The morphologies and formation process of Ni-pool defects in WC?8Ni cemented carbides were studied. The SEM images show that Ni-pool generally has two kinds of morphologies: “island” in isolation and “ring” around...The morphologies and formation process of Ni-pool defects in WC?8Ni cemented carbides were studied. The SEM images show that Ni-pool generally has two kinds of morphologies: “island” in isolation and “ring” around a new phase. In the obtained samples with “ring-like Ni-pool”, WC, Ni and Ni2W4C (η phase) phases were detected in XRD patterns. Combined with SEM, EDX and XRD results, it is found that the phase in the center of the “ring-like Ni-pool” is Ni2W4C (η phase) and the main chemical components of Ni-pool are Ni, W and C. In addition, the relationships among large size Ni (agglomerated) particles, volatile impurities, pores and carbon content vs forming process of the Ni-pool defects for WC?8Ni cemented carbides are also presented and discussed.展开更多
In order to investigate the effects of two mineral admixtures （i. e., fly ash and ground slag）on initial defects existing in concrete microstructures, a high-resolution X-ray micro-CT（ micro-focus computer tomogra...In order to investigate the effects of two mineral admixtures （i. e., fly ash and ground slag）on initial defects existing in concrete microstructures, a high-resolution X-ray micro-CT（ micro-focus computer tomography）is employed to quantitatively analyze the initial defects in four series of highperformance concrete （HPC）specimens with additions of different mineral admixtures. The nigh-resolution 3D images of microstructures and filtered defects are reconstructed by micro- CT software. The size distribution and volume fractions of initial defects are analyzed based on 3D and 2D micro-CT images. The analysis results are verified by experimental results of watersuction tests. The results show that the additions of mineral admixtures in concrete as cementitious materials greatly change the geometrical properties of the microstructures and the spatial features of defects by physical-chemistry actions of these mineral admixtures. This is the major cause of the differences between the mechanical behaviors of HPC with and without mineral admixtures when the water-to-binder ratio and the size distribution of aggregates are constant.展开更多
Mg-Al-Zn alloy thin strips were prepared by vertical twin-roll casting.Effects of Al and Ca on the microstructure and the surface defects of the thin strips were investigated.The results show that with the increase of...Mg-Al-Zn alloy thin strips were prepared by vertical twin-roll casting.Effects of Al and Ca on the microstructure and the surface defects of the thin strips were investigated.The results show that with the increase of Al content,the quantity of surface cracks of the thin strips increases rapidly and their locations are moved to the center of the thin strips.The alloy melts with more than 0.10%Ca(mass fraction)stick on the roller and a poor surface quality of the thin strips appears.With the increase of Al content,the microstructure of the thin strips evolves from singleα-Mg phase,characterized by the uniform and equiaxed recrystallization grains, to the combination of dendriticα-Mg with Al supersaturatedα-Mg.The minor addition of Ca can obviously refine the grains of Mg-3Al-1Zn thin strip because the formation of Al2Ca and the finest grains are obtained by adding 0.08%Ca.展开更多
文摘The morphologies and formation process of Ni-pool defects in WC?8Ni cemented carbides were studied. The SEM images show that Ni-pool generally has two kinds of morphologies: “island” in isolation and “ring” around a new phase. In the obtained samples with “ring-like Ni-pool”, WC, Ni and Ni2W4C (η phase) phases were detected in XRD patterns. Combined with SEM, EDX and XRD results, it is found that the phase in the center of the “ring-like Ni-pool” is Ni2W4C (η phase) and the main chemical components of Ni-pool are Ni, W and C. In addition, the relationships among large size Ni (agglomerated) particles, volatile impurities, pores and carbon content vs forming process of the Ni-pool defects for WC?8Ni cemented carbides are also presented and discussed.
基金The Scholarship Supported by Ministry of Education of China for Research Abroad(No.3037[2006])the Excellent Doctoral Dissertation Foundation of Southeast University (No.YBTJ-0512)the National Basic Research Program of China(973Program)(No.2009CB623203)
文摘In order to investigate the effects of two mineral admixtures （i. e., fly ash and ground slag）on initial defects existing in concrete microstructures, a high-resolution X-ray micro-CT（ micro-focus computer tomography）is employed to quantitatively analyze the initial defects in four series of highperformance concrete （HPC）specimens with additions of different mineral admixtures. The nigh-resolution 3D images of microstructures and filtered defects are reconstructed by micro- CT software. The size distribution and volume fractions of initial defects are analyzed based on 3D and 2D micro-CT images. The analysis results are verified by experimental results of watersuction tests. The results show that the additions of mineral admixtures in concrete as cementitious materials greatly change the geometrical properties of the microstructures and the spatial features of defects by physical-chemistry actions of these mineral admixtures. This is the major cause of the differences between the mechanical behaviors of HPC with and without mineral admixtures when the water-to-binder ratio and the size distribution of aggregates are constant.
基金Project(50604020)supported by the National Natural Science Foundation of ChinaProject(2007CB613706)supported by the National Basic Research Program of China+1 种基金Project(2009AA03Z507)supported by the National High-tech Research and Development Program of ChinaProject(CSTC2008AA4028)supported by Key Program of Chongqing Science and Technology Commission,China
文摘Mg-Al-Zn alloy thin strips were prepared by vertical twin-roll casting.Effects of Al and Ca on the microstructure and the surface defects of the thin strips were investigated.The results show that with the increase of Al content,the quantity of surface cracks of the thin strips increases rapidly and their locations are moved to the center of the thin strips.The alloy melts with more than 0.10%Ca(mass fraction)stick on the roller and a poor surface quality of the thin strips appears.With the increase of Al content,the microstructure of the thin strips evolves from singleα-Mg phase,characterized by the uniform and equiaxed recrystallization grains, to the combination of dendriticα-Mg with Al supersaturatedα-Mg.The minor addition of Ca can obviously refine the grains of Mg-3Al-1Zn thin strip because the formation of Al2Ca and the finest grains are obtained by adding 0.08%Ca.
