A NiTi@Mg interpenetrating phase composite with high strength and lightweight was prepared by additive manufacturing(AM)and infiltration technology,and the interface bonding,three-point bending properties and cyclic c...A NiTi@Mg interpenetrating phase composite with high strength and lightweight was prepared by additive manufacturing(AM)and infiltration technology,and the interface bonding,three-point bending properties and cyclic compressive properties of NiTi@Mg composites were investigated.The results show that the metallurgically bonded interface is formed at the NiTi/Mg interfaces.The bending strength and compressive strength of the NiTi@Mg composite are 2.5 and 1.7 times higher than those of the NiTi scaffold,respectively.During the bending deformation process,a large number of dislocations are observed to accumulate in the soft Mg area at the interface.Furthermore,the finite element model showed that the stress accumulation area,where the bending crack is initiated,is located at the interface of NiTi and Mg.The strengthening mechanism of NiTi@Mg composites is attributed to the twinning strengthening of Mg and heterogeneous structure strengthening.展开更多
C/C composites with banded structure pyrocarbon were fabricated by fast chemical vapor infiltration（CVI）,with C3H6 as carbon source,N2 as carrier gas,and three-dimensional（3D） 12K PAN-based carbon fabric with high...C/C composites with banded structure pyrocarbon were fabricated by fast chemical vapor infiltration（CVI）,with C3H6 as carbon source,N2 as carrier gas,and three-dimensional（3D） 12K PAN-based carbon fabric with high density of 0.94 g/cm3 as preform.Experimental results indicated that the fracture characteristics of C/C composites were closely related to the frequency of high-temperature treatment（HTT） at the break of CVI process.According to the load？displacement curves,C/C composites showed a pseudoplastic fracture after twice of HTT.After three times of HTT,load？displacement curves tended to be stable with a decreasing bending strength at 177.5 MPa.Delamination failure and intrastratal fiber fracture were observed at the cross-section of C/C composites by scanning electronic microscope.Because the content of pyrocarbon and fibers has a different distribution in layers,the C/C composites show different fracture characteristics at various regions,which leads to good toughness and bending strength.展开更多
In order to develop the warming bending technology of the large diameter thin-walled（LDTW） commercial pure titanium alloy CP-Ti tubes, the warm bending mechanism of the extrados and intrados of LDTW CP-Ti tubes was ...In order to develop the warming bending technology of the large diameter thin-walled（LDTW） commercial pure titanium alloy CP-Ti tubes, the warm bending mechanism of the extrados and intrados of LDTW CP-Ti tubes was researched. By EBSD analysis and Vickers hardness test, the changes of microstructure and strength of the tubes at different bending temperatures of 293, 423 and 573 K, were analyzed. The results show： 1） The extrados of the bent tube deforms mainly by slip, along with few twinning, and the preferred orientation is similar to that of the initial tube; the intrados of the bent tube experiences compression deformation mainly by {1 012} tensile twinning, and the twinning makes the preferred orientation of wall materials change sharply. 2） The Vickers hardness values of both the extrados and intrados of the samples after bending increase greatly; the Vickers hardness values of the intrados are much higher than those of the extrados, and Vickers hardness values of the RD-TD planes are always higher than those of the RD-LD planes, which are related to the different deformation mechanisms.展开更多
Updating parameters according to the driving rate of input, the rate-dependent Prandtl-Ishlinskii （PI） model is widely used in hysteresis modeling and compensation. In order to improve the modeling accuracy, two PI ...Updating parameters according to the driving rate of input, the rate-dependent Prandtl-Ishlinskii （PI） model is widely used in hysteresis modeling and compensation. In order to improve the modeling accuracy, two PI models identified at low and high driving rates separately are incorporated through a combination law. For the piezo- driven flexure-based mechanism, the very low damping ratio makes it easy to excite the structural vibration. As a re- suit, the measured hysteresis loop is greatly distorted and the modeling accuracy of the identified P1 model is signifi- cantly affected. In this paper, a novel time-efficient parameter identification method which utilizes the superimposed sinusoidal signals as the control input is proposed. This method effectively avoids the excitation of the structural vibra- tion. In addition, as the driving rate of the superimposed sinusoidal signals covers a wide range, all the coefficients required for modeling the rate-dependence can be identified through only one set of experimental data. Hysteresis modeling and trajectory tracking experiments were performed on a 2-DOF piezo-driven flexure-based mechanism. The experimental results show that the combined hysteresis model maintains the modeling accuracy over the entire work- ing range of the flexure-based mechanism. The mechanism＇s hysteresis is significantly suppressed by the use of the inverse PI model as the feedforward controller; and better result is achieved when a feedback loop is also incorporated. The tracking performance of the flexure-based mechanism is greatly improved.展开更多
It was reported that exogenous hydrogen peroxide （H2O2） can induce primary root bend in Arabidopsis and pea. However, the mechanism remains unclear. Here we explored the mechanism underlying this phenomenon by using...It was reported that exogenous hydrogen peroxide （H2O2） can induce primary root bend in Arabidopsis and pea. However, the mechanism remains unclear. Here we explored the mechanism underlying this phenomenon by using the pea （Pisum sativum L.） variety ＂longwan No. 1＂ The results showed that the endogenous indole-3-acetic acid （IAA） content decreased and gibberellin A3 （GA3） content increased in the curving primary pea root induced by H2O2. Meanwhile, both of the two hormones asymmetrically distributed in the inside and outside parts of the curving root. Also, the starch content decreased due to the increased a-amylase activity in this process. However, exogenous Ca2＋ can relieve the horizontal bending of pea root induced by H2O2 and altered the contents of endogenous IAA and GA3. A working model was proposed： Exogenous H2O2 causes the increase in GA3 content, and GA3 stimulates the activity of or-amylase, which leads to the hydrolysis of starch, and then the root lost the gravity perceiving. The asymmetric distribution of IAA and GA3 in two sides of curving root may cause the horizontal bending.Exogenous Ca^2＋ can relieve root bending through altering the endogenous IAA and GA3 contents.展开更多
基金supported by the National Natural Science Foundation of China (Nos.52001030,51803200,52105356,52003104)the Natural Science Foundation of Hunan Province,China (Nos.2021JJ40590,2021JJ40600)+6 种基金the Natural Science Foundation of Hunan Province Youth Fund,China (No.2021JJ20011)the Major Research Plan of the National Natural Science Foundation of China (No.92166112)the Project of MOE Key Lab of Disaster Forecast and Control in Engineering in Jinan University,China (No.20200904006)the Guangdong Province Basic and Applied Basic Research Foundation,China (No.2020B1515420004)the Guangxi Key Laboratory of Information Materials,China (No.211003-K)the Open Project Program of the State Key Laboratory of Mechanical Transmissions in Chongqing University,China (No.SKLMT-MSKFKT-202102)the Fundamental Research Funds for the Central Universities,China (No.21622110)。
文摘A NiTi@Mg interpenetrating phase composite with high strength and lightweight was prepared by additive manufacturing(AM)and infiltration technology,and the interface bonding,three-point bending properties and cyclic compressive properties of NiTi@Mg composites were investigated.The results show that the metallurgically bonded interface is formed at the NiTi/Mg interfaces.The bending strength and compressive strength of the NiTi@Mg composite are 2.5 and 1.7 times higher than those of the NiTi scaffold,respectively.During the bending deformation process,a large number of dislocations are observed to accumulate in the soft Mg area at the interface.Furthermore,the finite element model showed that the stress accumulation area,where the bending crack is initiated,is located at the interface of NiTi and Mg.The strengthening mechanism of NiTi@Mg composites is attributed to the twinning strengthening of Mg and heterogeneous structure strengthening.
基金Project (50802115) supported by the National Natural Science Foundation of ChinaProject (2011CB605801) supported by the National Basic Research Program of China
文摘C/C composites with banded structure pyrocarbon were fabricated by fast chemical vapor infiltration（CVI）,with C3H6 as carbon source,N2 as carrier gas,and three-dimensional（3D） 12K PAN-based carbon fabric with high density of 0.94 g/cm3 as preform.Experimental results indicated that the fracture characteristics of C/C composites were closely related to the frequency of high-temperature treatment（HTT） at the break of CVI process.According to the load？displacement curves,C/C composites showed a pseudoplastic fracture after twice of HTT.After three times of HTT,load？displacement curves tended to be stable with a decreasing bending strength at 177.5 MPa.Delamination failure and intrastratal fiber fracture were observed at the cross-section of C/C composites by scanning electronic microscope.Because the content of pyrocarbon and fibers has a different distribution in layers,the C/C composites show different fracture characteristics at various regions,which leads to good toughness and bending strength.
基金Projects(50905144,51275415)supported by the National Natural Science Foundation of ChinaProject supported by the Program for New Century Excellent Talents in University,ChinaProject(B08040)supported by the Program of Introducing Talents of Discipline to Universities,China("111"Project)
文摘In order to develop the warming bending technology of the large diameter thin-walled（LDTW） commercial pure titanium alloy CP-Ti tubes, the warm bending mechanism of the extrados and intrados of LDTW CP-Ti tubes was researched. By EBSD analysis and Vickers hardness test, the changes of microstructure and strength of the tubes at different bending temperatures of 293, 423 and 573 K, were analyzed. The results show： 1） The extrados of the bent tube deforms mainly by slip, along with few twinning, and the preferred orientation is similar to that of the initial tube; the intrados of the bent tube experiences compression deformation mainly by {1 012} tensile twinning, and the twinning makes the preferred orientation of wall materials change sharply. 2） The Vickers hardness values of both the extrados and intrados of the samples after bending increase greatly; the Vickers hardness values of the intrados are much higher than those of the extrados, and Vickers hardness values of the RD-TD planes are always higher than those of the RD-LD planes, which are related to the different deformation mechanisms.
基金Supported by National Natural Science Foundation of China (No. 51175372)National Key Special Project of Science and Technology of China (No. 2011ZX04016-011)
文摘Updating parameters according to the driving rate of input, the rate-dependent Prandtl-Ishlinskii （PI） model is widely used in hysteresis modeling and compensation. In order to improve the modeling accuracy, two PI models identified at low and high driving rates separately are incorporated through a combination law. For the piezo- driven flexure-based mechanism, the very low damping ratio makes it easy to excite the structural vibration. As a re- suit, the measured hysteresis loop is greatly distorted and the modeling accuracy of the identified P1 model is signifi- cantly affected. In this paper, a novel time-efficient parameter identification method which utilizes the superimposed sinusoidal signals as the control input is proposed. This method effectively avoids the excitation of the structural vibra- tion. In addition, as the driving rate of the superimposed sinusoidal signals covers a wide range, all the coefficients required for modeling the rate-dependence can be identified through only one set of experimental data. Hysteresis modeling and trajectory tracking experiments were performed on a 2-DOF piezo-driven flexure-based mechanism. The experimental results show that the combined hysteresis model maintains the modeling accuracy over the entire work- ing range of the flexure-based mechanism. The mechanism＇s hysteresis is significantly suppressed by the use of the inverse PI model as the feedforward controller; and better result is achieved when a feedback loop is also incorporated. The tracking performance of the flexure-based mechanism is greatly improved.
基金supported by the National Natural Science Foundation of China(31160304)Gansu Provincial Key Laboratory of Aridland Crop Science,Gansu Agricultural University,China
文摘It was reported that exogenous hydrogen peroxide （H2O2） can induce primary root bend in Arabidopsis and pea. However, the mechanism remains unclear. Here we explored the mechanism underlying this phenomenon by using the pea （Pisum sativum L.） variety ＂longwan No. 1＂ The results showed that the endogenous indole-3-acetic acid （IAA） content decreased and gibberellin A3 （GA3） content increased in the curving primary pea root induced by H2O2. Meanwhile, both of the two hormones asymmetrically distributed in the inside and outside parts of the curving root. Also, the starch content decreased due to the increased a-amylase activity in this process. However, exogenous Ca2＋ can relieve the horizontal bending of pea root induced by H2O2 and altered the contents of endogenous IAA and GA3. A working model was proposed： Exogenous H2O2 causes the increase in GA3 content, and GA3 stimulates the activity of or-amylase, which leads to the hydrolysis of starch, and then the root lost the gravity perceiving. The asymmetric distribution of IAA and GA3 in two sides of curving root may cause the horizontal bending.Exogenous Ca^2＋ can relieve root bending through altering the endogenous IAA and GA3 contents.
