The fabrication of nanocrystalline nickel coatings was conducted by pulse jet electrodeposition on the substrate of 45# carbon steel.The effects of average current density on the surface morphology,microstructure,aver...The fabrication of nanocrystalline nickel coatings was conducted by pulse jet electrodeposition on the substrate of 45# carbon steel.The effects of average current density on the surface morphology,microstructure,average grain size and microhardness of nickel coatings were investigated by scanning electron microscopy(SEM),X-ray diffractometry(XRD)and microhardness measurement.In addition,the corrosion resistances of coating and substrate were compared.It is revealed that the nickel coatings prepared by pulse jet electrodeposition exhibit a fine-grained structure with a smooth surface and a high density,although some pores and defects are still present in coatings.With the increase of average current density,the average grain size of nickel coatings is reduced at first and then increased.The coating with the optimum compactness,the smallest average grain size(13.7 nm)and the highest microhardness are obtained at current density of 39.8 A/dm2.The corrosion resistance is obviously increased for the coatings prepared by pulse jet electrodeposition;however,the corrosion rate is increased after a certain period due to the penetration of the corrosive media.展开更多
The microstructure and properties of the 93W-4Ni-2Co-1Fe(mass fraction,%) tungsten heavy alloys prepared by mechanical alloying and electric current activated sintering from mixed elemental powders were investigated.A...The microstructure and properties of the 93W-4Ni-2Co-1Fe(mass fraction,%) tungsten heavy alloys prepared by mechanical alloying and electric current activated sintering from mixed elemental powders were investigated.After 15 h milling,the average W grain size in the powders is decreased to 120 nm.For the powders milled for 15 h,the density,hardness and transverse rupture strength of the alloys sintered only by an intensive pulse electric current are the maximum.When the total sintering time keeps constant,the properties of the sintered alloys can be obviously improved by optimizing the sintering time of pulse-and constant-currents.A bulk ultrafine alloy with an average W grain size of about 340 nm can be obtained by sintering 15 h-milled powders in a total sintering time of 6 min.The corresponding sintered density,hardness and transverse rupture strength reach 16.78 g /cm3,HRA84.3 and 968 MPa,respectively.展开更多
Ni-W-P base composites containing CeO2 and SiO2 nano-particles were prepared on common carbon steel surface by pulse co-deposition of Ni,W,P,CeO2 and SiO2 nano-particles.The influence of SiO2 concentrations in bath on...Ni-W-P base composites containing CeO2 and SiO2 nano-particles were prepared on common carbon steel surface by pulse co-deposition of Ni,W,P,CeO2 and SiO2 nano-particles.The influence of SiO2 concentrations in bath on microstructures and properties of Ni-W-P/CeO2-SiO2 composites was studied,and the characteristics were assessed by chemical compositions,element distribution,surface morphologies,deposition rate and microhardness.The results indicate that when SiO2 concentration in bath is controlled at 20 g/L,the composites possess the fastest deposition rate,the highest microhardness,compact microstructures,smaller crystallite sizes and uniform distribution of W,P,Ce and Si within Ni-W-P matrix metal.Increasing SiO2 concentration in bath from 10 to 20 g/L leads to the refinement in grain size and the inhomogeneity of microstructures.While when SiO2 concentration is increased to 30 g/L,the crystallite sizes increase again and some bosses with nodulation shape appear on the surface of composites.展开更多
Most of the materials used in engineered cementitious composite are fine in size to achieve ductile nature.Stone slurry powder(SSP)is an inert material obtained from stone industries as by-product which may cause haza...Most of the materials used in engineered cementitious composite are fine in size to achieve ductile nature.Stone slurry powder(SSP)is an inert material obtained from stone industries as by-product which may cause hazardous impact on environment.In this research work,partial replacement of silica sand(SS)and fine sand(FS)by SSP with different contents(25%and 50%each)for making engineered cementitious composite has been explored.The performance was evaluated on the basis of strength,tensile strain,mid span deflection capacity,ultra-sonic pulse velocity and microstructure.Mechanical strength was found to be increased at 25%SSP in both replacements;whereas,strength decreased slightly at 50%replacement.Tensile strain,mid span deflection and quality of concrete were enhanced with increase in SSP content.Using SSP formed denser cementitious composite can help to save the natural resources and contribute in making green cementitious composite.展开更多
基金Project(50175053) supported by the National Natural Science Foundation of China
文摘The fabrication of nanocrystalline nickel coatings was conducted by pulse jet electrodeposition on the substrate of 45# carbon steel.The effects of average current density on the surface morphology,microstructure,average grain size and microhardness of nickel coatings were investigated by scanning electron microscopy(SEM),X-ray diffractometry(XRD)and microhardness measurement.In addition,the corrosion resistances of coating and substrate were compared.It is revealed that the nickel coatings prepared by pulse jet electrodeposition exhibit a fine-grained structure with a smooth surface and a high density,although some pores and defects are still present in coatings.With the increase of average current density,the average grain size of nickel coatings is reduced at first and then increased.The coating with the optimum compactness,the smallest average grain size(13.7 nm)and the highest microhardness are obtained at current density of 39.8 A/dm2.The corrosion resistance is obviously increased for the coatings prepared by pulse jet electrodeposition;however,the corrosion rate is increased after a certain period due to the penetration of the corrosive media.
基金Project(2007CB616905) supported by the National Basic Research Program of ChinaProject(2007AA03Z112) supported by the National High-tech Research and Development Program of China+1 种基金Project(x2jqB6080210) supported by the Natural Science Foundation of Guangdong Province,ChinaProject(9140A18040709JW1601) supported by the Advanced Research Fund of Department of Defense,China
文摘The microstructure and properties of the 93W-4Ni-2Co-1Fe(mass fraction,%) tungsten heavy alloys prepared by mechanical alloying and electric current activated sintering from mixed elemental powders were investigated.After 15 h milling,the average W grain size in the powders is decreased to 120 nm.For the powders milled for 15 h,the density,hardness and transverse rupture strength of the alloys sintered only by an intensive pulse electric current are the maximum.When the total sintering time keeps constant,the properties of the sintered alloys can be obviously improved by optimizing the sintering time of pulse-and constant-currents.A bulk ultrafine alloy with an average W grain size of about 340 nm can be obtained by sintering 15 h-milled powders in a total sintering time of 6 min.The corresponding sintered density,hardness and transverse rupture strength reach 16.78 g /cm3,HRA84.3 and 968 MPa,respectively.
基金Project(20806035) supported by the National Natural Science Foundation of ChinaProject(2009CI026) supported by Back-up Personnel Foundation of Academic and Technology Leaders of Yunnan Province,China+4 种基金Project(KKZ6200927001) supported by Opening Fund of Key Laboratory of Inorganic Coating Materials, Chinese Academy of Sciences Project(2007E187M) supported by Applied Basic Research Plans of Yunnan Province,ChinaProject(08C0025) supported by Scientific Research Fund of Yunnan Provincial Education Department, China Project(KKZ3200927029) supported by Training Foundation for Talents of Kunming University of Science and Technology,ChinaProject(2008-003) supported by Analysis and Measurement Research Fund of Kunming University of Science and Technology,China
文摘Ni-W-P base composites containing CeO2 and SiO2 nano-particles were prepared on common carbon steel surface by pulse co-deposition of Ni,W,P,CeO2 and SiO2 nano-particles.The influence of SiO2 concentrations in bath on microstructures and properties of Ni-W-P/CeO2-SiO2 composites was studied,and the characteristics were assessed by chemical compositions,element distribution,surface morphologies,deposition rate and microhardness.The results indicate that when SiO2 concentration in bath is controlled at 20 g/L,the composites possess the fastest deposition rate,the highest microhardness,compact microstructures,smaller crystallite sizes and uniform distribution of W,P,Ce and Si within Ni-W-P matrix metal.Increasing SiO2 concentration in bath from 10 to 20 g/L leads to the refinement in grain size and the inhomogeneity of microstructures.While when SiO2 concentration is increased to 30 g/L,the crystallite sizes increase again and some bosses with nodulation shape appear on the surface of composites.
基金Project(F1-17.1/2017-18/MANF-2017-18-HAR-78129)supported by the University Grants Commission New Delhi,India。
文摘Most of the materials used in engineered cementitious composite are fine in size to achieve ductile nature.Stone slurry powder(SSP)is an inert material obtained from stone industries as by-product which may cause hazardous impact on environment.In this research work,partial replacement of silica sand(SS)and fine sand(FS)by SSP with different contents(25%and 50%each)for making engineered cementitious composite has been explored.The performance was evaluated on the basis of strength,tensile strain,mid span deflection capacity,ultra-sonic pulse velocity and microstructure.Mechanical strength was found to be increased at 25%SSP in both replacements;whereas,strength decreased slightly at 50%replacement.Tensile strain,mid span deflection and quality of concrete were enhanced with increase in SSP content.Using SSP formed denser cementitious composite can help to save the natural resources and contribute in making green cementitious composite.
