高超声速变后掠飞行器多变量预设性能控制

本文针对高超声速变后掠飞行器姿态控制,设计了多变量预设性能与滑模相结合的控制器。首先,建立了强耦合非线性的变后掠飞行器模型,绘制了预设性能控制流程框图,并对控制器的有效性进行了论证;然后,针对飞行器的姿态角设计了预设性能函数,对误差进行同胚映射,解决了控制器设计过程中存在约束的问题,进而根据转换后的误差设计了滑模控制器及误差补偿器;最后,通过仿真验证了飞行器变后掠过程中姿态控制器的有效性,通过与滑模控制对比验证了控制器的优越性,并在风干扰的条件下验证了控制器的鲁棒性。

滑阀结构对比例泵变量性能的影响

分析了滑阀结构对比例泵变量性能的影响因素 。

飞行器射频隐身技术内涵及性能度量研究

在分析射频无源探测系统工作机理和国内外射频隐身研究情况基础上,指出射频隐身技术概念、多层次的隐身内涵和技术实现途径,提出了与敌对方侦察接收机技术体制和性能指标无关的、仅反映射频隐身自身性能的技术指标及其应用思路。

地图符号的视觉变量

视觉变量作为图形符号设计的理论基础，在地图符号设计中起着重要的作用。然而，笔者认为，Ｂｅｒｔｉｎ所提出的视觉变量有些对地图符号并不适用。本文提出了用于构造地图符号的视觉变量，并对它们的感受性能作了初步的探讨。

Multiple attribute decision making method based on trapezoid fuzzy linguistic variables

The problem of multiple attribute decision making under fuzzy linguistic environments, in which decision makers can only provide their preferences （attribute values）in the form of trapezoid fuzzy linguistic variables（TFLV）, is studied. The formula of the degree of possibility between two TFLVs is defined, and some of its characteristics are studied. Based on the degree of possibility of fuzzy linguistic variables, an approach to ranking the decision alternatives in multiple attribute decision making with TFLV is developed. The trapezoid fuzzy linguistic weighted averaging （TFLWA） operator method is utilized to aggregate the decision information, and then all the alternatives are ranked by comparing the degree of possibility of TFLV. The method can carry out linguistic computation processes easily without loss of linguistic information, and thus makes the decision results reasonable and effective. Finally, the implementation process of the proposed method is illustrated and analyzed by a practical example.

Hot deformation behavior of spray forming LSHR alloy using constitutive equation and processing map

Flow behaviors of spray forming low solvus high refractory (LSHR) alloy were investigated using hot compression tests performed on a Gleeble?3500 thermal mechanical simulator at temperatures of 1020?1150 °C and strain rates of 0.0003?1.0 s?1. The constitutive equation was established, power dissipation (η) maps and hot processing maps were plotted. The microstructure evolution and dislocation distribution of domains with different values of η in power dissipation maps were also observed. The results show that the flow stress increases with decreasing temperature and increasing strain rate. The activation energy of the spray forming LSHR alloy is 1243.86 kJ/mol. When the value of η is 0.36 at the strain of 0.5, the domain in the processing map shows characteristics of typical dynamic recrystallization (DRX) and low dislocation density. According to the microstructure evolution and processing maps, the optimum processing condition for good hot workability of spray forming LSHR alloy can be summed up as:temperature range 1110?1150 °C; strain rate range 0.01?0.3 s?1.

Rotating extrusion technique and its effect on quality of aluminum alloy thin-plate weldments

A new technique named rotating extrusion was proposed that uses rotating extrusion action to rectify residual distortion of aluminum alloy thin-plate weldments to improve mechanical properties of welded joints. The basic principle and device of rotating extrusion were introduced. The residual distortion and stresses in rotating extrusion weldments were compared with those in conventional weldments. The differences in microstructure and mechanical properties between conventional welded joints and rotating extrusion welded joints were investigated and analyzed in order to make clear the effect of rotating extrusion on the performance of aluminum alloy weldments. Experimental results show that rotating extrusion can enhance the hardness and tensile strength of aluminum alloy welded joints evidently. This method has also potential effect on extending the life of welded structures.

A new method of characterizing equivalent strain for equal channel angular processing

In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new approach to characterize the equivalent strain was proposed. The results show that there exists better accordance between mechanical property （such as hardness or strength） and equivalent strain after rolling and ECAP in a certain range of deformation amount, and Gauss equation can be satisfied among the equivalent strain and the mechanical properties for ECAP. Through regression analysis on the data of hardness and strength after the deformation, a more generalized expression of equivalent strain for ECAP is proposed as：ε=k0exp[-（k1M-k2）^2], where M is the strength or hardness of the material, k1 is the modified coefficient （k1∈ （0, 1））, ko and k2 are two parameters dependent on the critical strain and mechanical property that reaches saturation state for the material, respectively. In this expression the equivalent strain for ECAP is characterized novelly through the mechanical parameter relating to material property rather than the classical geometry equation.

Extended Group Foliation Method and Functional Separation of Variables to Nonlinear Wave Equations

Generalized functional separation of variables to nonlinear evolution equations is studied in terms of the extended group foliation method, which is based on the Lie point symmetry method. The approach is applied to nonlinear wave equations with variable speed and external force. A complete classification for the wave equation which admits functional separable solutions is presented. Some known results can be recovered by this approach.

矿用带式输送机新型安全检测设备设计

现阶段关于带式输送机的性能检测设备性能过于单一,在面对复杂情况时不能有效地检测和处理故障。因此,根据带式输送机的常见故障和特定条件下的故障隐患设计一种基于PXI体系的性能参变量检测设备,该设备功能全面,数据测量快速准确,能够满足日常生产中带式输送机的性能参变量实时检测需求。

Macroalgae in a spring stream in Shanxi Province:composition and relation to physical and chemical variables

Fourteen stream segments were investigated throughout the Xin’an Spring in Shanxi Province, China in 2004. The variation ranges in stream size, current velocity, discharge, dissolved oxygen, and specific conductance were large. Twenty-two macroalgae species were found in the stream. Major divisions in terms of species numbers were Chlorophyta (59.1%), Cyanophyta (22.8%), Xanthophyta (9.1%), Rhodophyta (4.5%) and Charophyta (4.5%). The most widespread species, Cladophora rivularis (50.0%), also Oedogonium sp. (42.9%) and Spirogyra sp. (42.9%) were well represented throughout the stream, whereas another 10 species were found in only one sampling site. Total percentage cover varied from <1% to 90%. Red algae Batrachospermum acuatum and the charophytes Chara vulgaris have the highest percentage cover. Among the parameters analyzed, the stream width, specific conductance and dissolved oxygen were the ones that more closely related to the species number and percentage cover of macroalgal communities. The species number of each site was negatively correlated with dissolved oxygen content. The total percentage cover of the macroalgae was negatively correlated with the stream width and the specific conductance.

Experimental Study on the Viscoelastic Behaviors of Debris Flow Slurry

The rheological properties of most liquid in nature are between liquids and solids, including both elastic changes and viscosity changes, that is socalled ＂viscoelastic＂. Dynamic oscillatory test was used to quantitatively study the distinct viscoelastic behaviors of debris flow slurry in the shear stress conditions for the first time in this study. The debris flow slurry samples were from Jiangjiagou Ravine, Yunnan Province, China. The experimental results were found that at the low and middle stages of shearing, when the angular velocity 09〈72.46 s-1, the loss modulus （G was greater than the storage modulus （G3, i.e. G＂〉G＇. At the late stage of shearing, when the angular velocity co-72.46 s-x, the storage modulus was greater than or equal to the loss G = G, tan -〈 1 （where phase-shift modulus, i.e. ＇ 〉 ＂ angle 5=G＂,/G3, and the debris flow slurry was in a gel state. Therefore, the progress of this experimental study further reveals the mechanism of hyperconcentrated debris flows with a high velocity on low-gradient ravines.

Performance Monitoring and Diagnosis of Multivariable Model Predictive Control Using Statistical Analysis

A statistic-based benchmark was proposed for performance assessment and monitoring of model predic- tive control; the benchmark was straightforward and achievable by recording a set of output data only when the control performance was good according to the user’s selection. Principal component model was built and an auto- regressive moving average filter was identified to monitor the performance; an improved T2 statistic was selected as the performance monitor index. When performance changes were detected, diagnosis was done by model validation using recursive analysis and generalized likelihood ratio (GLR) method. This distinguished the fact that the per- formance change was due to plant model mismatch or due to disturbance term. Simulation was done about a heavy oil fractionator system and good results were obtained. The diagnosis result was helpful for the operator to improve the system performance.

Perturbation of Symmetries and Mei Adiabatic Invariants of Nonholonomic Systems with Servoconstraints

The perturbation of symmetries and Mei adiabatic invariants of nonholonomic systems with servoconstraints are studied. The exact invariants in the form of Mei conserved quantities introduced by the Mei symmetry of nonholonomic systems with servoconstraints without perturbations are given. Based on the definition of higher-order adiabatic invariants of mechanical systems, the perturbation of Mei symmetries for nonholonomic .systems with servoconstraints under the action of small disturbance is investigated, and Mei adiabatic invatiants of the system are obtained. An example is given to illustrate the application of the results.

Novel histogram descriptor for global feature extraction and description

A novel histogram descriptor for global feature extraction and description was presented. Three elementary primitives for a 2×2 pixel grid were defined. The complex primitives were computed by matrix transforms. These primitives and equivalence class were used for an image to compute the feature image that consisted of three elementary primitives. Histogram was used for the transformed image to extract and describe the features. Furthermore, comparisons were made among the novel histogram descriptor, the gray histogram and the edge histogram with regard to feature vector dimension and retrieval performance. The experimental results show that the novel histogram can not only reduce the effect of noise and illumination change, but also compute the feature vector of lower dimension. Furthermore, the system using the novel histogram has better retrieval performance.

Effects of calcium addition on as-cast microstructure and mechanical properties of Mg-5Zn-5Sn alloy

The effects of Ca addition on the as-cast microstructure and mechanical properties of the Mg-5Zn-5Sn (mass fraction,%) alloy were investigated.The results indicate that an addition of 0.5%-1.5% (mass fraction) Ca to the Mg-5Zn-5Sn alloy not only refines the as-cast microstructure of the alloy but also causes the formation of the primary and/or eutectic CaMgSn phases with high thermal stability;an increase in Ca amount from 0.5% to 1.5% (mass fraction) increases the amount and size of the CaMgSn phase.In addition,Ca addition to the Mg-5Zn-5Sn alloy improves not only the tensile properties at room temperature and 150 ℃ but also the creep properties.Among the Ca-containing Mg-5Zn-5Sn alloys,the one added 0.5% (mass fraction) Ca obtains the optimum ultimate tensile strength and elongation at room temperature and 150 ℃,however,the alloy added 1.5% (mass fraction) Ca exhibits the optimum yield strength and creep properties.

Effect of Operation Variables on Hydrodenitrogenation and Hydrodesulfurization over NiMo/Al_2O_3 Catalysts

Using the JQ-II high pressure hydrogenation micro-reactor unit, the reactivity of Athabasca bitumen derived heavy gas oil was studied over commercial and homemade hydrotreating catalysts. The effects of catalyst preparation variables and the influences of operation conditions, such as pressure, temperature, hydrogen/oil ratio and space velocity were also examined. It was shown that the optimal concentrations of the active components were 5% of NiO, 20% of MoO3 and 3.5% of phosphorus (by mass), and the suitable operation conditions were determined experimentally.

Assessment of Model Predictive Control Performance Criteria

The current highly competitive environment has driven industries to operate with increasingly restricted profit margins. Thus, it is imperative to optimize production processes. Faced with this scenario, multivariable predictive control of processes has been presented as a powerful alternative to achieve these goals. Moreover, the rationale for implementation of advanced control and subsequent analysis of its post-match performance also focus on the benefits that this tool brings to the plant. It is therefore essential to establish a methodology for analysis, based on clear and measurable criteria. Currently, there are different methodologies available in the market to assist with such analysis. These tools can have a quantitative or qualitative focus. The aim of this study is to evaluate three of the best current main performance assessment technologies： Minimum Variance Control-Harris Index; Statistical Process Control （Cp and Cpk）; and the Qin and Yu Index. These indexes were studied for an alumina plant controlled by three MPC （model predictive control） algorithms （GPC （generalized predictive control）, RMPCT （robust multivariable predictive control technology） and ESSMPC （extended state space model predictive controller）） with different results.

Studying of Physical-Mechanical Properties of Rocks of Geological Section Considering the Influences of Recent Geodynamics

The method of determination of elastic moduli of the geological section rocks had been developed in real conditions. The method is based on application of non-classically linearized theory of elastic waves＇ propagation in the deformable media and utilization of neural networks when creating the geoseismic model. It is proposed to forecast the thin-layer model of medium by velocities of the shear waves on the base of seismic inversion of 2D profile by neural networks and geophysical well logging data. The method had been tested on materials of geophysical well logging data and 2D seismic profile related to one of the structures in the South-Caspian depression. The specific results for Poisson coefficient and elastic moduli of the third order had been obtained. The mentioned method can also be applied to forecast of other physical-mechanical properties of the medium.

Multivariable fuzzy control of residential inverter-driven air conditionings

A model free intelligent muhivariable fuzzy controller （MFC） designed for modulating the vapor compression cycles in a residential inverter-driven air conditioning is proposed. The novel controller combines a traditional fuzzy controller （TFC） and an additional coupling fuzzy controller, the coupling fuzzy controller is introduced to compensate for the unknown cross-coupling effects of this muhivariable system. In order to evaluate the control performance of the MFC, it is digitally implemented in terms of regulating the desired evaporating temperature and superheat. The experimental results show the effectiveness of the MFC for improvement of system performance and energy efficiency.