钢纤混凝土裂纹尖端应变场的实验研究

本文应用散斑干涉技术对四组含纤量分别为０，０．５％，１％，１．５％的钢纤混凝土三点弯曲裂纹试件的裂纹尖端位移场进行了测试，并换算为应变场。对钢纤混凝土裂纹开裂的基理进行了探讨；验证了最大拉应变准则；并测定了断裂韧度Ｊ１ｃ。

Electroplastic effect in AZ31B magnesium alloy sheet through uniaxial tensile tests

The electroplastic effect in AZ31B magnesium alloy sheet was investigated through uniaxial tensile tests. In order to show the athermal effect of the electrical pulses, two types of uniaxial tensile tests at the same testing temperature were carried out： uniaxial tension in environmental cabinet and uniaxial tension with electrical pulses. In addition, the distribution of temperature field in the cross-section area during uniaxial tension with electrical pulses was simulated. The results show that the distribution of temperature field along the cross-section area is homogeneous. By comparing the true stress？true strain curves of AZ31B alloy under uniaxial tensile tests, the athermal effect with electrical pulses was confirmed. The microstructure evolution after the uniaxial tension was studied by optical microscopy. The results indicate that the electrical pulses induced dynamic recrystallization plays an important role in the decrease of flow stress. Finally, a flow stress model of AZ31B sheet taking the influence of electroplastic effect into account was proposed and validated. The results demonstrate that the calculated data fit the experimental data well.

Temperature and stress fields in electron beam welded Ti-15-3 alloy to 304 stainless steel joint with copper interlayer sheet

Electron beam welding of Ti-15-3 alloy to 304 stainless steel （STS） using a copper filler metal was carried out. The temperature fields and stress distributions in the Ti/Fe and Ti/Cu/Fe joint during the welding process were numerically simulated and experimentally measured. The results show that the rotated parabola body heat source is fit for the simulation of the electron beam welding. The temperature distribution is asymmetric along the weld center and the temperature in the titanium alloy plate is higher than that in the 304 STS plate. The thermal stress also appears to be in asymmetric distribution. The residual tensile stress mainly exists in the weld at the 304 STS side. The copper filler metal decreases the peak temperature and temperature grade in the joint as well as the residual stress. The longitudinal and lateral residual tensile strengths reduce by 66 MPa and 31 MPa, respectively. From the temperature and residual stress, it is concluded that copper is a good filler metal candidate for the electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel.

Residual elastic stress strain field and geometrically necessary dislocation density distribution around nano-indentation in TA15 titanium alloy

Nanoindentation and high resolution electron backscatter diffraction（EBSD） were combined to examine the elastic modulus and hardness of α and β phases,anisotropy in residual elastic stress strain fields and distributions of geometrically necessary dislocation（GND） density around the indentations within TA15 titanium alloy.The nano-indention tests were conducted on α and β phases,respectively.The residual stress strain fields surrounding the indentation were calculated through crosscorrelation method from recorded patterns.The GND density distribution around the indentation was calculated based on the strain gradient theories to reveal the micro-mechanism of plastic deformation.The results indicate that the elastic modulus and hardness for α p hase are 129.05 GPas and 6.44 GPa,while for β phase,their values are 109.80 GPa and 4.29 GPa,respectively.The residual Mises stress distribution around the indentation is relatively heterogeneous and significantly influenced by neighboring soft β phase.The region with low residual stress around the indentation is accompanied with markedly high a type and prismatic-GND density.

Oxide Thickness Effects on n-MOSFETs Under On-State Hot-Carrier Stress

Hot carrier induced (HCI) degradation of surface channel n MOSFETs with different oxide thicknesses is investigated under maximum substrate current condition.Results show that the key parameters m and n of Hu's lifetime prediction model have a close relationship with oxide thickness.Furthermore,a linear relationship is found between m and n .Based on this result,the lifetime prediction model can be expended to the device with thinner oxides.

Finite element analysis of pressure on 2024 aluminum alloy created during restricting expansion-deformation heat-treatment

Metals heat-treated under high pressure can exhibit different properties. The heat-induced pressure on 2024 aluminum alloy during restricting expansion-deformation heat-treatment was calculated by using the ABAQUS finite element software, and the effects of the mould material properties, such as coefficient of thermal expansion （CTE）, elastic modulus and yield strength, on the pressure were discussed. The simulated results show that the relatively uniform heat-induced pressure, approximately 503 MPa at 500 ℃, appears on 2024 alloy when 42CrMo steel is as the mould material. The heat-induced pressure increases with decreasing the CTE and the increases of elastic modulus and yield strength of the mould material. The influences of the CTE and elastic modulus on the heat-induced pressure are more notable.

DIMENSIONLESS ANALYSIS AND LOCATION OF ELECTRIC FIELD INDUCED BY MAGNETIC COIL

A model of magnetic stimulation is presented for analysis of the spatial distributions of the electric field induced by magnetic coils.Dimensionless analysis is introduced and makes the factors influencing the magnitude of electric field into two parts:c (represents the stimulation conditions),and E 0 (reflects the geometry of coil).By 3 D simulation of the induced electric field of two kinds of coils,the effect of magnetic stimulation can be demonstrated and the factors influencing stimulating focality and depth are identified.The principles for determining the electric field magnitude,focality and magnetic stimulation depth when designing a reasonable coil and stimulator and achieving ideal stimulating effect are discussed.

Investigation on the stress field characteristic of top coal at FMTC faces under the influence of caving thickness

In the background of the technology condition and the geological condition of the 1151（3） fully mechanized top-coal caving face （FMTC face）, and by means of taking nonlinear 3D numerical simulation, the stress redistribution rules of top coal with different thick coal seam were obtained by investigation on the numerical simulation of the redistributions of the stress with different coal seam＇s thickness. The research showes that there exists a certain difference on the stress distributions of the top coal at face, the maximum principal stress is located near to the tailentry＇s corner. The vertical stress＇s peak of the top coal decreases and the distance ahead of face position increases as the once mining thickness of the coal seam increases. At the same coal seam, the vertical stresses＇ peak of top coal gradually decreases from the top to the bottom, the peak＇s position is basically the same and its changes are gradually obvious with the thickness of coal seam increas- ing. The vertical stress of top coal places in a low stress state at a certain range ahead of face and over the face, which reveals the essence that the support loads are generally low under the condition of FMTC. The study supplies the theoretical foundation for the support design and selection, the theory of top coal＇s fragmentation, the movement rules of top coal and improving the recovery of top coal.

Tribological properties and thermal-stress analysis of C/C-SiC composites during braking

The tribological properties and thermal-stress behaviors of C/C-SiC composites during braking were investigated aiming to simulate braking tests of high-speed trains. The temperature and structural fields of C/C-SiC composites during braking were fully coupled and simulated with ANSYS software. The results of tribological tests indicated that the C/C-SiC composites showed excellent static friction coefficient (0.68) and dynamic friction coefficient (average value of 0.36). The highest temperature on friction surface was 445℃. The simulated temperature field showed that the highest temperature which appeared on the friction surface during braking was about 463℃. Analysis regarding thermal-stress field showed that the highest thermal-stress on friction surface was 11.5 MPa. The temperature and thermal-stress distributions on friction surface during braking showed the same tendency.

Temperature field evolution and heat transfer during continual local induction cladding

The evolution of temperature field of the continual motion induction cladding and the depth of heat affected zone are studied in this study.A three-dimensional finite element model for the point type continual induction cladding is established to investigate temperature distributions of fixed and motion induction cladding modes.The novel inductor is designed for cladding of curved surfaces.The modeling reliability is verified by the temperature measurements.The influence of process parameters on the maximum temperature and the generation and transfer of heat are studied.Quantitative calculation is performed to its melting rate to verify the temperature distribution and microstructures.The results show that a good metallurgical bond can be formed between the cladding layer and substrate.The melting rate gradually falls from the top of the cladding layer to the substrate,and the grain size in the substrate gradually rises.The heat affected zone is relatively small compared to integral heating.

Finite element analysis of temperature and stress fields during selective laser melting process of Al−Mg−Sc−Zr alloy

A 3D finite element model was established to investigate the temperature and stress fields during the selective laser melting process of Al−Mg−Sc−Zr alloy.By considering the powder−solid transformation,temperaturedependent thermal properties,latent heat of phase transformations and molten pool convection,the effects of laser power,point distance and hatch spacing on the temperature distribution,molten pool dimensions and residual stress distribution were investigated.Then,the effects of laser power,point distance and hatch spacing on the microstructure,density and hardness of the alloy were studied by the experimental method.The results show that the molten pool size gradually increases as the laser power increases and the point distance and hatch spacing decrease.The residual stress mainly concentrates in the middle of the first scanning track and the beginning and end of each scanning track.Experimental results demonstrate the accuracy of the model.The density of the samples tends to increase and then decrease with increasing laser power and decreasing point distance and hatch spacing.The optimum process parameters are laser power of 325−375 W,point distance of 80−100μm and hatch spacing of 80μm.

Effects of Surface Etch Hole Fault on the Velocity Field in Microchannel Reactors

Microchannel reactors are commonly used in micro-chemical technology. The performance of microreactors is greatly affected by the velocity field in the microchannel. The flow field is disturbed by the cylindrical etch holes caused by air dust on the microchannel surface during its processing procedure. In this approach, a two-dimensional computational fluid dynamics （CFD） model is put forward to study the effect of etch holes on flow field. The influenced area of single or two concave etch holes is studied for the case of laminar flow. The hole diameter, the Reynolds number and the distance between the center of holes are found to have influences on the flow field. Numerical results indicate that the effects of etch hole on the flow field should be evaluated and the way of choosing the economic class of cleanroom for microreactor manufacture is presented.

Analysis of the Effects of Slope Geometry on the Dynamic Response of a Near-field Mountain from the Wenchuan Earthquake

Fourier spectra and acceleration response spectra of near-field acceleration records of the 2008 Wenchuan Earthquake have been calculated.Relative fundamental frequencies(or predominant periods) were characterized.Then,the natural frequencies of a range of slopes with different geometric characteristics,such as height,slope ratio,and pattern,were analyzed.The seismic responses of the slopes were compared,and the variability of seismic response with the above geometric elements was found.Results show that if slope height increases,and provided that other conditions are unchanged,the natural frequency of the first mode of a doublesurface slope will change as a power law.However,natural frequencies will diminish(based on a parabolic function) as the slope angle becomes large.Both the surface pattern and the number of surfaces on a slope can have a great impact on the seismic response of the slope.Moreover,within a certain range of slope heights or angles,either height or angle will also greatly influence the variability of the seismic response.The results of this research will be helpful to understanding seismic dynamic response features and explaining the ways that slope stability can be affected by earthquakes.

Residual stress and welding distortion of Al/steel butt joint by arc-assisted laser welding-brazing

The thermo-elastic.plastic finite element method(FEM)is used to simulate the thermo-mechanical behavior of Al/steel tungsten inert gas(TIG)arc-assisted laser welding-brazing(A-LWB)butt joint.The influence of material nonlinearity,geometrical nonlinearity and work hardening on the welding process is studied,and the differences in the welding temperature field,residual stress and welding distortion by A-LWB and by single laser welding-brazing(SLWB)are analyzed.The results show that the thermal cycle,residual stress distribution and welding distortion by the numerical simulation are in good agreement with the measured data by experiments,which verifies the effectiveness of FEM.Compared with the SLWB,A-LWB can make the high-temperature distribution zone of weld in width direction wider,decrease the transverse tensile stress in the weld and reduce the distribution range of longitudinal tensile stress.And the welding deformation also decreases to some extent.

Effect of Magnetic Field on the Extraction Process of Acetone-Water-Trichloroethane System

In order to investigate the effect of magnetic field on the liquid-liquid extraction, the extraction in the acetone-water-trichloroethane system was studied under magnetic field with different magnetic induction intensity.The results showed that the effect of magnetic field was positive in the extraction process, and the partition coeffi-cient and the yield of acetone increased-with the increasing magnetic induction intensity by 5.16%-8.35% and 1.85%-5.70% respectively. The effect of magnetic field on the extraction was intensified when the temperature became, higher. The experimental data of the partition coefficient of acetone were correlated by the method of least square in terms of a power-law correlation.

Numerical simulation of dust distribution at a fully mechanized face under the isolation effect of an air curtain

At a fully mechanized working face of a coal mine as prototype,we investigated,by simulation,the flow field and dust distribution during the process of its isolation by a curtain of air,using the CFD software, Fluent.The results show that the air curtain installed on the shearer can effectively prevent the dust （especially the respirable dust）from diffusing into the work area of the operator,reducing the dust concentration on the side of the operator and greatly improving his working environment.The field application of the air curtain shows that the dust-isolation effect of an air curtain is quite noticeable.The isolation efficiency for respiratory dust is over 70%and,as well,it has good dust-isolation effect for nonrespiratory dust.The air curtain is a useful way to resolve the problem of dust-isolation at a fully mechanized working face.It has a practical background elsewhere with more extensive applications.

Study on Dragline-Bulldozer Operation with Variations in Coal Seam Thickness

The dragline is one of the most promising surface mining machines in China. This paper studies the interac-tion between the working bench advancing speed and the stripping volume with variation in coal seam thickness. Ad-justing the bulldozing volume (depth) and/or changing the dragline bench height are proposed as means to ensure a smooth and economical mining operation. When the coal seam is getting thicker it is recommended to reduce the bull-dozing volume (depth) for a higher dragline efficiency. When the coal seam is getting thinner it is recommended to in-crease the bulldozing volume (depth) to ensure the dragline can work at the proper bench height.

Enzymatic Hydrolysis of Cellulose with Different Crystallinities Studied by Means of SEC-MALLS

The reactions of exo-cellulase （cellobiohydrolase, CBH） and endo-cellulase （endoglucanase, EG） were investigated by analyzing the insoluble residues of microcrystalline cellulose （MCC） and filter paper cellulose （FPC） during enzymatic hydrolysis. Molecular parameters including molecular weight and its distribution, degree of polymerization, and radii of gyration were measured by size exclusion chromatography coupled with multi-angle laser light scattering. No significant change in MCC chains was found during the whole reaction period, indicating that CBH digestion follows a layer-by-layer solubilization manner. This reaction mode might be the major reason for slow enzymatic hydrolysis of cellulose. On the other hand, the degree of polymerization of FPC chains decreases rapidly in the initial reaction, indicating that EG digestion follows a random scission manner, which may create new ends for CBH easily. The slopes of the conformation plots for MCC and FPC increase gradually, indicating stronger chain stiffness of cellulose during hvdrolvsis

CORRECTION OF ASYMMETRIC STRENGTHENING OF QUIKSCAT WIND FIELD AND ASSIMILATION APPLICATION IN TYPHOON SIMULATION

As an approach to the technological problem that the wind data of QuikSCAT scatterometer cannot accurately describe the zone of typhoon-level strong wind speed, some objective factors such as the typhoon moving speed, direction and friction are introduced in this study to construct the asymmetric strengthening of the QuikSCAT wind field. Then by adopting a technology of four-dimensional data assimilation, an experiment that includes both the assimilation and forecasting phases is designed to simulate Typhoon Rananim numerically. The results show that with model constraints and adjustment, this technology can incorporate the QuikSCAT wind data to the entire column of the model atmosphere, improve greatly the simulating effects of the whole-column wind, pressure field and the track as well as the simulated typhoon intensity covered by the forecast phase, and work positively for the forecasting of landfall locations.

Microscopic phase-field modeling of atomic anti-site behaviors in precipitation progress of Ni_3(AlFe)

The effects of temperature on atomic anti-site behaviors in L12-Ni3(AlFe) phases were studied using microscopic phase-field dynamic model in precipitation progress of Ni75Al20Fe5 alloy.The results show that with the increase of temperature,the formation of NiAl and AlNi anti-sites is much easier in Ni3(AlFe),and Ni and Al anti-site atoms show clearly stronger temperature-dependent than Fe anti-site atoms.The evolution progress of anti-site atoms is completed at the initial growth stage of L12-Ni3(AlFe) phases.The site occupation probabilities of Ni atoms on the sublattice A(NiNi,face centers sites of FCC),and Al and Fe atoms on the sublattice B(AlAl and FeAl,corners sites of FCC) all present the degressive tendency with the temperature increasing.Fe atoms mainly prefer to occupy the Al sublattice at the whole temperature range.