延时方治疗早泄临床观察

目的:观察延时方治疗原发性早泄的临床疗效。方法:58例随机分为两组,对照组24例采用达泊西汀,试验组34例用延时方治疗,均治疗8周。结果:治疗后试验组和对照组阴道内射精潜伏期均较本组治疗前明显延长,CIPE-5积分增加,治疗前后比较有差异有统计学意义(P<0.05);试验组较对照组阴道内射精潜伏期及CIPE-5积分改善明显(P<0.05)。结论:延时方可明显增加阴道内射精潜伏期。

Stochastic Analysis of Interconnect Delay in the Presence of Process Variations

Process variations can reduce the accuracy in estimation of interconnect performance. This work presents a process variation based stochastic model and proposes an effective analytical method to estimate interconnect delay. The technique decouples the stochastic interconnect segments by an improved decoupling method. Combined with a polynomial chaos expression （PCE）, this paper applies the stochastic Galerkin method （SGM） to analyze the system response. A finite representation of interconnect delay is then obtained with the complex approximation method and the bisection method. Results from the analysis match well with those from SPICE. Moreover, the method shows good computational efficiency, as the running time is much less than the SPICE simulation＇s.

基于源节点发包速度的大型无线网络实时服务性能分析

由于无线多跳通信在大型无线网络中应用广泛,因而对网络实时服务质量的研究变得非常重要。实时事件检测或报告的无线传感器网络、可视化传感器网络实时事件检测存在一些缺陷,如实时服务质量性能指标的端到端延时和吞吐量会随无线跳数增加而快速降低。以源节点发包速度为新的分析角度进行网络实时服务质量性能计算,将认知网络和无线多跳网络相结合,实现数据包在每一跳都能转发。在转发过程中引入源节点发包速度计算吞吐量、端到端延时和延时方差。分析和仿真结果表明,源节点发包速度的提高会在更短时间内提高网络吞吐量并达到最大吞吐量且最大吞吐量会有所增大,但是越高的源节点发包速度会在发包时间过长的情况下更快速地造成严重的网络拥塞,增大网络端到端平均时延和时延方差,增大网络能源消耗。

A packet loss avoidance handoff scheme

The basic mobile IP protocol is simple but only suitable for wide area and low speed networks. In this paper, we propose a novel micro-mobile IP handoff scheme, that is the packet loss avoidance handoff scheme. By using an additional cache at the base station and distinguishing packets with packet IDs, the proposed scheme minimizes the number of lost packets during handoff. Network architecture and detailed handoff procedures are given. We also analyze the cache size at the base station, the associated network load with the handoff procedure, and the handoff delay. The scheme is investigated by computer simulations. Simulation results show that the proposed scheme is suitable for environments with fast mobility and frequent handoff.

MDL-based root-mean-squared delay spread estimation for MIMO OFDM systems

This paper studied the application of minimum description length (MDL) criterion for estimating root-mean-squared (RMS) delay spread (RDS) for MIMO OFDM systems. The analytic relationship between the powers and the correlation matrix of multipath components established the feasibility of the application of the MDL criterion to RDS estimation. The estimator presented both the estimate of instantaneous RDS and the estimates of noise variance, channel power and SNR of current channel with low computational complexity. Given the powers of the estimated multipath components, the MDL criterion was adopted to acquire the number of paths and the time delays of each path of current channel without making eigendecomposition of the correlation matrix normally required by MDL criterion, following which the noise variance and the power of each path can be estimated. The power delay profile (PDP) and RDS of the current channel were achieved. Simulation results showed that the proposed estimator was insensitive to variance of SNR and robust against frequency-selectivity.

IMC-PID tuning method based on sensitivity specification for process with time-delay

To overcome the deficiencies addressed in the conventional PID control and improve the dynamic performance and robustness of the system, a simple design and parameters tuning approach of internal model control-PID （IMC-PID） controller was proposed for the first order plus time-delay （FOPTD） process and the second order plus time-delay （SOPTD） process. By approximating the time-delay term of the process model with the first-order Taylor series, the expressions for IMC-PID controller parameters were derived, and they had only one adjustable parameter 2 which was directly related to the dynamic performance and robustness of the system. Moreover, an analytical approach of selecting 2 was given based on the maximum sensitivity Ms. Then, the robust tuning of the system could be achieved according to the value of Ms. In addition, the proposed method could be extended to the integrator plus time-delay （IPTD） process and the first order delay integrating （FODI） process. Simulation studies were carried out on various processes with time-delay, and the results show that the proposed method could provide a better dynamic performance of both the set-point tracking and disturbance rejection and robustness against parameters perturbation.

Joint Optimization on Energy and Delay for Target Tracking in Internet of Things

Network and communications models are built for target tracking and pursuing in the Internet of Things (IoT).According to these models,two tracking schemes which jointly optimize the pursuing energy and delay are proposed.The merits of these schemes are that they can enhance energy efficiency of both the pursuing route and communication in the network.Moreover,experimental results are provided to demonstrate the benefits of the proposed schemes which will be used as optimization schemes for the IoT tracking service.

A Location-Based Content Search Approach in Hybrid Delay Tolerant Networks

In Delay Tolerant Networks （DTNs）, the offiine users can, through the encountering nodes, use the specific peer-to-peer message routing approach to deliver messages to the destination. Thus, it solves the problem that users have the demands to deliver messages while they are temporarily not able to connect to the Internet. Therefore, by the characteristics of DTNs, people who are not online can still query some location based information, with the help of users using the same service in the nearby area. In this paper, we proposed a location-based content search approach. Based on the concept of three-tier area and hybrid node types, we presented four strategies to solve the query problem, namely, Data Replication, Query Replication, Data Reply, and Data Synchronization strategies. Especially we proposed a Message Queue Selection algorithm for message transferring. The priority concept is set associated with every message such that the most ＂important＂ one could be sent first. In this way, it can increase the query success ratio and reduce the query delay time. Finally, we evaluated our approach, and compared with other routing schemes. The simulation results showed that our proposed approach had better query efficiency and shorter delay.

Influence of Dark Energy on Gravitational Time Delay

We investigate the gravitational time delay of light in the Schwarzschild black hole space-time surroundedby quintessence.With the analysis and numerical methods,we find that the gravitational time delay of light in theSchwarzschild black hole space-time surrounded by quintessence increases when the normalization factor c increases,andthat the gravitational time delay also decreases when the quintessential state parameter ω_q increases.

Operation Modes and Control Schemes for Internet-Based Teleoperation System with Time Delay

Teleoperation system plays an important role in executing task under hazard environment. As the computer networks such as the Internet are being used as the communication channel of teleoperation system, varying time delay causes the overall system unstable and reduces the performance of transparency. This paper proposed twelve operation modes with different control schemes for teleoperation on the Internet with time delay. And an optimal operation mode with control scheme was specified for teleoperation with time delay, based on the tradeoff between passivity and transparency properties. It experimentally confirmed the validity of the proposed optimal mode and control scheme by using a simple one DOF master-slave manipulator system.

Matrix-Geometric Method Based Unified Delay Analysis for Wireless Relay Networks

A lot of work has been focused on desig-ning and analyzing various cooperative diversity pro-tocols for wireless relay networks. To provide a uni-fied queuing analytic framework, we fonmlate an em-bedded Markov chain, which rams out to be a Quasi-Birth-and-Death （QBD） process. Using the Matrix-Ce-ometric method, we can analyze the average delay in a unified way. Theoretical analysis is validated by simu-lation results. We show that the delay performances of Amplify-and-Forward or Decode-and-Forwaxd （AF/ DF） and incremental AF/DF schemes can be analyzed in the unified way. Thus, we can always choose the best cooperative diversity scheme in different scenari-os for delay minimization.

Travelling Solitary Wave Solutions for Generalized Time-delayed Burgers-Fisher Equation

In this paper,travelling wave solutions for the generalized time-delayed Burgers-Fisher equation arestudied.By using the first-integral method,which is based on the ring theory of commutative algebra,we obtain aclass of travelling solitary wave solutions for the generalized time-delayed Burgers-Fisher equation.A minor error in theprevious article is clarified.

Nonlinear characteristics and functional analysis of masseter electromyography

The C-C method was adopted to analyze the nonlinear characteristics of masseter electromyography （EMG） signals and the chaotic degree by the largest Lyapunov exponent （LLE） of different genders and sides. First, the embedding dimension and the delay time were obtained through this method, then the phase space was reconstructed to resume the chaotie attractor and determine the LLE. The result shows that the trajectory of attractor is denser than Chen＇s attractor, and the LLE is positive, which means that not only the signal has the character of chaos, but also the chaotic degree of masseter EMG is relatively high. According to the value of the LLE, the chaotic degree of men＇s masseter EMG is higher than that of women＇s; when the dentition is normal, the chaotic degree of two sides is almost the same. Then, a conclusion can be deduced that if the LLE of both sides are in great difference, the unilateral mastication is likely to exist, which means that the nonlinear characteristics of masseter EMG can be applied to predict the unilateral mastication.

Workability Tests on Fresh Concrete Formulated with Eco-friendly Admixture

Extra-cellular compounds, secreted by microorganisms into their surroundings, can be integrated in concrete composition as admixtures. These substances are important in biofilm formation and some of them can be used as corrosion inhibitor of concrete reinforcement. This paper deals with products made with biological surface active compounds/agents allowing the development of more eco-friendly concrete. The influence of this environmentally friendly bio admixture on setting time, workability, bending and compressive strengths of various mortar based materials made of CEM I, CEM III and CEM V was studied. Mechanical tests were carried out to highlight the influence of admixture in workability and hardening of samples containing the biological product with ratio in the range of 0-2.5%. It was demonstrated that the presence of the new bio-compound admixture in mortar decreases their compressive strength after 28 days of standard curing, in spite of remaining higher than standard minimal strength. Furthermore, Vicat needle experiments have shown a tendency of this admixture to decrease the setting time. A discussion was finally proposed in order to correlate the setting times and the decrease of the mortar compressive strength, corresponding in fact to a hardening delay. This setting time delay could be linked to a delay of the admixtured mortar to increase its resistance. The slump results highlight the action of bio-admixture as a plasticizer on mortars because it increases their workability for a same water-cement ratio. This effect seems variable according to the added amount.

A Shear-wave Splitting Study of the Yingjiang M_S6.1 Earthquake Sequence Occurring on May 30,2014

Earthquakes of M_S5. 6 and M_S6.1 occurred in Yingjiang,Yunnan on May 24 and May 30,2014 respectively. In this paper,we use the waveform data recorded by mobile seismic stations( KAC) which were set up in the source area after the Yingjiang MS5. 6earthquake on May 24,2014 to study the shear-wave splitting characteristics of Yingjiang M_S6.1 earthquake sequence with the SAM method. The result shows that predominant polarization of fast shear-waves before the M_S6.1 earthquake is consistent with the direction of regional principal compressive stress,and predominant polarization of fast shear-waves before the M_S6.1 earthquake show better consistency and smaller dispersion compared to after the M_S6.1 earthquake,and there may be a deflection for the fast shearwaves predominant polarization between the M_S6.1 earthquake sequence and foreshock sequence. We found that the time-delays generally exhibited a lower level before the M_S6.1earthquake and a relatively higher value after the M_S6.1 earthquake.

ULTIMATE STABILITY OF A TYPE OF CHARACTERISTIC EQUATION WITH DELAY DEPENDENT PARAMETERS

Delay differential systems are widely used in many different fields, It is important to determine the local stability of their equilibria, For systems with＇ delay dependent parameters, the stability analysis of equilibria is complicated and difficult In this paper, we shall investigate the ultimate stability of a type of characteristic equation with delay dependent parameters. Our results show that the characteristic equation with delay dependent parameters may be one of ultimately stable, ultimately unstable, and alternate between stable and unstable. Applying our results, the ultimate stability can be often decided directly and need not appeal to mathematic software. Two examples are given in this paper,

Singularly Perturbed Differential-Difference Reaction Diffusion Equations with Time Delay

A class of differential-difference reaction diffusion equations with a small time delay is considered.Under suitable conditions and by using the method of the stretched variable,the formal asymptotic solution is constructed.And then,by using the theory of differential inequalities the uniformly validity of solution is proved.

Variations of shear wave splitting in the 2013 Lushan Ms7.0 earthquake region

In this paper, variations of shear wave splitting in the 2013 Lushan Ms7.0 earthquake sequence were studied. By analyzing shear wave particle motion of local events in the shear wave window, the fast polarization directions and the delay time between fast and slow shear waves were derived from seismic recordings at eight stations on the southern segment of the Longmenshan fault zone. In the study region, the fast polarization directions show partition characteristics from south to north. And the systematic changes of the time delays between two split shear waves were also observed. As for spatial distribution, the NE fast polarization directions are consistent with the Longmenshan fault strike in the south of focal region, whereas the NW fast direction is parallel to the direction of regional principal compressive stress in the north of focal region. Stations BAX and TQU are respectively located on the Central and Front-range faults, and because of the direct influence of these faults, the fast directions at both stations show particularity. In time domain, after the main shock, the delay times at stations increased rapidly, and decreased after a period of time. Shear-wave splitting was caused mostly by stress-aligned microcracks in rock below the stations. The results demonstrate changes of local stress field during the main shock and the aftershocks. The stress on the Lushan Ms7.0 earthquake region increased after the main shock, with the stress release caused by the aftershocks and the stress reduced in the late stage.

Upper mantle anisotropy in the Ordos Block and its margins

Based on the polarization analysis of teleseismic data,SKS (SKKS) fast-wave directions and delay times between fast and slow shear waves were determined for each of the 111 seismic stations from both permanent and temporary broadband seismograph networks deployed in the Ordos Block and its margins.Both the Silver and Chan and stacking analysis methods were used.In this way,an image of upper mantle anisotropy in the Ordos Block and its margins was acquired.In the western and northern margins of the Ordos Block,the fast-wave directions are consistently NW-SE.The fast-wave directions are mainly NWW-SEE and EW in the southern margin of the Ordos Block.In the eastern margin of the Ordos Block,the fast-wave directions are generally EW,although some run NEE-SWW or NWW-SEE.In the Ordos Block,the fast-wave directions trend near N-S in the north,but switch to near EW in the south.The delay time between fast and slow waves falls into the interval 0.48-1.50 s,and the average delay time at the stations in the Ordos Block is less than that in its margins.We suggest that the anisotropy of the stable Ordos Block is mainly caused by "fossil" anisotropy frozen in the ancient North China Craton.The NE-trending push of the northeastern margin of the Tibetan Plateau has caused NW-SE-trending lithospheric extension in the western and northern margins of the Ordos Block,and made the upper mantle flow southeastwards.This in turn has resulted in the alignment of the upper mantle peridotite lattice with the direction of material deformation.In the southern margin of the Ordos Block,the collision between the North China and Yangtze blocks resulted in the fast-wave direction running parallel to the collision boundary and the Qinling Orogen.Combining this with the APM and velocity structure of the Qinling Orogen,we propose that eastward-directed asthenospheric-mantle channel flow may have occurred beneath the Qinling Orogen.In the eastern margin of the Ordos Block,the complex anisotropic characteristics of the Fenhe Graben and Taihang Orogen may be caused by the interaction of western Pacific Plate subduction,regional extensional tectonics,and the orogeny.For station YCI,the apparent splitting parameters (the fast-wave directions range from 45° to 106° and the delay times range from 0.6 to 1.5 s) exhibit systematic variations as a function of incoming polarization with a periodicity of π/2.This variation can be best explained by a two-layer anisotropic model (φlower=132°,δtlower=0.8 s,φupper=83°,δtupper=0.5 s).The upper layer anisotropy beneath station YCI can again be attributed to "fossil" anisotropy frozen in the ancient North China Craton.The lower layer anisotropy is affected by the tectonic activity of the western Ordos Block.The NW-SE trending extension caused by the NE trending push of the northeastern margin of the Tibetan Plateau affected the deformation of the lower anisotropic layer beneath station YCI.By comparing the fast-wave directions with GPS velocity directions,we see that the crust and upper mantle possibly have vertically coherent deformation in the margins of the Ordos Block,whereas the internal deformation characteristics of the Ordos Block are complex and require further study.

Milling stability analysis using the spectral method

This paper focuses on the development of an efficient semi-analytical solution of chatter stability in milling based on the spectral method for integral equations. The time-periodic dynamics of the milling process taking the regenerative effect into account is formulated as a delayed differential equation with time-periodic coefficients, and then reformulated as a form of integral equation. On the basis of one tooth period being divided into a series of subintervals, the barycentric Lagrange interpolation polynomials are employed to approximate the state term and the delay term in the integral equation, respectively, while the Gaussian quadrature method is utilized to approximate the integral tenn. Thereafter, the Floquet transition matrix within the tooth period is constructed to predict the chatter stability according to Floquet theory. Experimental-validated one-degree-of-freedom and two-degree-of-freedom milling examples are used to verify the proposed algorithm, and compared with existing algorithms, it has the advantages of high rate of convergence and high computational efficiency.