In order to prepare high-performance Mo with fine and homogeneous microstructure to meet the demand of high-technology applications such as metallurgical,mechanical,national defense,aerospace and electronics applicati...In order to prepare high-performance Mo with fine and homogeneous microstructure to meet the demand of high-technology applications such as metallurgical,mechanical,national defense,aerospace and electronics applications,the microwave sintering process and densification mechanism of Mo nanopowder were studied.In this experiment,Mo nanopowder and micropowder were used for conventional sintering and microwave sintering at different sintering temperatures and sintering time,respectively.The results showed that with the increase in the sintering temperature,the increase rates of the relative density and hardness increased rapidly at first and then slowed down.The relative density rapidly reached 95%,followed by a small change.Mo nanopowder with a relative density of 98.03% and average grain size of 3.6 μm was prepared by microwave sintering at 1873 K for30 min.According to the analysis of the sintering kinetics,its densification is attributed to the combination of volumetric diffusion and grain boundary diffusion mechanisms.The calculated sintering activation energy of Mo nanopowder was 203.65 kJ/mol,which was considerably lower than that in the conventional sintering,suggesting that the microwave sintering was beneficial to the enhancement in the atom diffusion and densification for the powder.The results confirm that the microwave sintering is a promising method to economically prepare molybdenum with high properties.展开更多
Photocatalytic activity of doped polyaniline nanopowders with different molar ratio of An/O （aniline^oxidizer） has been studied in the process of photocatalytic decolorization of aqueous solutions of methylene blue....Photocatalytic activity of doped polyaniline nanopowders with different molar ratio of An/O （aniline^oxidizer） has been studied in the process of photocatalytic decolorization of aqueous solutions of methylene blue. By means of scanning electron microscopy and low-temperature N2 adsorption method, it was found that doped PANI （polyaniline） nanopowders have the particles size of 30-50 nm with the specific surface area of 20-35 m2.g＂~. It was found that PANI photocatalytic activity essentially depends on molar ratio of An/O and adsorption interactions between the dye molecules and catalytic active centers on PANI surface and these interactions are greatly affected by pH of the solution 9.2. An optimum of the synergetic effect is found for an initial molar ratio of aniline to oxidizer equal to 0.8.展开更多
A few-layered MoS2-C composite material is studied as a supporting material for silicon nanopowder. Microspheres of the few-layered MoS2-C composite embedded with 30 wt.% Si nanopowder are prepared by one-pot spray py...A few-layered MoS2-C composite material is studied as a supporting material for silicon nanopowder. Microspheres of the few-layered MoS2-C composite embedded with 30 wt.% Si nanopowder are prepared by one-pot spray pyrolysis. The Si nanopowder particles with high capacity are completely surrounded by the few-layered MoS2-C composite matrix. The discharge capacities of the MoS2-C composite microspheres with and without 30 wt.% Si nanopowder after 100 cycles are 1,020 and 718 mAh·g^-1 at a current density of 1,000 mA·g^-1 respectively. The spherical morphology of the MoS2-C composite microspheres embedded with Si nanopowder is preserved even after 100 cycles because of their high structural stability during cycling. The MoS2-C composite layer prevents the formation of unstable solid-electrolyte interface （SEI） layers on the Si nanopowder. Furthermore, as the MoS2-C composite matrix exhibits high capacity and excellent cycling performance, these characteristics are also reflected in the MoS2-C composite microspheres embedded with 30 wt.% Si nanopowder.展开更多
In this work, strength assessments and percentage of water absorption of self compacting concrete containing ground granulated blast furnace slag （GGBFS） and A1203 nanoparticles as binder have been investigated. Por...In this work, strength assessments and percentage of water absorption of self compacting concrete containing ground granulated blast furnace slag （GGBFS） and A1203 nanoparticles as binder have been investigated. Portland cement was replaced by different amounts of GGBFS and the properties of concrete specimens were investigated. Although it negatively impacts the physical and mechanical properties of concrete at early ages of curing, GGBFS was found to improve the physical and mechanical properties of concrete up to 45 wt% at later ages. A1203 nanoparticles with the average particle size of 15 nm were added partially to concrete with the optimum content of GGBFS and physical and mechanical properties of the specimens were measured. A1203 nanoparticle as a partial replacement of cement up to 3.0 wt% could accelerate C-S-H gel formation as a result of increased crystalline Ca（OH）2 amount at the early ages and hence increase strength and improve the resistance to water permeability of concrete specimens. The increase of the A1203 nanoparticles＇ content by more than 3.0 wt% would cause the reduction of the strength because of the decreased crystalline Ca（OH）2 content required for C-S-H gel formation. Several empirical relationships have been presented to predict flexural and split tensile strength of the specimens by means of the corresponding compressive strength at a certain age of curing. Accelerated peak appearance in conduction calorimetry tests, more weight loss in thermogravimetric analysis and more rapid appearance of the peaks related to hydrated products in X-ray diffraction results, all indicate that A1203 nanoparticles could improve mechanical and physical properties of the concrete specimens.展开更多
基金Project(2017YFB0305601) supported by the National Key R&D Program of ChinaProjects(51874368,51274246) supported by the National Natural Science Foundation of China
文摘In order to prepare high-performance Mo with fine and homogeneous microstructure to meet the demand of high-technology applications such as metallurgical,mechanical,national defense,aerospace and electronics applications,the microwave sintering process and densification mechanism of Mo nanopowder were studied.In this experiment,Mo nanopowder and micropowder were used for conventional sintering and microwave sintering at different sintering temperatures and sintering time,respectively.The results showed that with the increase in the sintering temperature,the increase rates of the relative density and hardness increased rapidly at first and then slowed down.The relative density rapidly reached 95%,followed by a small change.Mo nanopowder with a relative density of 98.03% and average grain size of 3.6 μm was prepared by microwave sintering at 1873 K for30 min.According to the analysis of the sintering kinetics,its densification is attributed to the combination of volumetric diffusion and grain boundary diffusion mechanisms.The calculated sintering activation energy of Mo nanopowder was 203.65 kJ/mol,which was considerably lower than that in the conventional sintering,suggesting that the microwave sintering was beneficial to the enhancement in the atom diffusion and densification for the powder.The results confirm that the microwave sintering is a promising method to economically prepare molybdenum with high properties.
文摘Photocatalytic activity of doped polyaniline nanopowders with different molar ratio of An/O （aniline^oxidizer） has been studied in the process of photocatalytic decolorization of aqueous solutions of methylene blue. By means of scanning electron microscopy and low-temperature N2 adsorption method, it was found that doped PANI （polyaniline） nanopowders have the particles size of 30-50 nm with the specific surface area of 20-35 m2.g＂~. It was found that PANI photocatalytic activity essentially depends on molar ratio of An/O and adsorption interactions between the dye molecules and catalytic active centers on PANI surface and these interactions are greatly affected by pH of the solution 9.2. An optimum of the synergetic effect is found for an initial molar ratio of aniline to oxidizer equal to 0.8.
文摘A few-layered MoS2-C composite material is studied as a supporting material for silicon nanopowder. Microspheres of the few-layered MoS2-C composite embedded with 30 wt.% Si nanopowder are prepared by one-pot spray pyrolysis. The Si nanopowder particles with high capacity are completely surrounded by the few-layered MoS2-C composite matrix. The discharge capacities of the MoS2-C composite microspheres with and without 30 wt.% Si nanopowder after 100 cycles are 1,020 and 718 mAh·g^-1 at a current density of 1,000 mA·g^-1 respectively. The spherical morphology of the MoS2-C composite microspheres embedded with Si nanopowder is preserved even after 100 cycles because of their high structural stability during cycling. The MoS2-C composite layer prevents the formation of unstable solid-electrolyte interface （SEI） layers on the Si nanopowder. Furthermore, as the MoS2-C composite matrix exhibits high capacity and excellent cycling performance, these characteristics are also reflected in the MoS2-C composite microspheres embedded with 30 wt.% Si nanopowder.
文摘In this work, strength assessments and percentage of water absorption of self compacting concrete containing ground granulated blast furnace slag （GGBFS） and A1203 nanoparticles as binder have been investigated. Portland cement was replaced by different amounts of GGBFS and the properties of concrete specimens were investigated. Although it negatively impacts the physical and mechanical properties of concrete at early ages of curing, GGBFS was found to improve the physical and mechanical properties of concrete up to 45 wt% at later ages. A1203 nanoparticles with the average particle size of 15 nm were added partially to concrete with the optimum content of GGBFS and physical and mechanical properties of the specimens were measured. A1203 nanoparticle as a partial replacement of cement up to 3.0 wt% could accelerate C-S-H gel formation as a result of increased crystalline Ca（OH）2 amount at the early ages and hence increase strength and improve the resistance to water permeability of concrete specimens. The increase of the A1203 nanoparticles＇ content by more than 3.0 wt% would cause the reduction of the strength because of the decreased crystalline Ca（OH）2 content required for C-S-H gel formation. Several empirical relationships have been presented to predict flexural and split tensile strength of the specimens by means of the corresponding compressive strength at a certain age of curing. Accelerated peak appearance in conduction calorimetry tests, more weight loss in thermogravimetric analysis and more rapid appearance of the peaks related to hydrated products in X-ray diffraction results, all indicate that A1203 nanoparticles could improve mechanical and physical properties of the concrete specimens.
