The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and...The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations.A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control.In comparison with the conventional backup and work roll contours configuration,the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls(ASR) and varying contact backup rolls(VCR).A better strip profile and flatness quality,an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.展开更多
AZ61Mg alloy was multi directionally forged(MDFed) during decreasing temperature condition from 643 K to 483 K at a true strain rate of 3×10-3 s-1 up to cumulative strain of∑△ε=4.0 at maximum.A pass strain of...AZ61Mg alloy was multi directionally forged(MDFed) during decreasing temperature condition from 643 K to 483 K at a true strain rate of 3×10-3 s-1 up to cumulative strain of∑△ε=4.0 at maximum.A pass strain of△ε=0.8 was employed.While average grain size decreased gradually with increasing cumulative strain,the evolution of fine-grained structure strongly depended on the MDF temperature.Under the condition where the temperature was higher than the most adequate one,grain coarsening partially took place during MDF.In contrast,at lower temperature,inhomogeneous microstructure composed of the initial coarse and newly appeared fine grains was evolved.After straining over∑△ε=3.2(i.e.,over 4 passes of MDF) ,equiaxed ultrafine grains(UFGs) having average size of about and lower than 1μm were uniformly evolved.While the MDFed alloy to∑△ε=4.0 possessed relatively high hardness of HV 99,and it accepted further about 20%cold rolling almost without cracking.Because of the superior formability of the UFGed AZ61Mg alloy,the hardness was further easily raised to HV 120 by following cold rolling.展开更多
Continuous vorticity panels were used to model general unsteady inviscid, incompressible, two-dimensional flows. The geometry of the airfoil was approximated by series of short straight segments having endpoints that ...Continuous vorticity panels were used to model general unsteady inviscid, incompressible, two-dimensional flows. The geometry of the airfoil was approximated by series of short straight segments having endpoints that lie on the actual surface. A piecewise linear, continuous distribution of vorticity over the airfoil surface was used to generate disturbance flow. The no-penetration condition was imposed at the midpoint of each segment and at discrete times. The wake was simulated by a system of point vortices, which moved at local fluid velocity. At each time step, a new wake panel with uniform vorticity distribution was attached to the trailing edge, and the condition of constant circulation around the airfoil and wake was imposed. A new expression for Kutta condition was developed to study the interference effect between two impulsively started NACA0012 airfoils. The tandem arrangement was found to be the most effective to enhance the lift of the rear airfoil. The interference effect between tidal turbine blades was shown clearly.展开更多
The main objective of this research was to investigate the ability of a Trichoderma sp. （Td22）, inhibitory to Sclerotinia minor Jagger, to grow and survive in mature wood fibre waste （WFW） compost of paper mill or...The main objective of this research was to investigate the ability of a Trichoderma sp. （Td22）, inhibitory to Sclerotinia minor Jagger, to grow and survive in mature wood fibre waste （WFW） compost of paper mill origin following nutrient amendment. The growth and survival of the fungus in the WFW compost was assessed by serial dilution plate count method followed by confirmation of the fungal identity using pectic enzyme analysis as described in Cruickshank and Pitt [1]. It was found in this study that the population densities of TdE2 achieved under non-sterile conditions in the WFW compost following nutrient amendment was approximately in the range of 7.0 lOgl0 CFU/g dw - 8.5 log10 CFU/g dw after 28 days, depending on pre-treatment. The efficacy of this WFW compost-grown TdE2 for protection of lettuce from attack by S. minor was also demonstrated in glasshouse trials. This study indicates that cellulosic paper mill waste compost could provide an abundant low-cost growth medium for the large-scale cultivation of fungal antagonists, improving prospects for cost-competitiveness with chemical treatments.展开更多
基金Project(20040311890) supported by the Science and Technology Development Foundation of University of Science and Technology Beijing
文摘The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations.A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control.In comparison with the conventional backup and work roll contours configuration,the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls(ASR) and varying contact backup rolls(VCR).A better strip profile and flatness quality,an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.
基金support given by the Light Metals Educational Foundation,Japan,and Ministry of Education,Culture,Sports and Technology,Japan,with Grant No.20560647
文摘AZ61Mg alloy was multi directionally forged(MDFed) during decreasing temperature condition from 643 K to 483 K at a true strain rate of 3×10-3 s-1 up to cumulative strain of∑△ε=4.0 at maximum.A pass strain of△ε=0.8 was employed.While average grain size decreased gradually with increasing cumulative strain,the evolution of fine-grained structure strongly depended on the MDF temperature.Under the condition where the temperature was higher than the most adequate one,grain coarsening partially took place during MDF.In contrast,at lower temperature,inhomogeneous microstructure composed of the initial coarse and newly appeared fine grains was evolved.After straining over∑△ε=3.2(i.e.,over 4 passes of MDF) ,equiaxed ultrafine grains(UFGs) having average size of about and lower than 1μm were uniformly evolved.While the MDFed alloy to∑△ε=4.0 possessed relatively high hardness of HV 99,and it accepted further about 20%cold rolling almost without cracking.Because of the superior formability of the UFGed AZ61Mg alloy,the hardness was further easily raised to HV 120 by following cold rolling.
基金Sponsored by National Natural Science Foundation (No. 50279004)the National Hi-Tech. R&D Program of China (No. 2002aa516010)
文摘Continuous vorticity panels were used to model general unsteady inviscid, incompressible, two-dimensional flows. The geometry of the airfoil was approximated by series of short straight segments having endpoints that lie on the actual surface. A piecewise linear, continuous distribution of vorticity over the airfoil surface was used to generate disturbance flow. The no-penetration condition was imposed at the midpoint of each segment and at discrete times. The wake was simulated by a system of point vortices, which moved at local fluid velocity. At each time step, a new wake panel with uniform vorticity distribution was attached to the trailing edge, and the condition of constant circulation around the airfoil and wake was imposed. A new expression for Kutta condition was developed to study the interference effect between two impulsively started NACA0012 airfoils. The tandem arrangement was found to be the most effective to enhance the lift of the rear airfoil. The interference effect between tidal turbine blades was shown clearly.
文摘The main objective of this research was to investigate the ability of a Trichoderma sp. （Td22）, inhibitory to Sclerotinia minor Jagger, to grow and survive in mature wood fibre waste （WFW） compost of paper mill origin following nutrient amendment. The growth and survival of the fungus in the WFW compost was assessed by serial dilution plate count method followed by confirmation of the fungal identity using pectic enzyme analysis as described in Cruickshank and Pitt [1]. It was found in this study that the population densities of TdE2 achieved under non-sterile conditions in the WFW compost following nutrient amendment was approximately in the range of 7.0 lOgl0 CFU/g dw - 8.5 log10 CFU/g dw after 28 days, depending on pre-treatment. The efficacy of this WFW compost-grown TdE2 for protection of lettuce from attack by S. minor was also demonstrated in glasshouse trials. This study indicates that cellulosic paper mill waste compost could provide an abundant low-cost growth medium for the large-scale cultivation of fungal antagonists, improving prospects for cost-competitiveness with chemical treatments.
