皮肤成纤维细胞制备微构组织的聚团过程及数值模拟

微构组织的聚团尺寸影响其内部的细胞活性及体外构建大型工程化组织。采用转瓶系统,考察了皮肤成纤维细胞(human fibroblast,HF)接种密度、微载体浓度和添加抗坏血酸磷酸酯盐(L-ascorbic acid 2-phosphate,简称Vc)对微构组织形成及聚团尺寸的影响,并建立了微构组织聚团的数学模型。结果表明,微构组织的聚团过程可分为迟滞期、突跃期和稳定期,随着细胞接种密度、微载体浓度提高以及Vc的添加,微构组织的平均聚团尺寸增大,建立的数学模型能够模拟不同操作条件下微构组织形成的过程和聚团尺寸,模拟结果与实测值基本相符,为进一步调控微构组织聚团和大型工程化组织制备奠定基础。

利用大孔微载体体外制备工程化组织

组织工程从诞生至今已有二十年的历史,微载体在组织工程领域的应用研究近年来才日趋升温。利用大孔微载体Cytopore体外构建工程化微构组织,并基于其聚团特性,进行灌注再装配大组织的尝试。结果20 d内微构组织达最高细胞密度16.4×10~7cells/cm^3;32 d后,所形成的微构组织整体均质性好、活性高、基质生成丰富;培养后期微构组织发生明显聚团,经灌注再装配得到细胞和基质分布均匀的厘米级(12mm×6mm)大组织。说明利用大孔微载体构建工程化组织是一种行之有效、富有潜力的体外组织构建方案,有望构建尺寸≥5 mm、细胞和基质分布均匀的大组织。为体外组织构建提供新的思路。

Effect of forging on the microstructure and texture of a high Nb containing γ-TiAl alloy

The effect of forging on the microstructure and texture evolution of a high Nb containing Ti-45Al-7Nb-0.3W(at.%)alloy was investigated by X-ray diffractometer(XRD),scanning electron microscopy(SEM),and transmission electron microscopy(TEM).The results show that the as-cast alloy is mainly composed of α_(2)/γ lamellar colonies with a mean size of 70μm,but the hot-forged pancake displays a near duplex microstructure(DP).Kinking and bending of lamellar colonies,deformation twinning and dynamic recrystallization(DRX)occur during hot forging.Meanwhile,dense dislocations in theβphase after forging suggest that the high-temperature β phase with a disordered structure is favorable for improving the hot-workability of the alloy.Unlike the common TiAl casting texture,the solidification process of the investigated as-cast alloy with high Nb content is completely via the β phase region,resulting in the formation of a<110>γ fiber texture where the<110>γ aligns parallel to the heat-flow direction.In comparison,the relatively strong<001>and weak<302>texture components in the as-forged alloy are attributed to the deformation twinning.After annealing,static recrystallization occurs at the twin boundary and intersections,which weakens the deformation texture.

Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing

In this work,a novel type of short-process deformation technology of Mg alloys,bifurcation-equal channel angular pressing(B-ECAP),was proposed to refine grain and improve the basal texture.The cylindrical billets were first compressed into the die cavity,then sequentially flowed downward through a 90°corner and two 120°shear steps.The total strain of B-ECAP process could reach 3.924 in a single pass.The results of microstructure observation showed that DRX occurred at upsetting process in the die cavity and completed at position D.The grains were refined to 6.3μm at being extruded at 300℃ and grew obviously with the extrusion temperature increase.The shear tress induced by 900 corner and two 120°shear steps resulted in the basal poles of most grains tilted to extrusion direction(ED)by±25°.Compared with the original billets,the extruded sheets exhibited higher yield strengths(YS),which was mainly attributed to the grain refinement.The higher Schmid factor caused by ED-tilt texture resulted in a fracture elongation(FE)more than that of the original bar in ED,while was equivalent to that in transverse direction(TD).As the extrusion temperature increased,the variation of UTS and YS in ED and TD decreased gradually without ductility obviously decrease.

Microstructure and texture of commercially pure titanium in cold deep drawing

The development of microstructure and texture during cold deep drawing of commercially pure titanium（CP-Ti） was investigated.Three parts,stretching region,drawing region and flange region,were sequentially formed in the deep drawing process of the hemispheric surface part,with reference to deformation modes and strain regimes.Results show that the plastic strain is accommodated by dislocation slip and deformation twinning in the whole deep drawing process.The texture of the CP-Ti sheet and its drawn part consists of rolling texture component and recrystallization texture component.The intensity and type of the initial texture varied during the drawing process are related to the production of deformation twinning and dislocation slip.Twinning weakens the initial texture by randomizing the orientations of crystals,especially for the recrystallization texture.The recrystallization texture in the drawing region disappears due to the significant forming of twinning.Furthermore,over drawing would result in the predominance of dislocation slip and the texture is strengthened.

Effects of stress state on texture and microstructure in cold drawing-bulging of CP-Ti sheet

Three different stress states of the combination of tensile（t） stress and compressive（c） stress,t t,t c and t c c,exist in the deformed commercially pure titanium（CP-Ti） sheet during cold drawing-bulging.The textures and microstructures in the different stress state regions were investigated by means of XRD and TEM analysis.Similar development of texture and microstructure is achieved with less thickness strain under multiaxial stresses in drawing-bulging than in cold rolling.The results show that texture and microstructure are much sensitive to multiaxial stresses.Twinning is more easily activated under compressive stress than tensile stress.Prism a slip is heavily affected by tensile stress,resulting in a remarkable change of the intensity of（0°,35°,0°） texture,while pyramidal c＋a slip,forming（20°,35°,30°） texture,weakens with the increase of thickness strain in spite of stress state.

Microstructure of TA2/TA15 graded structural material by laser additive manufacturing process

TA2/TA15 graded structural material（GSM） was fabricated by the laser additive manufacturing（LAM） process. The chemical composition, microstructure and micro-hardness of the as-deposited GSM were investigated. The results show that the TA2 part of exhibiting near-equiaxed grains was Widmanst？tten α-laths microstructure. The TA15 part containing large columnar grains was fine basket-weave microstructure. The graded zone was divided into four deposited layers with 3000 μm in thickness. As the distance from the TA2 part increases, the alloy element contents and the β phase volume fraction increase, the α phase volume fraction decreases and the microstructure shows the evolution from Widmanst？tten α-laths to basket-weave α-laths gradually. The micro-hardness increases from the TA2 part to the TA15 part due to the solid solution strengthening and grain boundary strengthening.

Effect of pre-deformation on aging creep of Al-Li-S4 alloy and its constitutive modeling

A set of uniaxial tensile creep tests at different pre-deformations, aging temperatures and stress levels were carried out for Al-Li-S4 alloy, and the creep behavior and the effects of pre-deformation on mechanical properties and microstructures were determined under basic thermodynamics conditions of aging forming. The results show that pre-deformation shortens the time of primary creep and raises the second steady-state creep rate. Then, the total creep strain is greater, but in the range of test parameters it is still smaller than that without pre-deformation. In addition, transmission electron microscopy（TEM） observation shows that pre-deformation promotes the formation of T1 phase and θ′ phase and makes them distribute more dispersively, while inhibits the generation of δ′ phase, which leads to the improvement of mechanical properties of the alloy. A unified constitutive model reflecting the effects of aging mechanism, stress levels and different pre-deformations was established. The fitting results agree with the experimental data well.

Influence of microstructure and texture on formability of AZ31B magnesium alloy sheets

The effect of the repeated unidirectional bending （RUB） process and annealing on the formability of magnesium alloy sheets was investigated. The RUB process and annealing treatments produce two effects on microstructure： grain coarsening and weakening of the texture. The sheet that underwent RUB and was annealed at 300 ℃exhibits the best formability owing to the reduction of the （0002） basal texture intensity, which results in low yield strength, large fracture elongation, small Lankford value （r-value） and large strain hardening exponent （n-value）. Compared with the as-received sheet, the coarse-grain sheet produced by RUB and annealing at 400 ℃ exhibits lower tensile properties but higher formability. The phenomenon is because the deformation twin enhanced by grain coarsening can accommodate the strain of thickness.

Grain structure and microtexture evolution during superplastic deformation of 5A90 Al-Li alloy

The microstructural evolution of banded 5A90 A1-Li alloy during superplastic deformation at 475℃ with an initial strain rate of 8× 10^-4 S^-1 was studied using EBSD technique. The results showed that, before deformation, the grain shape appeared to be banded, the most grain boundaries belonged to low-angle boundaries, and the initial sheet had a dominate of { 110}（112） brass texture. During deformation, there were grain growth, grain shape change, misorientation increasing and textural weakening. The fraction of high-angle boundaries increased rapidly once the flow stress reached the peak value. Corresponding deformation mechanism for various stages of deformation was suggested. Dislocation activity was the dominant mechanism in the first stage, then dynamic recrystallization occurred, and grain rotation was expected as an accommodation for grain boundary sliding （GBS）. At large strains, GBS was the main mechanism.

Microstructure evolution of alumina dispersion strengthened copper alloy deformed under different conditions

Microstructure and texture evolution of Cu-0.23%Al2O3 dispersion strengthened copper alloy, deformed at room temperature or cryogenic temperature, were investigated. The main textures in hot-extruded specimen were Brass {011} 〈211〉 and Cube {100} 〈100〉. Textures of Brass {011} 〈211〉 and Goss {011} 〈100〉 were observed in specimen after deformation at room temperature; while textures of Brass {011} 〈211〉, Goss {011} 〈100〉 and S {123} 〈634〉 were detected after deformation at cryogenic temperature. It is believed that the additional Al2O3 nanoparticles can result in dislocation pinning effect, which can further lead to the suppression of dislocations cross-slip. While in the specimen deformed at cryogenic temperature, both pinning effect and cryogenic temperature are responsible for the formation of Brass, Goss and S textures.

Morphology and chemical composition of γ/γ' phases in Re-containing Ni-based single crystal superalloy during two-step aging

The γ/γ＇ microstructure of a Re-containing Ni-based single crystal super alloy after a two-step aging was studied using scanning electron microscopy （SEM）,transmission electron microscopy （TEM） and scanning transmission electron microscopy （STEM）.The crystals were grown by the floating zone （FZ） method.Both cuboidal and spherical γ＇ precipitates were formed after a two-step aging.The size of the cuboidal γ＇ phases first increased and then decreased with the extension of the second-step aging time.Re,Co and Cr strongly concentrated in the γ phase whereas Ni and Al enriched in the γ＇ phase.Thermodynamic calculation by JMatPro was performed to explain the experimental observations.

Influence of thermomechanical processing on microstructure,texture evolution and mechanical properties of Al-Mg-Si-Cu alloy sheets

Influence of thermomechanical processing on the microstructure, texture evolution and mechanical properties of A1-Mg-Si-Cu alloy sheets was studied systematically. The quite weak mechanical properties anisotropy was obtained in the alloy sheet through thermomechanical processing optimizing. The highly elongated microstmcture is the main structure for the hot or cold-rolled alloy sheets. H {001 } （110） and E { 111 } （110） are the main texture components in the surface layer of hot-rolled sheet, while ]/-fibre is dominant in quarter and center layers. Compared with the hot-rolled sheet, the intensities offl-fibre components are higher after the first cold rolling, but H {001 }（110） component in the surface layer decreases greatly. Almost no deformation texatre can be observed after intermediate annealing. And fl-fibre becomes the main texture again after the final cold rolling. With the reduction of the thickness, the through-thickness texture gradients become much weaker. The through-thickness recrystallization texture in the solution treated sample only has cubeyD {001 }（310） component. The relationship among thermomechanical processing, microstructure, texture and mechanical orouerties was analyzed.

Compressive anisotropy of extruded Mg-Dy-Zn alloy sheet

Compressive anisotropy of extruded Mg-2Dy-0.5Zn （mole fraction, %） alloy sheet was investigated. The alloy sheet was mainly composed ofα-Mg, （Mg, Zn）xDy phase and a large number of long period stacking ordered （LPSO） phases distributed along the extrusion direction. The compressive experimental results show that the alloy sheet exhibits an obvious compressive anisotropy. The compressive strength of the specimen in the extrusion direction （ED） is higher than those of the specimens in the transverse direction （TD） and 45° inclined to the extrusion direction. The compressive yield strength （CYS）, ultimate compressive strength （UCS） and compressive strain of the specimen in the ED are 274.65 MPa, 518.94 MPa and 12.93%, respectively. The compressive anisotropy is mainly attributed to the distribution of LPSO phase and formation of〈10 10〉//ED fiber texture in the deformed grains.

Microstructure and mechanical properties of TiAl-based alloy prepared by double mechanical milling and spark plasma sintering

A fine-grained TiAl alloy with a composition of Ti-45Al-2Cr-2Nb-1B-0.5Ta-0.225Y （mole fraction, %） was prepared by double mechanical milling（DMM） and spark plasma sintering（SPS）. The relationship among sintering temperature, microstructure and mechanical properties was studied. The results show that the morphology of double mechanical milled powder is regular with size in the range of 20-40 μm and mainly composed of TiAl and Ti3Al phases. The main phase TiAl and few phases Ti3Al, Ti2Al and TiB2 were observed in the SPSed alloys. For samples sintered at 900 ℃ the equiaxed crystal grain microstructure is achieved with size in the range of 100-200 nm. With increasing the SPS temperature from 900 ℃to 1000 ℃ the size of equiaxed crystal grain obviously increases, the microhardness decreases from HV658 to HV616, and the bending strength decreases from 781 MPa to 652 MPa. In the meantime, the compression fracture strength also decreases from 2769 MPa to 2669 MPa, and the strain to fracture in compression increases from 11.69% to 17.76%. On the base of analysis of fractographies, it shows that the compression fracture transform of the SPSed alloys is intergranular rupture.

Cytological Studies on the Development of Sieve Element and Floral Nectary Tissue in Arabidopsis thaliana

Ultrastructural changes in the sieve element and dense cells of nectariferous tissue during the development of floral nectary in Arabidopsis thaliana L. were investigated with transmission electron microscopy. Samples were prepared with high pressure freezing and freeze substitution techniques. The ultrastructure of dense cell was similar to that of sieve element at its early developmental stage. With the concurrent agglutination of chromatin in the nucleus, the abnormal location of organelles and the high density of cytoplasm, the ultrastructural characteristics in die dense cells of the nectariferous tissue and in the sieve element are matched with those of the programmed cell death in animal and plant reported in recent years. The disorganization of nucleus and most organelles in the differentiation of sieve elements and dense cells is closely associated with the transportation and modification of pre-nectar and the transference of nectar. This suggests that the cytological changes in sieve element and nectariferous tissue are closely associated with the nectary functional activities.

Microstructural evolution and delayed hydride cracking of FSW-AZ31 magnesium alloy during SSRT

Evolution of microstructure including texture and fractography in a friction-stir welded（FSW） AZ31 magnesium alloy was investigated. The texture was measured using a neutron diffractometer. The microstructure and fractography of stress corrosion cracking（SCC） samples were observed by optical and scanning electron microscopy, respectively. An X-ray diffraction study was carried out on the fractured surfaces of the SCC specimens. The results indicated that a strong basal fiber was formed on the base material, whereas the grains in the stir zone were reoriented with their most basal planes tilted 25 o to the welding direction. Feather-like twins and hydride formed under slow strain rate tensile（SSRT） stress in air and aggressive solutions, respectively. Transgranular cracks propagated and finally failed on the retreating side in the solution. The hydride phase confirmed to sit on the fracture surface demonstrated the delayed hydride cracking（DHC） mechanism of the alloy.

Hot deformation behaviors of 35% SiC_p/2024Al metal matrix composites

The hot deformation behaviors of 35%SiCp/2024 aluminum alloy composites were studied by hot compression tests using Gleeble-1500D thermo-mechanical simulator at temperatures ranging from 350 to 500 °C under strain rates of 0.01-10 s-1. The true stress-true strain curves were obtained in the tests. Constitutive equation and processing map were established. The results show that the flow stress decreases with the increase of deformation temperature at a constant strain rate, and increases with the increase of strain rate at constant temperature, indicating that composite is a positive strain rate sensitive material. The flow stress behavior of composite during hot compression deformation can be represented by a Zener-Hollomon parameter in the hyperbolic sine form. Its activation energy for hot deformation Q is 225.4 kJ/mol. To demonstrate the potential workability, the stable zones and the instability zones in the processing map were identified and verified through micrographs. Considering processing map and microstructure, the hot deformation should be carried out at the temperature of 500 °C and the strain rate of 0.1-1 s-1.

Effects of Weak Light on the Ultrastructural Variations of Phloem Tissues in Source Leaves of Three-Year-Old Nectarine Trees(Prunus persica L.var. nectarina Ait.)

Leaves from three_year_old solar greenhouse nectarine trees ( Prunus persica L. var. nectarina Ait. “Zao Hong Yan”) were used as materials in this study. It was the first time that the ultrastructural characteristics of phloem tissues of source leaves were observed and compared in normal and weak light intensities using the transmission electron microscopy. Results showed that the average diameters of companion cells (CC) and sieve elements (SE) of all kinds of veins were bigger in normal than that in weak light intensity, indicating that light could influence the cell development and growth. Dense cytoplasm with abundant mitochondria, endoplasmic reticulums, multivesicular bodies, vesicles and plastids were observed in normal light intensity. On the contrary, CC with small vacuolar structures and few mitochondrias, endoplasmic reticulums were shown in weak light. Misalignment of grana thylakoid margins of nectarine leaves also was seen in weak light. The sieve pores of SEs were obstructed in weak light. Chloroplasts with numerous starch grains and few mitochondrias were noticed in the mesophyll cell (MES) surrounding the bundle sheath in weak light. The storage of starch grains appeared to result from an unbalance between photosynthate production and export of photosynthates. This observation provided a strong support to the point that most leaves export the most of assimilates in the light time. Plasmodesmal densities between SE/CC, CC/PP (phloem parenchyma cell), PP/PP and PP/BSC (bundle_sheath cell) decreased in weak light. Plasmodesmata were observed between CC/SE (NS) (nacreous_walled sieve element), PP/BSC in branch veins in normal light intensity, but not in weak light. Thus apoplasmic pathway may be the main mode of transport of assimilates in weak light, however symplasmic pathway may be the main mode of transport of assimilates in normal light intensity. These results demonstrated that the solar greenhouse nectarine trees could be adapted to the weak light via the ultrastructure variation of phloem tissues of the source leaves.

Enhanced ductility and reduced asymmetry of Mg-2Al-1Zn alloy plate processed by torsion and annealing

The ductility and plastic asymmetry of an as-annealed magnesium alloy plate were studied in compression through combined process of torsion and subsequent annealing by optical microscope and EBSD. The yield strength（YS） and ultimate compression strength（UCS） as well as the compression ductility（CD） were simultaneously raised by prior torsion at room temperature. The CD was further enhanced by subsequent annealing. Also, the torqued sample followed by annealing experienced a rising CD with the increase in prior strain, leading to the maximum true strain of 0.279, which is twice that of the as-annealed original one. The sample showed a largely reduced tension-compression yield asymmetry by subjecting to pre-torsion alone or combined with a subsequent annealing. The enhanced ductility and reduced asymmetry are attributed to the development of a gradient microstructure with refined grains, and also randomization of the weakened texture due to torsion and subsequent annealing.