多预警机强效区覆盖与仿真计算

根据预警机阵位巡逻强效区、覆盖区定义,推导双预警机强效区重叠区面积公式,讨论探测区重叠与面积覆盖比例关系,计算分析不同探测距离、不同跑道长度条件时双预警机探测覆盖面积及覆盖率,为双预警机活动空域受限战术部署提供理论参考。

预警机巡逻探测区域建模及效能分析

已有文献中对于预警机巡逻探测区域的计算缺乏理论证明,本文针对装备360度全方位覆盖型预警雷达的预警机,对其两种常用巡逻航线的巡逻探测总覆盖区、强效区和探测盲区进行建模,首次给出详细的理论推导和计算公式。并对能够影响探测性能的预警机巡逻航线参数进行了仿真和分析。仿真结论可作为预警机巡逻区域设置和巡逻航线规划的参考,以最大化预警探测效能。

Characteristic and optimization of ferrite-rich sulfoaluminate-based composite cement suitable for cold region tunnels

To develop suitable grouting materials for water conveyance tunnels in cold regions,firstly,this study investigated the performance evolution of ferrite-rich sulfoaluminate-based composite cement(FSAC grouting material)at 20 and 3℃.The results show that low temperature only delays the strength development of FSAC grouting material within the first 3 d.Then,the effect of four typical early strength synergists on the early properties of FSAC grouting material was evaluated to optimize the early(£1 d)strength at 3℃.The most effective synergist,Ca(HCOO)_(2),which enhances the low-temperature early strength without compromising fluidity was selected based on strength and fluidity tests.Its micro-mechanism was analyzed by XRD,TG,and SEM methods.The results reveal that the most suitable dosage range is 0.3 wt%−0.5 wt%.Proper addition of Ca(HCOO)_(2)changed the crystal morphology of the hydration products,decreased the pore size and formed more compact hydration products by interlocking and overlapping.However,excessive addition of Ca(HCOO)_(2)inhibited the hydration reaction,resulting in a simple and loose structure of the hydration products.The research results have reference value for controlling surrounding rock deformation and preventing water and mud inrushes during the excavation in cold region tunnels.

基于兵力投入的预警机巡逻航线规划研究

针对预警机巡逻探测目标区域的需求,基于强效区探测数学模型,分析了航线规划的重要影响因素。综合预警机雷达性能、载机飞行特性及敌方威胁程度因素,构建了目标区域全覆盖的兵力投入量化模型,并推导了单机巡逻航线规划、双机和三机协同巡逻航线规划的解析方法。

Effects of under-aging treatment on microstructure and mechanical properties of squeeze-cast Al-Zn-Mg-Cu alloy

The effects of under-aging treatment on the microstructure and mechanical properties of Al-Zn-Mg-Cu alloy produced by squeeze casting were investigated using optical microscopy(OM),X-ray diffractometry(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM)and hardness and tensile testing.The results showed that most of secondary phases were dissolved intoα(Al)matrix while no significant grain growth happened under the condition of solution treatment at 470°C for 4 h.Due to the strengthening effect of GP zones,for alloys treated by under-aging process,the increase of aging time and aging temperature improved the ultimate tensile strength(UTS)and yield strength(YS),but decreased the elongation(δ)to some extent.By utilizing appropriate aging time and temperature,the best combination of strength and ductility could be obtained to fulfill the design requirements of automobile components.

Direct Radiative Forcing and Climatic Effects of Aerosols over East Asia by RegCM3

The authors used a high-resolution regional climate model （RegCM3） coupled with a chemistry/ aerosol module to simulate East Asian climate in 2006 and to test the climatic impacts of aerosols on regional- scale climate. The direct radiative forcing and climatic effects of aerosols （dust, sulfate, black carbon, and organic carbon） were discussed. The results indicated that aerosols generally produced negative radiative forcing at the top-of-the-atmosphere （TOA） over most areas of East Asia. The radiative forcing induced by aerosols exhibited significant seasonal and regional variations, with the strongest forcing occurring in summer. The aerosol feed- backs on surface air temperature and precipitation were clear. Surface cooling dominated features over the East Asian continental areas, which varied in the approximate range of-0.5 to -2℃ with the maximum up to -3℃ in summer over the deserts of West China. The aerosols induced complicated variations of precipitation. Except in summer, the rainfall generally varied in the range of-1 to 1 mm d^-1 over most areas of China.

Impact of Different East Asian Summer Monsoon Circulations on Aerosol-Induced Climatic Effects

The different spatial distributions of aerosol-induced direct radiative forcing and climatic effects in a weak （2003） and a strong （2006） East Asian summer monsoon （EASM） circulation were simulated using a high-resolution regional climate model （RegCM3）.Results showed that the atmospheric circulations of summer monsoon have direct relations with transport of aerosols and their climatic effects.Both the top-of-the-atmosphere （TOA） and the surface-negative radiative forcing of aerosols were stronger in weak EASM circulations.The main difference in aerosol-induced negative forcing in two summers varied between 2 and 14 W m-2 from the Sichuan Basin to North China,where a maximum in aerosol-induced negative forcing was also noticed in the EASM-dominated areas.The spatial difference in the simulated aerosol optical depth （AOD） in two summers generally showed the similar pictures.Surface cooling effects induced by aerosols were spatially more uniform in weak EASM circulations and cooler by about 1-4.5℃.A preliminary analysis here indicated that a weaker low-level wind speed not conducive to the transport and diffusion of aerosols could make more contributions to the differences in the two circulations.

Bonding between Aggregates and Cement Pastes in Concrete

This investigation was carried out to study the effect of aggregate roughness on ITZ （interfacial transition zone） at same water/cement ratio and the influence of silica fume on the bond strength. On the experimental side, two types of aggregates （limestone and granite） were used, which were prepared with broken surface. Cement （Type I） was used with same w/c ratio for all batches. In order to study the effect of silica fume on the bond, the same mixes were produced with 8% silica fume. Three different tests were performed： ＂pull a part＂, Brazilian test and compressive strength test. The specimens for Brazilian and compressive strength were tested after 28 days, while the ＂pull a part＂ specimens were tested after 29 days. The result showed that the bond strength is influenced by the surface roughness of aggregate. For the same mix, limestone recorded higher bond strength than granite. Moreover, the bond strength is increased by adding the silica fume.