微力素对肉鸡保健增重及免疫效果的影响

本试验旨在研究植物提取发酵产物-微力素对AA肉仔鸡进行预防肠道疾病、增重及免疫效果的试验。结果表明,在实际养殖条件下使用微力素可以显著提高肉鸡的增重,改善饲料报酬,从而提高经济效益。同时,降低40%的死亡率,其作用机制可能是微力素对致病性的大肠杆菌、沙门氏菌、魏氏梭菌等肠道致病菌有抑制或杀死作用。研究认为,微力素可以保障动物肠道健康和预防下痢及增强免疫等效果。

Effect of Dy addition on microstructure and mechanical properties of Mg-4Y-3Nd-0.4Zr alloy

Minor Dy element was added into a Mg?4Y?3Nd?0.4Zr alloy,and its effects on the microstructure and the mechanicalproperties at elevated temperatures were investigated.Scanning electron microscope(SEM)and transmission electron microscope(TEM)were used to observe the microstructures.The results indicated that the as-cast eutectic and isolated cuboid-shaped Mg?REphases were Mg5RE and Mg3RE17,respectively,and distributed mainly along grain boundaries.After a solution treatment,theeutectic Mg5RE phases were dissolved into the matrix,whereas the Mg3RE17compound still remained.After peak aging,fineMg?RE phases were precipitated homogeneously within the matrix of the alloys containing Dy.Dy addition can result in asignificant improvement in the tensile strength at both room and elevated temperatures,and a slight decrease in the elongation.

Effects of minor B addition on microstructure and properties of AlCoFeNi eutectic high-entropy alloy

The simultaneous strengthening of mechanical and magnetic properties is an ideal fabrication strategy for soft-magnetic materials. A non-equiatomic Al19Co20Fe20Ni41 eutectic high-entropy alloy was prepared to investigate the alloying effect of B on the microstructure evolution, phase formation, mechanical and soft-magnetic properties. With the increase in B content, the microstructures of(Al19Co20Fe20Ni41)100-xBx alloys transformed from the initial lamellar eutectic structure(x=0) to the divorced eutectic structure(x>0.6). Fine borides precipitated in the intergranular phase(x≥0.6). The hardness of alloys increased from HV 328.66 to HV 436.34 and the compression mechanical performance displayed a transition from plastic material to brittle material. The Al19Co20Fe20Ni41 alloy possesses good soft-magnetic properties, and the minor B addition has little effect on it. Increasing the resistivity can effectively reduce the eddy current loss when used as a soft-magnetic material.

Differences of Physiological and Biochemical Indexes of Upper Fresh Leaves and Post-growth Roots in Different Quality Stages

In order to explore the physiological and biochemical characteristics of fresh upper leaves and roots of different qualities of tobacco, the malonaldehyde （MDA）, superoxide dismutase （SOD） activity, chlorophyllase activity, amylase activity, medium trace element content, chemical component content, root fresh weight, dry weight and activity in the normal tobacco leaves, tobacco leaves rich in nutrients and premature grey tobacco leaves were studied. The results showed that compared with the normal tobacco leaves, the root fresh weight, dry weight and activity in the premature grey tobacco leaves decreased by 41.22%, 14.44% and 60.29% respectively, while malonaldehyde content increased by 34.82%, and chlorophyllase, α-amylase, β-amylase and SOD activity declined by 89.55%, 65.71%, 71.26% and 37.25% respectively. Chlorophyllase, co-amylase and 13-amylase activity in the tobacco leaves rich in nutrients decreased by 58.76%, 36.19% and 41.93% respectively. The content of medium trace elements in the tobacco leaves rich in nutrients and premature grey tobacco leaves was lower than that of the normal tobacco leaves. Starch, total sugar, reducing sugar and potassium content in the normal tobacco leaves were higher than that of the tobacco leaves rich in nutrients and premature grey tobacco leaves.

Effect of Nd addition on microstructure and tensile properties of laser additive manufactured TC11 titanium alloy

Single-layer and multilayer laser additive manufacturing(LAM)for TC11 alloy with different Nd additions was conducted and the effect of Nd addition on microstructure and properties was studied.With the addition of Nd,the aspect ratio of melting pools of single-layer specimens increases and the columnar-to-equiaxed transition occurs.The originalβgrain size andαplate width of TC11−1.0Nd are significantly reduced compared with those of pure TC11 specimens.It is proposed that the evenly distributed fine Nd_(2)O_(3) precipitates of about 1.51μm are formed preferentially during rapid solidification of melting pool,and they serve as heterogeneous nucleation particles to refine the microstructure in the subsequent solidification and solid-state phase transformation.Due to the multiple effects of Nd on the microstructure,the ultimate tensile strength of TC11−1.0Nd increases,while the yield strength,ductility and microhardness decrease compared with those of pure TC11.

Protective effect of heme oxygenase-1 on Wistar rats with heart failure through the inhibition of inflammation and amelioration of intestinal micro- circulation

Background Myocardial infarction （MI） has likely contributed to the increased prevalence of heart failure （HF）. As a result of re- duced cardiac function, splanchnic blood flow decreases, causing ischemia in villi and damage to the intestinal barrier. The induction of heme oxygenase-1 （HO-1） could prevent, or lessen the effects of stress and inflammation. Thus, the effect and mechanism thereof of HO-1 on the intestines of rats with HF was investigated. Methods Male Wistar rats with heart failure through ligation of the left coronary artery were identified with an left ventricular ejection fraction of 〈 45% through echocardiography and then divided into various experimental groups based on the type of peritoneal injection they received [MI： saline; MI ＋ Cobalt protoporphyrin （CoPP）： CoPP solution; and MI ＋ Tin mesoporphyrin IX dichloride （SnMP）： SnMP solution]. The control group was comprised of rats without coronary ligation. Echocardiogra- phy was performed before ligation for a baseline and eight weeks after ligation in order to evaluate the cardiac function of the rats. The bac- terial translocation （BT） incidence, mesenteric microcirculation, amount of endotoxins in the vein serum, ileum levels of HO- 1, carbon oxide （CO）, nitric oxide （NO）, intedeuldn （IL）-10, turnour necrosis factor-et （TNF-ct）, and the ileum morphology were determined eight weeks after the operation. Results The rats receiving MI ＋ CoPP injections exhibited a recovery in cardiac function, an amelioration of mesenteric microcirculation and change in morphology, a lower BT incidence, a reduction in serum and ileac NO and TNF-ct levels, and an elevation in ileac HO-1, CO, and interleukin-10 （[L-10） levels compared to the MI group （P 〈 0.05）. The rats that received the MI ＋ SnMP injections exhibited results inverse to the MI （P 〈 0.05） group. Conclusions HO-1 exerted a protective effect on the intestines of rats with HF by inhibiting the inflammation and amelioration of microcirculation through the CO pathway. This protective effect could be independent from the recovery of cardiac function.

Vertical variation of trace elements and its relation to the water-bearing capacity of Ordovician strata,in Datun coal field

We tested for fourteen trace elements in samples collected from the Ordovician strata in Datun coal field. The vertical concentration variation of these trace dements is reported. The relationship of the variation to the water-bearing capacity of the Ordovician strata is discussed. The minimum concentration of eleven （of 14 total） trace elements appears in the lower Majiagou formation. The maximum concentrations mainly appear in the Badou and Jiawang formations： eight maxima are located in Badou and four more are in Jiawang. The study of karst development and the water-bearing capacity of Ordovician strata shows that karst is well developed in the Majiagou formation and there is a consequent high water-bearing capacity in this formation： Badou and Jiawang formations are contrary to this situation. The results illustrate that the minimum concentrations of most trace elements within certain Ordovician formations can be taken as strong evidence for the existence of a well developed karst and a high water-bearing capacity.

Effect of elements Zn, Sn and In on microstructures and performances of AZ91 alloy

A new magnesium alloy plate added elements Zn, Sn and In was manufactured by twin-roll continuous casting method to improve the precipitation of AZ91 alloy. The effects of elements addition and casting method on microstructure and mechanical properties of the Mg-Zn-In-Sn alloys were investigated by optical microscopy (OM), transmission electron microscopy (TEM), electron probe micro-analysis (EPMA), X-ray diffractometry (XRD) and energy dispersion spectrograph (EDS). The results show that the Mg-Zn-In-Sn alloy has higher tensile strength and better corrosion protection than the AZ91 alloy. The outstanding precipitation strengthening effect of the alloy is attributed to the small grain size and the hard precipitates between the grain boundaries.

Characteristics of the genetic mineralogy of pyrite and its significance for prospecting in the Denggezhuang gold deposit,Jiaodong Peninsula,China

This paper reports the variation rules for the typomorphic parameters of the pyrite and the gold enrichment rules of the Denggezhuang quartz vein gold deposit at a large-depth scale, providing the mineral signs for deep prospecting prediction through detailed study of the characteristics of crystal＇ habits, chemical composition, the thermoelectricity of pyrites, and min- eralogical mapping. This paper primarily discusses the correlation between the mineralization intensity and the space-time evolution of the mineralogical parameters, clarifies the physicochemical conditions during gold mineralization, and provides information useful for deep mineralization prediction. We demonstrate that the crystal habits of the pyrites are very complex, primarily occurring as （ 100）, （210）, and their combinate form. （210） and （ 100）＋（210） have positive correlations with gold mineralization, and （ 100）＋（210） therefore can be useful for locating rich ore segments. The composition of pyrites is charac- teristically poor in S and rich in As. Their typical trace elements are composed of Mo, As, Pb, Cu, Bi, Zn, Au, Co, Se, Sb, Ag, Ni, Cr, and Te. The average contents of trace elements in pyrites from various stages show that the crystallizing temperature gradually decreased from an early stage to the metallogenic episodes. The precipitation and accumulation of Au and Ag occur primarily in the quartz-pyrite stage （III） and the polymetal minerals stage （IV）. The occurrence rate of P-type pyrites （P（%）） is 83.52%. There is a larger dispersion of the thermoelectrical coefficient of pyrite （a） in the Denggezhuang gold deposit than in other deposits in the Jiaodong Peninsula. The electrical conductivity assemblage of pyrites from I to V is characterized by P〉N〉P〉N〉P〉〉N〉P〉〉N〉P〉N, which is usually considered beneficial for mineralization. The relative contents of As＋Sb＋Se＋Te and Co＋Ni are closely correlated to P-type and N-type average values and their occurrence rates. According to the crystallizing temperature of pyrite, the mineralization intensity, and the denudation degree, the mineralization temperature of the Denggezhuang gold deposit is in the range of 150-322~C and is of a medium-low temperature. The orebody has already become denuded to the top-middle of the orebody, and the size of the orebody is larger than 900 m. Based on the vertical zon- ing of the thermoelectrical coefficients of pyrites and P-type pyrite mapping, it is suggested that the segment between -425 and -800 m may have exploration potential to the northeast of line 94 of the No. I2.2 orebody.

Experimental and model comparisons of H_2O_2 assisted UV photodegradation of Microcystin-LR in simulated drinking water

The degradation of Microcystin-LR (MC-LR) in water by hydrogen peroxide assisted ultraviolet (UV/H2O2) process was investigated in this paper. The UV/H2O2 process appeared to be effective in removal of the MC-LR. MC-LR decomposition was primarily ascribed to production of strong and nonselective oxidant-hydroxyl radicals within the system. The intensity of UV radiation, initial concentration of MC-LR, MC-LR purity, dosages of H2O2, the initial solution pH, and anions present in water, to some extent, influenced the degradation rate of MC-LR. A modified pseudo-first-order kinetic model was developed to predict the removal efficiency under different experimental conditions.

Polydopamine-assisted functionalization of heparin and vancomycin onto microarc-oxidized 3D printed porous Ti6Al4V for improved hemocompatibility,osteogenic and anti-infection potencies

Enhanced antiinfection activities, improved hemocompatibility and osteo-compatibility, and reinforced osseointegration are among the most important considerations in designing multifunctional orthopedic biomaterials.Hereby, anti-infective and osteogenic multifunctional 3 D printed porous Ti6 Al4 V implant with excellent hemocompatibility was successfully designed and fabricated. In brief, osteogenic micro-arc oxidation（MAO） coatings with micro/nanoscale porous topography were generated in situ on3 D printed Ti6 Al4 V scaffolds, on which heparin and vancomycin were easily immobilized. The surface microstructure,morphology, and chemical compositions were characterized employing scanning electron microscopy（SEM）, X-ray photoelectron spectroscopy（XPS） and Fourier transform infrared spectroscopy（FTIR）. High loading capacity and sustained vancomycin release profiles were revealed using high performance liquid chromatography（HPLC）. Favorable antibacterial and antibiofilm performances against pathogenic Staphylococcus aureus（S. aureus） were validated in vitro through microbial viability assays, Live/Dead bacterial staining, and crystal violet staining. Human mesenchymal stem cells（h MSCs） were seeded on the scaffolds and their proliferation and viability were assessed using Cell Counting Kit and Live/Dead cell viability kit. Further, osteoblastic differentiation abilities were evaluated using alkaline phosphatase（ALP） activity as a hall marker. Additionally, the improved hemocompatibility of the heparinized scaffolds was confirmed by activated partial thromboplastin time（APTT）, prothrombin time（PT） and thrombin time（TT）. Overall, our results show that the surface-modified 3 D printed porous Ti6 Al4 V possesses balanced antibacterial and osteogenic functions while exhibiting extra anticlotting effects, boding well for future application in customized functional reconstruction of intricate bone defects.

Mechanical properties of individual core-shell-structured Sn O2@C nanofibers investigated by atomic force microscopy and finite element method

Although SnO_2-based nanomaterials used to be considered as being extraordinarily versatile for application to nanosensors,microelectronic devices, lithium-ion batteries, supercapacitors and other devices, the functionalities of SnO_2-based nanomaterials are severely limited by their intrinsic vulnerabilities. Facile electrospinning was used to prepare SnO_2 nanofibers coated with a protective carbon layer. The mechanical properties of individual core-shell-structured SnO_2@C nanofibers were investigated by atomic force microscopy and the finite element method. The elastic moduli of the carbon-coated SnO_2 nanofibers remarkably increased, suggesting that coating SnO_2 nanofibers with carbon could be an effective method of improving their mechanical properties.