influence of type and dosage of dry aid, the inlet air tempera- ture, inlet flow rate, and rotating speed on spray drying was studied. The spray drying processi...With concentrated juice of mulberry as raw material, the influence of type and dosage of dry aid, the inlet air tempera- ture, inlet flow rate, and rotating speed on spray drying was studied. The spray drying processing conditions of mulberry pow- der were optimized by the L9 （3^4） orthogonal test on the basis of single factor experiment. The results showed that optimum technical parameters to produce mulberry powder were： lS-cyclodextrin as dry aids with dosage of 30%, inlet air temperature of 180 ℃, rotating speed of 18 000 r/min and inlet flow rate of 30 mL/min. The mulberry powder under this optimum process conditions had a loose structure and bright color, fruity flavor was rich, the anthocyanin content for 54.67 mg/g, moisture content for 5.6% and sensory scores for 83.展开更多
To avoid the machine problems of excessive axial force, complex process flow and frequent tool changing during robotic drilling holes, a new hole-making technology (i.e., helical milling hole) was introduced for desig...To avoid the machine problems of excessive axial force, complex process flow and frequent tool changing during robotic drilling holes, a new hole-making technology (i.e., helical milling hole) was introduced for designing a new robotic helical milling hole system, which could further improve robotic hole-making ability in airplane digital assembly. After analysis on the characteristics of helical milling hole, advantages and limitations of two typical robotic helical milling hole systems were summarized. Then, vector model of helical milling hole movement was built on vector analysis method. Finally, surface roughness calculation formula was deduced according to the movement principle of helical milling hole, then the influence of main technological parameters on surface roughness was analyzed. Analysis shows that theoretical surface roughness of hole becomes poor with the increase of tool speed ratio and revolution radius. Meanwhile, the roughness decreases according to the increase of tool teeth number. The research contributes greatly to the construction of roughness prediction model in helical milling hole.展开更多
Convection heat transfer coefficient and air pressure drop in sinter layer are important factors for the design of sinter cooling craft. Due to the lack of necessary data, the two parameters are studied by experimenta...Convection heat transfer coefficient and air pressure drop in sinter layer are important factors for the design of sinter cooling craft. Due to the lack of necessary data, the two parameters are studied by experimental method. The experimental results show that heat conduction of sinter impacts the measurement of convection heat transfer coefficient. Convection heat transfer increases with the increase of air volumetric flow rate. Sinter layer without small particles(sample I) gives higher convection heat transfer coefficient than that with small particles(sample II). Under the considered conditions, volumetric convection heat transfer coefficient is in the range of 400-1800 W/(m3·°C). Air pressure drop in sinter layer increases with the increase of normal superficial velocity, as well as with the rise of air temperature. Additionally, air pressure drop also depends on sinter particle size distribution. In considered experimental conditions, pressure drop in sinter sample II is 2-3 times that in sinter sample I, which resulted from 17% small scale particles in sinter sample II.展开更多
The mulberry paper handmade dryer uses downdraft gasifier, which is a continuous hot air dryer. The downdraft gasifier uses charcoal or wood chip as fuel to produce the producer gas for a dryer heat source. Two steps ...The mulberry paper handmade dryer uses downdraft gasifier, which is a continuous hot air dryer. The downdraft gasifier uses charcoal or wood chip as fuel to produce the producer gas for a dryer heat source. Two steps operation of a dryer as follows： The frst was to reduce mulberry paper pulp moisture by an air vacuum pump; the second was a continuous hot air drying process. The optimum condition drying, the capacity of dryer, the fuel consumption, the drying constant （k） and economics analysis were investigated. It was found that the first step could be to reduce mulberry paper pulp moisture content about 25% and the suitable condition drying was 80 ~C drying temperature, 0.04 kg/s air mass flow rate and 0.29 m/min chain conveyor speed, respectively. The capacity of this dryer was 20 sheets per hour. The quality of mulberry paper product was very good （based on the standard of mulberry paper community 41/2546） and the fuel consumption rate was 5 kg/h （charcoal）. The drying constant was about 0.532933-0.541367 min~ and the drying constant was a function of drying temperature （T）, air mass flow rate （F） and conveyor speed （10 as equation of k（T, F, V） = 0.567494 ＋ 0.000422T- 1.40588F- 0.000205 V （R2 = 0.9254） and the breakeven point of dryer was 0.79 years.展开更多
The study on options for catalytic cracking of VGO derived from the Kazakhstan-Russian mixed crude was carried out in a small-scale riser FCC unit. The influence of several catalysts and the LCC-A additive for increas...The study on options for catalytic cracking of VGO derived from the Kazakhstan-Russian mixed crude was carried out in a small-scale riser FCC unit. The influence of several catalysts and the LCC-A additive for increasing propylene yield on the distribution and quality of FCC products was analyzed. This article sets forth the possible issues arising from processing the Kazakhstan-Russian mixed crude in FCC unit and the response measures to be adopted.展开更多
基金Project(2012CB214905)supported by the National Basic Research Program of ChinaProject(51074157)supported by the National Natural Science Foundation of China
文摘Flotation column is widely used as the separation equipment for fine mineral due to its high selectivity. However, this device may be unsuitable for the coarse particle flotation and has high handling ability. A two-stage flotation column with dimensions of 2 000 mm×1 000 mm×4 000 mm was designed to enhance the column flotation process. The energy input was modified by adjusting the flow rate and the head of circulating pump. The flotation column was designed with low energy input in the first stage(speed flotation stage) to recover easy-to-float materials quickly, and high energy input in the second stage(recovery stage) to recover difficult-to-float minerals compulsorily. Contrast experiments on the throughput and coarse coal recovery of high ash coal from the Kailuan Mine were conducted using conventional single-stage flotation column and the two-stage flotation column. The results show that the combustible matter recovery of the two-stage flotation column is 5.25% higher than that of the conventional single-stage flotation column. However, the ash contents of clean coal for both columns are similar. Less coarse coals with low ash are obtained using the two-stage flotation column than that using the single-stage column flotation with the same handling ability. The two-stage flotation column process can enhance coal flotation compared with the conventional single-stage column flotation.
文摘With concentrated juice of mulberry as raw material, the influence of type and dosage of dry aid, the inlet air tempera- ture, inlet flow rate, and rotating speed on spray drying was studied. The spray drying processing conditions of mulberry pow- der were optimized by the L9 （3^4） orthogonal test on the basis of single factor experiment. The results showed that optimum technical parameters to produce mulberry powder were： lS-cyclodextrin as dry aids with dosage of 30%, inlet air temperature of 180 ℃, rotating speed of 18 000 r/min and inlet flow rate of 30 mL/min. The mulberry powder under this optimum process conditions had a loose structure and bright color, fruity flavor was rich, the anthocyanin content for 54.67 mg/g, moisture content for 5.6% and sensory scores for 83.
基金Foundation item： Projects（50975141, 51005118） supported by the National Natural Science Foundation of China Projects（20091652018, 2010352005） supported by Aviation Science Fund of China Project（YKJ11-001） supported by Key Program of Nanjing College of Information Technology Institute, China
文摘To avoid the machine problems of excessive axial force, complex process flow and frequent tool changing during robotic drilling holes, a new hole-making technology (i.e., helical milling hole) was introduced for designing a new robotic helical milling hole system, which could further improve robotic hole-making ability in airplane digital assembly. After analysis on the characteristics of helical milling hole, advantages and limitations of two typical robotic helical milling hole systems were summarized. Then, vector model of helical milling hole movement was built on vector analysis method. Finally, surface roughness calculation formula was deduced according to the movement principle of helical milling hole, then the influence of main technological parameters on surface roughness was analyzed. Analysis shows that theoretical surface roughness of hole becomes poor with the increase of tool speed ratio and revolution radius. Meanwhile, the roughness decreases according to the increase of tool teeth number. The research contributes greatly to the construction of roughness prediction model in helical milling hole.
基金Project(51306198)supported by the National Natural Science Foundation of China
文摘Convection heat transfer coefficient and air pressure drop in sinter layer are important factors for the design of sinter cooling craft. Due to the lack of necessary data, the two parameters are studied by experimental method. The experimental results show that heat conduction of sinter impacts the measurement of convection heat transfer coefficient. Convection heat transfer increases with the increase of air volumetric flow rate. Sinter layer without small particles(sample I) gives higher convection heat transfer coefficient than that with small particles(sample II). Under the considered conditions, volumetric convection heat transfer coefficient is in the range of 400-1800 W/(m3·°C). Air pressure drop in sinter layer increases with the increase of normal superficial velocity, as well as with the rise of air temperature. Additionally, air pressure drop also depends on sinter particle size distribution. In considered experimental conditions, pressure drop in sinter sample II is 2-3 times that in sinter sample I, which resulted from 17% small scale particles in sinter sample II.
文摘The mulberry paper handmade dryer uses downdraft gasifier, which is a continuous hot air dryer. The downdraft gasifier uses charcoal or wood chip as fuel to produce the producer gas for a dryer heat source. Two steps operation of a dryer as follows： The frst was to reduce mulberry paper pulp moisture by an air vacuum pump; the second was a continuous hot air drying process. The optimum condition drying, the capacity of dryer, the fuel consumption, the drying constant （k） and economics analysis were investigated. It was found that the first step could be to reduce mulberry paper pulp moisture content about 25% and the suitable condition drying was 80 ~C drying temperature, 0.04 kg/s air mass flow rate and 0.29 m/min chain conveyor speed, respectively. The capacity of this dryer was 20 sheets per hour. The quality of mulberry paper product was very good （based on the standard of mulberry paper community 41/2546） and the fuel consumption rate was 5 kg/h （charcoal）. The drying constant was about 0.532933-0.541367 min~ and the drying constant was a function of drying temperature （T）, air mass flow rate （F） and conveyor speed （10 as equation of k（T, F, V） = 0.567494 ＋ 0.000422T- 1.40588F- 0.000205 V （R2 = 0.9254） and the breakeven point of dryer was 0.79 years.
文摘The study on options for catalytic cracking of VGO derived from the Kazakhstan-Russian mixed crude was carried out in a small-scale riser FCC unit. The influence of several catalysts and the LCC-A additive for increasing propylene yield on the distribution and quality of FCC products was analyzed. This article sets forth the possible issues arising from processing the Kazakhstan-Russian mixed crude in FCC unit and the response measures to be adopted.
