The Ti Bw reinforced near-α titanium matrix composite（Ti-5.8 Al-3.4 Zr-4.0 Sn-0.4 Mo-0.4 Nb-0.4 Si-0.06 C） was successfully synthesized by powder metallurgy and hot extrusion route. The effects of solution and agin...The Ti Bw reinforced near-α titanium matrix composite（Ti-5.8 Al-3.4 Zr-4.0 Sn-0.4 Mo-0.4 Nb-0.4 Si-0.06 C） was successfully synthesized by powder metallurgy and hot extrusion route. The effects of solution and aging temperature on the microstructure and high temperature tensile properties of the composite were investigated. The results revealed that the fine transformed β phase can be obtained by the solution treatment at β phase region and aging treatment, no other precipitates were observed. The α2 phase（Ti3 Al） can be acquired when the solution treated at α＋β phase region followed by aging treatment. With increasing the aging temperature from 500 to 700℃ for 5 h, the size of α2 precipitates increases from about 5 to about 30 nm. The Ti Bw are stable without any interfacial reaction during the heat treatments. The high temperature tensile properties show that the composite performed by solution and aging treatment exhibits good strengthening effects. With increasing the aging temperature from 500 to 700℃, the strength of the composite increases at the expense of elongation due to the increment of α2 precipitates.The strength of the composite at 600℃ increases by 17% to 986 MPa after 1000℃/2 h/AC and 700℃/5 h/AC heat treatment.展开更多
In order to meet the progressive requirement for the performance improvement of steel,the author proposed a novel microstructure featured with multi-phase,meta-stable and multi-scale(so-called as M 3).And then,the new...In order to meet the progressive requirement for the performance improvement of steel,the author proposed a novel microstructure featured with multi-phase,meta-stable and multi-scale(so-called as M 3).And then,the new technologies could be developed to process three prototype steels with high performance:the third generation high strength low alloy(HSLA) steels with improved toughness and/or ductility(AKV(40℃)≥200 J and/or A≥20% when Rp0.2 in 800-1000 MPa),the third generation advanced high strength steels(AHSS)(Rm×A≥30 GPa% when Rm from 1000 MPa to 1500 MPa) for automobiles with improved ductility and low cost,and heat resistant martensitic steels with improved creep strength(10000650≥90 MPa).It can be expected that the new technology developed will remarkably improve the safety and reliability of steel products in service for infrastructures,automobiles and fossil power station in the future.展开更多
Based on gradient control of carbon partitioning between martensite and austenite during heat treatment of steels,a stepping-quenching-partitioning(S-Q-P) process is developed for high strength steels.The S-Q-P proces...Based on gradient control of carbon partitioning between martensite and austenite during heat treatment of steels,a stepping-quenching-partitioning(S-Q-P) process is developed for high strength steels.The S-Q-P process involves several quenching processes at progressively lower temperatures between martensite-start(Ms) and martensite-finish(Mf) temperatures,each followed by a partitioning treatment at either the initial quenching temperature or above that temperature.A novel microstructure is designed based on the S-Q-P process.Sizes and distributions of retained austenite and high-carbon martensite surrounded by martensite laths can be manipulated by the partitioning duration and temperature,and quenching temperature of the S-Q-P process.Alloying element Si is employed in the S-Q-P steel to suppress formation of carbides and create suitable amount of retained austenite.A steel of 0.39C-1.22Mn-1.12Si-0.23Cr(wt.%) treated by the S-Q-P process is endowed with some special microstructural characteristics:some strips of retained austenite located at edges of martensite blocks with high density of dislocations and between martensite laths,some small blocks of twinned martensites distributed among bundles of the low-carbon martensite lath.The mechanical properties of the medium carbon steel after the S-Q-P process can reach ultimate tensile strength(Rm) of 1240 MPa,total elongation(EI) of 25%,and product of strength and ductility(PSD) of 31.2 GPa% that are much more improved than those after the conventional quenching-tempering(Q-T) and currently prevailing quenching-partitioning(Q-P) treatments.The PSD of the tested steel after the S-Q-P process increases by 67% and 32% as compared with those after the Q-T and Q-P processes,respectively.展开更多
A light-weight high-entropy alloy （LWHEA） A120Be20Fe10SilsTi35 has been developed to have unique mechanical properties and oxidation resistance. One major and two minor phases are observed in the as-east microstruct...A light-weight high-entropy alloy （LWHEA） A120Be20Fe10SilsTi35 has been developed to have unique mechanical properties and oxidation resistance. One major and two minor phases are observed in the as-east microstructure. The density of the alloy is 3.91 gcm-3, and its hardness is HV 911, which is higher than quartz. The hardness and hardness to density ratio are the highest of all light-weight alloys reported before. In addition, it has excellent oxidation resistance at 700℃ and 900℃, which far exceeds that of Ti-6A1-4V. Thus, the combination of properties is promising for high-temperature applications, which require light weight, wear-resistant and oxidation-resistant components.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.51701114,11604204,51471063,51271111)the Youth Teacher Development Program of Shanghai Universities(Grant No.ZZGCD15101)+1 种基金Scientific Research Project of Shanghai University of Engineering ScienceTalents Project of Shanghai University of Engineering Science
文摘The Ti Bw reinforced near-α titanium matrix composite（Ti-5.8 Al-3.4 Zr-4.0 Sn-0.4 Mo-0.4 Nb-0.4 Si-0.06 C） was successfully synthesized by powder metallurgy and hot extrusion route. The effects of solution and aging temperature on the microstructure and high temperature tensile properties of the composite were investigated. The results revealed that the fine transformed β phase can be obtained by the solution treatment at β phase region and aging treatment, no other precipitates were observed. The α2 phase（Ti3 Al） can be acquired when the solution treated at α＋β phase region followed by aging treatment. With increasing the aging temperature from 500 to 700℃ for 5 h, the size of α2 precipitates increases from about 5 to about 30 nm. The Ti Bw are stable without any interfacial reaction during the heat treatments. The high temperature tensile properties show that the composite performed by solution and aging treatment exhibits good strengthening effects. With increasing the aging temperature from 500 to 700℃, the strength of the composite increases at the expense of elongation due to the increment of α2 precipitates.The strength of the composite at 600℃ increases by 17% to 986 MPa after 1000℃/2 h/AC and 700℃/5 h/AC heat treatment.
基金Ministry of Science and Technology is acknowledged for the financial funding of the"973 program" of Grant No. 2010CB630800
文摘In order to meet the progressive requirement for the performance improvement of steel,the author proposed a novel microstructure featured with multi-phase,meta-stable and multi-scale(so-called as M 3).And then,the new technologies could be developed to process three prototype steels with high performance:the third generation high strength low alloy(HSLA) steels with improved toughness and/or ductility(AKV(40℃)≥200 J and/or A≥20% when Rp0.2 in 800-1000 MPa),the third generation advanced high strength steels(AHSS)(Rm×A≥30 GPa% when Rm from 1000 MPa to 1500 MPa) for automobiles with improved ductility and low cost,and heat resistant martensitic steels with improved creep strength(10000650≥90 MPa).It can be expected that the new technology developed will remarkably improve the safety and reliability of steel products in service for infrastructures,automobiles and fossil power station in the future.
基金supported by the National Basic Research Program of China (973 program) (Grant No. 2010CB630805)
文摘Based on gradient control of carbon partitioning between martensite and austenite during heat treatment of steels,a stepping-quenching-partitioning(S-Q-P) process is developed for high strength steels.The S-Q-P process involves several quenching processes at progressively lower temperatures between martensite-start(Ms) and martensite-finish(Mf) temperatures,each followed by a partitioning treatment at either the initial quenching temperature or above that temperature.A novel microstructure is designed based on the S-Q-P process.Sizes and distributions of retained austenite and high-carbon martensite surrounded by martensite laths can be manipulated by the partitioning duration and temperature,and quenching temperature of the S-Q-P process.Alloying element Si is employed in the S-Q-P steel to suppress formation of carbides and create suitable amount of retained austenite.A steel of 0.39C-1.22Mn-1.12Si-0.23Cr(wt.%) treated by the S-Q-P process is endowed with some special microstructural characteristics:some strips of retained austenite located at edges of martensite blocks with high density of dislocations and between martensite laths,some small blocks of twinned martensites distributed among bundles of the low-carbon martensite lath.The mechanical properties of the medium carbon steel after the S-Q-P process can reach ultimate tensile strength(Rm) of 1240 MPa,total elongation(EI) of 25%,and product of strength and ductility(PSD) of 31.2 GPa% that are much more improved than those after the conventional quenching-tempering(Q-T) and currently prevailing quenching-partitioning(Q-P) treatments.The PSD of the tested steel after the S-Q-P process increases by 67% and 32% as compared with those after the Q-T and Q-P processes,respectively.
文摘A light-weight high-entropy alloy （LWHEA） A120Be20Fe10SilsTi35 has been developed to have unique mechanical properties and oxidation resistance. One major and two minor phases are observed in the as-east microstructure. The density of the alloy is 3.91 gcm-3, and its hardness is HV 911, which is higher than quartz. The hardness and hardness to density ratio are the highest of all light-weight alloys reported before. In addition, it has excellent oxidation resistance at 700℃ and 900℃, which far exceeds that of Ti-6A1-4V. Thus, the combination of properties is promising for high-temperature applications, which require light weight, wear-resistant and oxidation-resistant components.
