The physical absorption of CO2 in water containing different types of particles was studied in a micro-channel operated under Taylor flow. The maximum enhancement factors of 1.43-2.15 were measured for activated carb...The physical absorption of CO2 in water containing different types of particles was studied in a micro-channel operated under Taylor flow. The maximum enhancement factors of 1.43-2.15 were measured for activated carbon （AcC） particles. The analysis shows that the enhancement effect can be attributed to the shuttle mechanism. Considering the separate contributions of mass transfer from bubble cap and liquid film, a heterogeneous enhance- ment model is developed. According to this model, the enhancement factors Ecap, EFilm and Eov are mainly determined by mass transfer coefficient gL （gL Cap and KL Film）, adsorptive capacity of particles m, and coverage fraction of particles at gas-liquid interface （. With both effects of particle-to-interface adhesion and apparent viscosity included, the model nredicts the enhancement effect of AcC varticles reasonably well.展开更多
The main focus of the present work is to investigate Critical Heat Flux (CHF) enhancement using CuO nanofluid relative to CHF of pure water. To estimate the effect of nanoparticles on the CHF, pool boiling CHF values ...The main focus of the present work is to investigate Critical Heat Flux (CHF) enhancement using CuO nanofluid relative to CHF of pure water. To estimate the effect of nanoparticles on the CHF, pool boiling CHF values were measured for various volume concentrations of CuO nanofluid and compared with pure water. CHF enhancement of 130% was recorded at 0.2 % by volume of CuO nano-fluids. Surface roughness of the heater surface exposed to three measured heating cycles indicated surface modifications at different volume concentrations of nanofluid. SEM image of the heater surface revealed porous layer build up, which is thought to be the reason for CHF enhancement.展开更多
Pool boiling of saturated water on a plain Ti surface and surfaces covered with vertically-oriented TiO2 nanotube arrays(NTAs) has been studied.The technique of potentiostatic anodization using non-aqueous electrolyte...Pool boiling of saturated water on a plain Ti surface and surfaces covered with vertically-oriented TiO2 nanotube arrays(NTAs) has been studied.The technique of potentiostatic anodization using non-aqueous electrolytes was adopted to fabricate three types of TiO2 NTAs distinguished by their anodization time.Compared to the bare Ti surface,the incipient boiling wall superheat on the TiO2 NTAs was decreased by 11 K.Both the critical heat flux and heat transfer coefficient of pool boiling on the TiO2 NTAs were higher than those from boiling on a bare Ti surface.The measured maximum critical heat flux and heat transfer coefficient values were 186.7 W/cm2 and 6.22 W/cm2K,respectively.Different performances for the enhancement of heat transfer by the three types of TiO2 NTAs were attributed to the different degrees of deformation in the nanostructure during boiling.Long-term performance of the nanomaterial-coated surfaces for enhanced pool boiling showed degradation of the TiO2 NTAs prepared with an anodization time of 3 hours.展开更多
MoO3 nanobelts （NBs） having different properties have been synthesized via a physical vapor deposition （PVD） method. The crystallographic structures and morphologies of the NBs were characterized by X-ray diffract...MoO3 nanobelts （NBs） having different properties have been synthesized via a physical vapor deposition （PVD） method. The crystallographic structures and morphologies of the NBs were characterized by X-ray diffraction, transmission electron microscopy and scanning electron microscopy. Electrical measurements were performed and the profound piezoresistive effect in MoO3 experimentally studied and verified. Factors that influence the gauge factor, such as NB size, doping concentration and atmosphere composition, are discussed and analyzed. Gas sensing performance was also tested in devices and it was demonstrated that by applying strain to the gas sensor, its sensing performance could be effectively tuned and enhanced. This study provides the first demonstration of significant piezoresistivity in MoO3 NBs and the first illustration of a generic mechanism by means of which this effect can be coupled with other electronic modulation measures to afford better device performance and broader material functionality.展开更多
A waste heat recovery and denitrification system was developed for improving energy conservation and emissions control especially for control of PM2.5 particles and haze. The system uses enhanced heat and mass transfe...A waste heat recovery and denitrification system was developed for improving energy conservation and emissions control especially for control of PM2.5 particles and haze. The system uses enhanced heat and mass transfer techniques in a packed heat exchange tower with self-rotation and zero-pressure spraying, low temperature NO oxidation by ozone, and neutralization with an alkali solution. Operating data in a test project gave NOx in the exhaust flue gas of less than 30 mg/Nm3 with an ozone addition rate of 8 kg/h and spray water p H of 7.5–8, an average heat recovery of 3 MW, and an average heat supply of 7.2 MW.展开更多
This paper analyzes the effects of nanoporous surface on heat transfer temperaments of assorted thermal conductingmaterials. A phenomenal proposal of wielding the surface roughness to ameliorate the heat transfer rate...This paper analyzes the effects of nanoporous surface on heat transfer temperaments of assorted thermal conductingmaterials. A phenomenal proposal of wielding the surface roughness to ameliorate the heat transfer ratehas been discovered. The maximum increase of heat transfer rate procured by nanoporous layers is 133.3% higherthan the polished bare metals of surface roughness 0.2μm. This plays an imperative role in designing compact refrigerationsystems, chemical and thermal power plants. Experimental results picture a formidable upswing of58.3% heat transfer in chemically etched metals of surface roughness 3 μm, 133.3% in nanoporous surface of porosity75-95 nm formed by electrochemical anodization, and porosity of 40-50 nm formed by spray pyrolysis increasesthe heat transfer by 130%. Effects of porosity, flow velocity and scaling on the energy transfer are alsoscrutinized. This paper also analyzes the multifarious modes of nanoporous fabrication, to contrive both prodigiousand provident system.展开更多
基金Supported by the National＇Natural Science Foundation of China （20706041, 20876109）, and the Natural Science Foundation of Tianjin, China （09JCYBJC06500）.
文摘The physical absorption of CO2 in water containing different types of particles was studied in a micro-channel operated under Taylor flow. The maximum enhancement factors of 1.43-2.15 were measured for activated carbon （AcC） particles. The analysis shows that the enhancement effect can be attributed to the shuttle mechanism. Considering the separate contributions of mass transfer from bubble cap and liquid film, a heterogeneous enhance- ment model is developed. According to this model, the enhancement factors Ecap, EFilm and Eov are mainly determined by mass transfer coefficient gL （gL Cap and KL Film）, adsorptive capacity of particles m, and coverage fraction of particles at gas-liquid interface （. With both effects of particle-to-interface adhesion and apparent viscosity included, the model nredicts the enhancement effect of AcC varticles reasonably well.
文摘The main focus of the present work is to investigate Critical Heat Flux (CHF) enhancement using CuO nanofluid relative to CHF of pure water. To estimate the effect of nanoparticles on the CHF, pool boiling CHF values were measured for various volume concentrations of CuO nanofluid and compared with pure water. CHF enhancement of 130% was recorded at 0.2 % by volume of CuO nano-fluids. Surface roughness of the heater surface exposed to three measured heating cycles indicated surface modifications at different volume concentrations of nanofluid. SEM image of the heater surface revealed porous layer build up, which is thought to be the reason for CHF enhancement.
基金supported by the National Natural Science Foundation of China (Grant Nos. 11004054,50825603,U1034004)the Fundamental Research Funds for the Central Universities
文摘Pool boiling of saturated water on a plain Ti surface and surfaces covered with vertically-oriented TiO2 nanotube arrays(NTAs) has been studied.The technique of potentiostatic anodization using non-aqueous electrolytes was adopted to fabricate three types of TiO2 NTAs distinguished by their anodization time.Compared to the bare Ti surface,the incipient boiling wall superheat on the TiO2 NTAs was decreased by 11 K.Both the critical heat flux and heat transfer coefficient of pool boiling on the TiO2 NTAs were higher than those from boiling on a bare Ti surface.The measured maximum critical heat flux and heat transfer coefficient values were 186.7 W/cm2 and 6.22 W/cm2K,respectively.Different performances for the enhancement of heat transfer by the three types of TiO2 NTAs were attributed to the different degrees of deformation in the nanostructure during boiling.Long-term performance of the nanomaterial-coated surfaces for enhanced pool boiling showed degradation of the TiO2 NTAs prepared with an anodization time of 3 hours.
文摘MoO3 nanobelts （NBs） having different properties have been synthesized via a physical vapor deposition （PVD） method. The crystallographic structures and morphologies of the NBs were characterized by X-ray diffraction, transmission electron microscopy and scanning electron microscopy. Electrical measurements were performed and the profound piezoresistive effect in MoO3 experimentally studied and verified. Factors that influence the gauge factor, such as NB size, doping concentration and atmosphere composition, are discussed and analyzed. Gas sensing performance was also tested in devices and it was demonstrated that by applying strain to the gas sensor, its sensing performance could be effectively tuned and enhanced. This study provides the first demonstration of significant piezoresistivity in MoO3 NBs and the first illustration of a generic mechanism by means of which this effect can be coupled with other electronic modulation measures to afford better device performance and broader material functionality.
基金supported by the National Basic Research Program of China(Grant No.2013CB228301)
文摘A waste heat recovery and denitrification system was developed for improving energy conservation and emissions control especially for control of PM2.5 particles and haze. The system uses enhanced heat and mass transfer techniques in a packed heat exchange tower with self-rotation and zero-pressure spraying, low temperature NO oxidation by ozone, and neutralization with an alkali solution. Operating data in a test project gave NOx in the exhaust flue gas of less than 30 mg/Nm3 with an ozone addition rate of 8 kg/h and spray water p H of 7.5–8, an average heat recovery of 3 MW, and an average heat supply of 7.2 MW.
文摘This paper analyzes the effects of nanoporous surface on heat transfer temperaments of assorted thermal conductingmaterials. A phenomenal proposal of wielding the surface roughness to ameliorate the heat transfer ratehas been discovered. The maximum increase of heat transfer rate procured by nanoporous layers is 133.3% higherthan the polished bare metals of surface roughness 0.2μm. This plays an imperative role in designing compact refrigerationsystems, chemical and thermal power plants. Experimental results picture a formidable upswing of58.3% heat transfer in chemically etched metals of surface roughness 3 μm, 133.3% in nanoporous surface of porosity75-95 nm formed by electrochemical anodization, and porosity of 40-50 nm formed by spray pyrolysis increasesthe heat transfer by 130%. Effects of porosity, flow velocity and scaling on the energy transfer are alsoscrutinized. This paper also analyzes the multifarious modes of nanoporous fabrication, to contrive both prodigiousand provident system.
