开采矿压对底板的损伤破坏及其对突水的诱发作用

在介绍采场前后方支承压力分布规律的基础上 ,对采动矿压对煤层底板岩体的损伤破坏作用和破坏深度进行了详细分析 ,提出了开采矿压诱发突水的 4种条件和诱发突水的时 -空规律与特征。

近距离煤层开采矿压显现规律研究

在经济快速发展的今天,煤炭已成为不可替代的基础性资源之一。由于煤层开采过程中会出现显著改变矿压,使得安全风险问题较为突出。本文结合实际情况,分析了在近距离煤层开采时开采矿压的表现形式及特征,进而总结出开采矿压的显现规律。

FEM analyses of stress and deformation of a flexible inner pressure bolt

The flexible inner pressure bolt is a new kind and new structural bolt (anchor rod). A number of structural improvements and performance test have been carried out. The bolt has superior compatibility to the soft crag and the large distortion tunnel with its flexibility. In order to study its stress, deformation and interaction mechanism thoroughly, a number of large distortion calcula- tions and analyses have been carried out on the bolt by FEM (finite element method), especially with the ANSYS software, based on the updated Lagrangian law. The results show that the maximum stress of the inner wall of the bolt is consistent with an elastic analytic solution. The maximum stress on the body occurs in the vicinity of the enhancement material. The link enhancement of the body seems to be quite essential. The experimental results indicate that the maximum injection pressure in the bolt is 2.5 MPa without link enhancement and 8.3 MPa with the enhancement. This link enhancement effect is highly significant. These results provide some basis for the design, application and anchoring stress analysis of the bolt.

Strata behavior investigation for high-intensity mining in the water-rich coal seam

This paper describes a specific case of mining in a water-rich coal seam in western China. Water inrushes,roof caving and other disasters induced by intensive mining operation could pose great threats to the safety of coal mines. The strata behavior during the high-intensity extraction in the water-rich coal seam is analyzed by employing the numerical simulation method and in situ monitoring. The results show that about 10 m ahead of the workface, the front abutment pressure peaks is at 34.13 MPa, while the peak of the side abutment pressure is located about 8 m away from the gateway with the value of 12.41 MPa; the height of the fracture zone, the first weighting step and the cycle weighting step are calculated to be 45,50 and 20.8 m, respectively; pressure distribution in the workface is characterized by that the vertical pressure in the center occurs earlier and is stronger than those on both ends. Then, the results above are verified by in situ measurement, which may provide a basis for safe mining under similar conditions.

Study on gob-side entry retaining technique with roadside packing in longwall top-coal caving technology

Pointed out some technical difficulties of gob-side entry retaining with roadside packing in longwall top-coal caving technology (LTCT), and analyzed the function mecha-nism of roadside filling body. Theory analysis shows the mechanical properties of high water material fit for the feature of deformation of gob-side entry retaining in LTCT, and gob-side entry retaining in LTCT face is one of effective ways to increase the recovery ra-tio of mining district.

FUZZY MATHEMATICAL EVALUATION FOR MASONRY STRUCTURE BUILDINGS' DAMAGE GRADE CAUSED BY COAL MINING

Coal mining under buildings certainly causes surface movement and deformation, therefore, it brings about deformation even fracture for buildings. It is an important task to evaluate correcly the buildings’ damage grabe caused by coal mining. Fuzzy comprehensive evaluation,considering some factors of buildings’ fracture, has been applied to analyze the masonry structure buildings’ damage grade affer coal mining in this paper. It provides a scientific basis for buildings’reidercement before mining and maintenance or compensation after mining.

Study on new technique of rapidly following curtain filling

The present problem of mining of narrow and gentle dip vein was analyzed. A new technique of rapidly following curtain filling was put forward. The results show that the new technique is feasible, has the characteristic to make the whole curtain wall filter, makes relative density of the filling tailings slurry reach saturation of 78.0% 80.0% in 25 min, and keeps the roof of mined out space stable in 60 min. The new technique of the rapidly following curtain filling has solved the difficult problem of the filling body filtering slowly and promptly controlling underground pressure, which cannot be solved in traditional ways.

Exploitation technology of pressure relief coalbed methane in vertical surface wells in the Huainan coal mining area

Exploitation technology of pressure relief coalbed methane in vertical surface wells is a new method for exploration of gas and coalbed methane exploitation in mining areas with high concentrations of gas, where tectonic coal developed. Studies on vertical surface well technology in the Huainan Coal Mining area play a role in demonstration in the use of clean, new energy resources, preventing and reducing coal mine gas accidents and protecting the environment. Based on the practice of gas drainage engineering of pressure relief coalbed methane in vertical surface wells and combined with relative geological and exploration en- gineering theories, the design principles of design and structure of wells of pressure relief coalbed methane in vertical surface wells are studied. The effects of extraction and their causes are discussed and the impact of geological conditions on gas production of the vertical surface wells are analyzed. The results indicate that in mining areas with high concentrations of gas, where tectonic coal developed, a success rate of pressure relief coalbed methane in surface vertical well is high and single well production usually great. But deformation due to coal exploitation could damage boreholes and cause breaks in the connection between aquifers and bore-holes, which could induce a decrease, even a complete halt in gas production of a single well. The design of well site location and wellbore configuration are the key for technology. The development of the geological conditions for coalbed methane have a significant effect on gas production of coalbed methane wells.

Trial of small gateroad pillar in top coal caving longwall mining of large mining height

Coal seams in Tashan Mine of Datong Coal Group in China average 15 m thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 3.8 m and the top coal caving height was 11.2 m. The gateroad pillar between panels was 38 m. During retreat mining,serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore,pillarless mining was experimented. Using numerical modeling and comparative study of cases of similar mining condition,it was decided to employ a 6 m wide pillar,rather than the previous 38 m wide pillar.Support system for the gateroads was designed and implemented. During gateroad development,pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion. Since the development of gateroad has just completed,and retreat mining has not begun,the effectiveness of the proposed methods is unknown at this point. However,monitoring will continue until after mining.The results will be published in a separate paper.

Study on relation between tectonic stress and coal-mining subsidence with similar material simulation

Using a minitype and stress-type test device for similar material simulation of coal-mining subsidence, the relation between tectonic stress and coal-mining subsidence was successfully simulated, furthermore, the test period of similar material simulation was obviously shortened and the test process was more dexterous and convenient. To do simi-lar material simulation with the minitype and stress-type test device was feasible and high-efficient. Bringing two models with the same geological and mining conditions to bear lateral compressive stress and tensile stress respectively and simulating the process of underground mining, the test results indicate that: under the compressive stress, the col-lapse of the coal roof occurs belatedly and the damaged range in cover of coal seam is smaller, therefore the movement and deformation of the cover and its damage to the ground geological environment are not evident; whereas under tensile stress, the situation is contrary to which mentioned above. A conclusion was obtained from the test that the ground environment hazards in coal mining areas were controlled by the regional geo-logical tectonic stress field.

Field application of non-blasting mechanized mining using high-frequency impact hammer in deep hard rock mine

A non-blasting mechanized mining experiment was carried out with a high-frequency impact hammer,and the daily mining performance was recorded to explore the applicability of the high-frequency impact hammer in deep hard rock mines.Before the field application,the scope of the excavation damage zone was monitored,and rock samples were obtained from the ore body to be mined to carry out a series of laboratory experiments.Field application results show that the overall excavation efficiency reaches 50.6 t/h,and the efficiency of pillar excavation after excavating stress relief slot reaches 158.2 t/h.The results indicate that the non-blasting mechanized mining using high-frequency impact hammer has a good application in deep hard rock mines,and the stress relief slot is conducive to mechanical excavation.In addition,the high-frequency impact hammer also exhibits the advantages of high utilization rate of labor hours,small lumpiness of spalling ore,little dust,and little excavation damage.Finally,according to the field application and laboratory experiment results,a non-blasting mechanized mining method for hard rock mines based on high-frequency impact hammer is proposed.

STUDY ON GATEWAY BOLTING EXCAVATED IN INCLINED COAL SEAM

A typical gateway is analyzed using fully-deformable discrete element method. The fractured zone around the gateway is measured in field. Based on the measurement results and theoretical analysis, a comprehensive support scheme adopting bolt and steel belt is proposed. Discrete element method is used to assess the bolting scheme, and displacement monitoring in field is also carried out. Having been put into practice, it is proved that the scheme is both successful and rational. According to theoretical analysis and monitoring in field, some important keynotes that should be noticed in gateway bolting practice are presented as well.

bStudy on constitutive relationship of coal based on conventional triaxial compression test

Constitutive relationship of coal under triaxial compression must be determined during solving the theoretical calculation and numerical simulation about coal body failure. This paper carried out conventional triaxial compression test on No.3 coal of Baodian Colliery using MTS815.03 servo-controlled rock mechanical test system. The results indicate that the failure process of coal can be divided into 5 stages： densification stage, apparent linear elastic deformation stage, accelerated inelastic deformation stage, fracture and developing stage and plasticity flow stage. Combined with the test results, the constitutive relationship model of coal can be simplified as the four segments of straight line model of elastic-plastic hardening-plastic softening-residual perfectly plastic. Through fitting calculation of test data, the segmented constitutive equation of coal can be obtained.

3D-FSM·DDM IBEM numerical system of multi-medium

Based on the idea of the developed 3D-FSM.DDM boundary element method, the field with muti-medium was formulized firstly, then connected at the interface of two fields according to the continuous conditions of stress and displacement, after that, a boundary value problem with unified model was formed and solved. Ultimately, an applied numerical simulation system was developed. It was compared with the model having analytical solution for verifying the applicability and the calculating precision.

Strata behavior in extra-thick coal seam mining with upward slicing backfilling technology

Based on the character of upward slicing backfilling mining and the condition of Gonggeyingzi coal mine in Inner Mongolia,this paper describes the studies of the strata behavior and the stress distribution in the process of backfilling mining in extra-thick coal seams.This was achieved by setting up and analyzing the elastic foundation beam model using the ABAQUS software.The results show that:(1) With the gradual mining of different slices,the roof appears to bend continuously but does not break.The vertical stress in the roof decreases and the decreasing amplitude reduces,while the tensile stress in the roof grows with the mining slices and the maximum tensile stress will not exceed the allowable tensile stress.(2) The front vertical stress at the working face exceeds the rear vertical stress and both show a trend of decrease with decreasing amplitude of decrease.(3) The slices mined early have more influence on the surrounding rock than the later ones.Similarly,the strata behavior experiences the same trend.The field measured data show that the roof does not break during the mining process,which is consistent with the conclusion.

The test research on partial relieving pressure for the entry in the deep mine under high stress and friable surrounding rock

Based on the geological condition of Zhangxiaolou deep mine in Xuzhou mining area, under 986 m in depth, 20.6-31.6 MPa in maximum horizontal principal stress, and friable and fractured surrounding rock, test researches on partial relieving pressure were completed for the entry with U-steel arched yielding support. The relieving pressure parameters, technology process and results of springing blasting by boreholes and excavating pockets in the two sides of entry were introduced. It is demonstrated that springing will not be shaped under the condition of single borehole arrangement after exploded, the arrangement by a group, it will make borehole bottom form springing in 0.6-0.8 m in diameter, that convergence of two sides and roof to floor have some increments by using springing blasting for reliving pressure. This kind of method for reliving pressure is not suitable to use in the deep mine, and that the convergence of two sides obviously declined by excavating pocket in two sides, it can be still used in the entry with metal support, while maintenance of entry in deep mines is difficult, and can not be supported by bolt or bolt with wire mesh.

Research on Ground Movement Laws for Strip Mining Under Thick Alluvium

With the discrete element method, the simulation and analysis of a series of numerical models were made. This research revealed ground movement laws for strip mining under thick alluvium and gave calculation formulae for the maximum ground subsidence and horizontal movement as a function of basement rock thickness and mining width, thus providing sound evidence for future strip mining under thick alluvium.