The EGR (exhaust gas recirculation) technique can greatly reduce the NOx emission of diesel engines, especially when an EGR cooler is employed. Numerical simulations are applied to study the flow field and temperature...The EGR (exhaust gas recirculation) technique can greatly reduce the NOx emission of diesel engines, especially when an EGR cooler is employed. Numerical simulations are applied to study the flow field and temperature distributions inside the EGR cooler. Three different models of EGR cooler are investigated, among which model A is a traditional one, and models B and C are improved by adding a helical baffle in the cooling area. In models B and C the entry directions of cooling water are different, which mostly influences the flow resistance. The results show that the improved structures not only lengthen the flow path of the cooling water, but also enhance the heat exchange rate between the cool and hot media. In conclusion we suggest that the improved structures are more powerful than the traditional one.展开更多
Taking the ratio of heat transfer area to net power and heat recovery efficiency into account, a multi-objective mathematical model was developed for organic Rankine cycle （ORC）. Working fluids considered were R123,...Taking the ratio of heat transfer area to net power and heat recovery efficiency into account, a multi-objective mathematical model was developed for organic Rankine cycle （ORC）. Working fluids considered were R123, R134a, R141b, R227ea and R245fa. Under the given conditions, the parameters including evaporating and condensing pressures, working fluid and cooling water velocities were optimized by simulated annealing algorithm. The results show that the optimal evaporating pressure increases with the heat source temperature increasing. Compared with other working fluids, R123 is the best choice for the temperature range of 100--180℃ and R141 b shows better performance when the temperature is higher than 180 ℃. Economic characteristic of system decreases rapidly with the decrease of heat source temperature. ORC system is uneconomical for the heat source temperature lower than 100℃.展开更多
Mode Water’, as a product of air-sea interaction, influences the thermal structure and circulation pattern in upper layer ocean and consequently affects the variations of climate. In this paper the recent research re...Mode Water’, as a product of air-sea interaction, influences the thermal structure and circulation pattern in upper layer ocean and consequently affects the variations of climate. In this paper the recent research results about the subtropi-cal Mode Water in the North Pacific are overiewed. A detailed description of the three kinds of Mode Water in the subtropical North Pacific and some comparisons of their similarities and differences are introduced. Some science problems that need further exploration have been raised.展开更多
Nano fluid is considered to be a class of high efficient heat transfer fluid created by dispersing some special solid nanoparticles (normally less than 100 nm) in traditional heat transfer fluid. The present experimen...Nano fluid is considered to be a class of high efficient heat transfer fluid created by dispersing some special solid nanoparticles (normally less than 100 nm) in traditional heat transfer fluid. The present experiment was conducted aiming at investigating the forced heat transfer characteristics of aqueous copper (Cu) nanofluid at varying concentration of Cu nano-particles in different flow regimes (300<Re≤16 000). The forced convective heat transfer enhancement is available both in the laminar and turbulent flow with increasing the concentration. Especially, the enhancement rate increases dramatically in laminar flow regime, for instance, the heat transfer coefficient of Cu/water nanofluid increases by two times at around Re=2 000 compared with that of base fluid water, and averagely increases by 62% at 1% volume fraction. However, the heat transfer coefficient of Cu/water decreases sharply in the transition flow regime. Furthermore, it has the trend that the heat transfer coefficient displays worse with increasing the concentration.展开更多
The characteristics of an organic Rankin cycle designed to operate with a low temperature geothermal source and constant temperature cooling water supplied from freshwater ponds typical to those found near Waddan City...The characteristics of an organic Rankin cycle designed to operate with a low temperature geothermal source and constant temperature cooling water supplied from freshwater ponds typical to those found near Waddan City in the Al Jufrah region of Libya were examined. Two working fluids were examined and it was concluded that the most suitable for this application was R-245fa. The off design performance of the organic Rankine cycle was examined and it was shown that the cycle is controlled by the performance of the condenser which is cooling water side temperature limited.展开更多
Deep ice drilling in Polar Regions plays a key role in paleo-climate, microbiological and glaciological researches. For deep ice and subglacial coring the special purpose-built electromechanical cable-suspended drills...Deep ice drilling in Polar Regions plays a key role in paleo-climate, microbiological and glaciological researches. For deep ice and subglacial coring the special purpose-built electromechanical cable-suspended drills with bottom-hole circulation are designed and explored. Used at present drilling fluid circulation systems are specified by very high fluid wastes during processing. Measurements in deep drilling projects in Antarctic and Greenland ice sheets showed that 25%-40% of the drilling fluid, pumped into the hole, is retrieved to the surface with cable and drill, and up to 45% of retrieved fluid goes to waste. This leads not only to increasing of the fluid consumption and cost of the project in general but also to severe contamination of air, surface and near-surface snow-firn layers at the drilling site. In order to reduce wastes and environmental impact, it is proposed to modify drilling fluid processing system by avoiding of evaporation and leakages of fluid as far as practicable. Drilling fluid is prepared and pumped into the hole according to predetermined program on semiautomatic mode, and volume and density of blended and pumped into the hole drilling fluid are measured continuously. Components of the drilling fluid are stored and mixed in the special closed containers equipped by pressure relief valves. Separation of drilling fluid from ice cuttings is carried out by two steps: firstly, fluid is separated with hydro extractor and then with thermal separator. To reduce the amount of removed drilling fluid with cable special squeezing collar is installed on the borehole mouth. All these arrangements are able to decrease drilling fluid wastes in many times.展开更多
The pinch point is important for analyzing heat transfer in thermodynamic cycles. With the aim to reveal the importance of determining the accurate pinch point, the research on the pinch point position is carried out ...The pinch point is important for analyzing heat transfer in thermodynamic cycles. With the aim to reveal the importance of determining the accurate pinch point, the research on the pinch point position is carried out by theoretical method. The results show that the pinch point position depends on the parameters of the heat transfer fluids and the major fluid properties. In most cases, the pinch point locates at the bubble point for the evaporator and the dew point for the condenser. However, the pinch point shills to the supercooled liquid state in the near critical conditions for the evaporator. Similarly, it shifts to the superheated vapor state with the condensing temperature approaching the critical temperature for the condenser. It even can shift to the working fluid entrance of the evaporator or the supereritical heater when the heat source fluid temperature is very high compared with the absorb- ing heat temperature. A wrong position for the pinch point may generate serious mistake. In brief, the pinch point should be founded by the itcrativc method in all conditions rather than taking for granted.展开更多
文摘The EGR (exhaust gas recirculation) technique can greatly reduce the NOx emission of diesel engines, especially when an EGR cooler is employed. Numerical simulations are applied to study the flow field and temperature distributions inside the EGR cooler. Three different models of EGR cooler are investigated, among which model A is a traditional one, and models B and C are improved by adding a helical baffle in the cooling area. In models B and C the entry directions of cooling water are different, which mostly influences the flow resistance. The results show that the improved structures not only lengthen the flow path of the cooling water, but also enhance the heat exchange rate between the cool and hot media. In conclusion we suggest that the improved structures are more powerful than the traditional one.
基金Project(2009GK2009) supported by Science and Technology Department Funds of Hunan Province,ChinaProject(08C26224302178) supported by Innovation Fund for Technology Based Firms of China
文摘Taking the ratio of heat transfer area to net power and heat recovery efficiency into account, a multi-objective mathematical model was developed for organic Rankine cycle （ORC）. Working fluids considered were R123, R134a, R141b, R227ea and R245fa. Under the given conditions, the parameters including evaporating and condensing pressures, working fluid and cooling water velocities were optimized by simulated annealing algorithm. The results show that the optimal evaporating pressure increases with the heat source temperature increasing. Compared with other working fluids, R123 is the best choice for the temperature range of 100--180℃ and R141 b shows better performance when the temperature is higher than 180 ℃. Economic characteristic of system decreases rapidly with the decrease of heat source temperature. ORC system is uneconomical for the heat source temperature lower than 100℃.
基金supported by the NSFC(No.49976004 and 40028605)National Key Program for Developing Basic Science(No.G1999043807).
文摘Mode Water’, as a product of air-sea interaction, influences the thermal structure and circulation pattern in upper layer ocean and consequently affects the variations of climate. In this paper the recent research results about the subtropi-cal Mode Water in the North Pacific are overiewed. A detailed description of the three kinds of Mode Water in the subtropical North Pacific and some comparisons of their similarities and differences are introduced. Some science problems that need further exploration have been raised.
基金supported by Basic Science Research Program through the National Research Foundation of Korea (NRF)funded by the Ministry of Education, Science and Technology (No.2012-0004544)
文摘Nano fluid is considered to be a class of high efficient heat transfer fluid created by dispersing some special solid nanoparticles (normally less than 100 nm) in traditional heat transfer fluid. The present experiment was conducted aiming at investigating the forced heat transfer characteristics of aqueous copper (Cu) nanofluid at varying concentration of Cu nano-particles in different flow regimes (300<Re≤16 000). The forced convective heat transfer enhancement is available both in the laminar and turbulent flow with increasing the concentration. Especially, the enhancement rate increases dramatically in laminar flow regime, for instance, the heat transfer coefficient of Cu/water nanofluid increases by two times at around Re=2 000 compared with that of base fluid water, and averagely increases by 62% at 1% volume fraction. However, the heat transfer coefficient of Cu/water decreases sharply in the transition flow regime. Furthermore, it has the trend that the heat transfer coefficient displays worse with increasing the concentration.
文摘The characteristics of an organic Rankin cycle designed to operate with a low temperature geothermal source and constant temperature cooling water supplied from freshwater ponds typical to those found near Waddan City in the Al Jufrah region of Libya were examined. Two working fluids were examined and it was concluded that the most suitable for this application was R-245fa. The off design performance of the organic Rankine cycle was examined and it was shown that the cycle is controlled by the performance of the condenser which is cooling water side temperature limited.
基金Supported by the National Natural Science Foundation of China(No.41276189)
文摘Deep ice drilling in Polar Regions plays a key role in paleo-climate, microbiological and glaciological researches. For deep ice and subglacial coring the special purpose-built electromechanical cable-suspended drills with bottom-hole circulation are designed and explored. Used at present drilling fluid circulation systems are specified by very high fluid wastes during processing. Measurements in deep drilling projects in Antarctic and Greenland ice sheets showed that 25%-40% of the drilling fluid, pumped into the hole, is retrieved to the surface with cable and drill, and up to 45% of retrieved fluid goes to waste. This leads not only to increasing of the fluid consumption and cost of the project in general but also to severe contamination of air, surface and near-surface snow-firn layers at the drilling site. In order to reduce wastes and environmental impact, it is proposed to modify drilling fluid processing system by avoiding of evaporation and leakages of fluid as far as practicable. Drilling fluid is prepared and pumped into the hole according to predetermined program on semiautomatic mode, and volume and density of blended and pumped into the hole drilling fluid are measured continuously. Components of the drilling fluid are stored and mixed in the special closed containers equipped by pressure relief valves. Separation of drilling fluid from ice cuttings is carried out by two steps: firstly, fluid is separated with hydro extractor and then with thermal separator. To reduce the amount of removed drilling fluid with cable special squeezing collar is installed on the borehole mouth. All these arrangements are able to decrease drilling fluid wastes in many times.
基金Project 51306198 supported by National Natural Science Foundation of China is gratefully acknowledged
文摘The pinch point is important for analyzing heat transfer in thermodynamic cycles. With the aim to reveal the importance of determining the accurate pinch point, the research on the pinch point position is carried out by theoretical method. The results show that the pinch point position depends on the parameters of the heat transfer fluids and the major fluid properties. In most cases, the pinch point locates at the bubble point for the evaporator and the dew point for the condenser. However, the pinch point shills to the supercooled liquid state in the near critical conditions for the evaporator. Similarly, it shifts to the superheated vapor state with the condensing temperature approaching the critical temperature for the condenser. It even can shift to the working fluid entrance of the evaporator or the supereritical heater when the heat source fluid temperature is very high compared with the absorb- ing heat temperature. A wrong position for the pinch point may generate serious mistake. In brief, the pinch point should be founded by the itcrativc method in all conditions rather than taking for granted.
