Asymmetrical Fabry-Perot cavity slot micro-ring resonator and its sensing characteristics

To achieve high quality factor and high-sensitivity refractive index sensor,a slot micro-ring resonator(MRR)based on asymmetric Fabry-Perot(FP)cavity was proposed.The structure consisted of a pair of elliptical holes to form an FP cavity and a microring resonator.The two different optical modes generated by the micro-ring resonator were destructively interfered to form a Fano line shape,which improved the system sensitivity while obtaining a higher quality factor and extinction ratio.The transmission principle of the structure was analyzed by the transfer matrix method.The transmission spectrum and mode field distribution of the proposed structure were simulated by the finite difference time domain(FDTD)method,and the key structural parameters affecting the Fano line shape in the device were optimized.The simulation results show that the quality factor of the device reached 22037.1,and the extinction ratio was 23.9 dB.By analyzing the refractive index sensing characteristics,the sensitivity of the structure was 354 nm·RIU−1,and the detection limit of the sensitivity was 2×10−4 RIU.Thus,the proposed compact asymmetric FP cavity slot micro-ring resonator has obvious advantages in sensing applications owing to its excellent performance.

用X射线对医用X线胶片进行感光测定时曝光条件的探讨

经过十四年的努力，国际标准化组织新近颁布了ISO9236－l：摄影术一医学放射照相屏片系统感光测定学一第一部分：感光测定曲线，感光度和平均斜率的测定，意在建议P成员采纳贯彻该标准。本文简述了该标准中的最棘手部分：X射线曝光条件，且加以了讨论。

柯达天文底片103a-O和IIa-O的性能变化及其对比研究

美国柯达公司生产的天文底片103a-O和IIa-O是广泛使用了几十年的老牌品种.它们牌号不改,性能却多次变化,特别是IIa-O,然而当代世界上的天文用户们并未注意到这些变化.为此,本文重新把这些牌号未改但性能已改的底片做了感光学对比研究. 对我们比较的底片,未敏化使用时,IIa-O(批号HD1A6)比103a-O(批号HD215)速度稍快;颗粒却较细;特性曲线较平坦;输出信噪比和探测量子效率差不多.综合看,现在的IIa-O性能倒是比现在的103a-O更接近五十年代的103a-O.但经过气体敏化,103a-O的感光学性能仍然稍微优于IIa-O.

An Open-Loop Test of a Resonator Fiber Optic Gyro

The resonator fiber optic gyro （R-FOG） ,which utilizes a resonance frequency change due to the Sagnac effect,is a promising candidate for the next generation inertial rotation sensor. In this study, an open-loop R-FOG is set up using phase modulation spectroscopy. First,the demodulation curve is obtained using a lock-in amplifier. From the demodulation signal,a gyro dynamic range of ± 4.2rad/s is obtained. Then,using different phase modulation frequencies,the open-loop gyro output signal is measured when the gyro is rotated clockwise or counterclockwise. The bias drift as a function of time is also measured. The fluctuation of the output over 5s is about 0.02rad/s. The drift can be reduced by taking countermeasures against system noise.

FIBER OPTIC TEMPERATURE MEASURING SYSTEM

This paper presents a fiber optic temperature measuring system used for measuring the temperature in many occasions. The system is of reflective type and composed of thermostatic bimetal plate, lever piston framework, optical grating and optical fiber probes. When the temperature changes, the thermostatic bimetal plate deforms. Through lever piston framework, the optical grating produces displacement in the upright direction. Thus the change of the temperature is transformed into the upright displacement of the optical grating. Optical fiber probes are used for detecting the number of streak lines of the optical grating′s displacement depending on the change of temperature. The detected signal can be transmitted to the control center through optical fiber cable up to distance of 1 km. The measurable range of this system reaches 100℃ with accuracy of ±0.2℃.

EXPERIMENTAL STUDY ON OPTIC PERFORMANCES OF OPTIC FIBER BRAIDED IN CARBON FIBER BRAIDED COMPOSITES

D braiding technology has stimulated a great deal of interest in the world at large and been widely used in aerospace, military, civil construction and medical fields. Although 3 D braided composites have many good features, their features are very complicated. Optic fiber sensors can be multi braided into 3 D braided composites to fulfill a new kind of 3 D smart composites to monitor RTM process, study mechanical behaviors and damage states after molding, and monitor its own condition during service life. Since optic performances of optic fibers have direct and important relation to the performances of optic fiber sensors, experimental research is done to devise a method to incorporate the optic fiber into a 3 D structure. The optical performances of the braided optic fibers are tested and compared with the original one to study the optic performances of optic fibers, before their being braided into composites and after the RTM process.

An Approach to Improving the Retrieval Accuracy of Oceanic Constituents in Case Ⅱ Waters

In the present paper, a method is proposed to improve the performance of Artificial Neural Network (ANN) based algorithms for the retrieval of oceanic constituents in Case Ⅱ waters. The ANN-based algorithms have been developed based on a constraint condition, which represents, to a certain degree, the correlation between suspended particulate matter (SPM) and pigment (CHL), coloured dissolved organic matter (CDOM) and CHL, as well as CDOM and SPM, found in Case Ⅱ waters. Compared with the ANN-based algorithm developed without a constraint condition, the performance of ANN-based algorithms developed with a constraint conditions is much better for the retrieval of CHL and CDOM, especially in the case of high noise levels; however, there is not significant improvement for the retrieval of SPM.

A novel temperature-insensitive strain sensor based on tapered fiber grating

A novel temperature-insensitive strain sensor based on bandwidth demodulation of the reflected light from the tapered fiber grating is presented, which is simple and low-cost and has considerable potential particularly application for strain sensing,and with the development of the interrogation system, it can demodulate both the bandwidth and the center wavelength of the reflected light from TFG to measure strain and temperature simultaneously.

Using Unmanned Underwater Vehicles as Research Platforms in Coastal Ocean Studies

The advantages of using unmanned underwater vehicles in coastal ocean studies are emphasized. Two types of representative vehicles, remotely operated vehicle (ROV) and autonomous underwater vehicle (AUV) from University of South Florida, are discussed. Two individual modular sensor packages designed and tested for these platforms and field measurement results are also presented. The bottom classification and albedo package, BCAP, provides fast and accurate estimates of bottom albedos, along with other parameters such as in-water remote sensing reflectance. The real-time ocean bottom optical topographer, ROBOT, reveals high-resolution 3-dimentional bottom topography for target identification. Field data and results from recent Coastal Benthic Optical Properties field campaign, 1999 and 2000, are presented. Advantages and limitations of these vehicles and applications of modular sensor packages are compared and discussed.

Influence of stress birefringence on the performance of a FBG pressure sensor

The effects of using overall affix and two-spot affix between the FBG and underlay on the characteristics of the pressure sensors are compared both experimentally and theoretically.It is found that overall affix can produce large nonlinear effect on the characteristics of output of the sensors.The nonlinear effect caused by the expanded spectral width mainly due to the stress birefringence and the stress grads etc.The experimental result shows that the spectral width caused by using overall affix is 0.28 nm and the linearity can have up to 1.89% of increasing by using two-spot affix.The method of two-spot affix can improve response characteristics of the sensor which is benefit to achieve wavelength demodulation and to improve measurement precision.

Remote Sensing Image Segmentation with Probabilistic Neural Networks

This paper focuses on the image segmentation with probabilistic neural networks (PNNs). Back propagation neural networks (BpNNs) and multi perceptron neural networks (MLPs) are also considered in this study. Especially, this paper investigates the implementation of PNNs in image segmentation and optimal processing of image segmentation with a PNN. The comparison between image segmentations with PNNs and with other neural networks is given. The experimental results show that PNNs can be successfully applied to image segmentation for good results.

Study on rock deformation monitoring using fiber Bragg grating in simulation experiment

Presented the fiber Bragg grating （FBG） sensors for rock strain monitoring in the 1.2 m long plane stress model of the simulation experiment. In the past, for the lack of appropriate technique to measure the deformation of rock structures, the measurement of deflection was restricted to just a few discrete points along rock, and the measuring points were limited to the location installed with displacement transducers. We developed a method to monitor the deformation of rock structures using fiber optical Bragg grating strain sensors. The sensors were embedded in rock layers of simulation experiment before the materials were put in. These sensors were then used to monitor the experienced strain with different face advancing distance. The test results indicate that, if properly installed, FBG sensors can survive under severe conditions associated with embedment process and yield accurate measurements of strains response. At the same time, we make comparisons of the data obtained by FBG sensors with those by centesimal gauge. The interest in FBG sensors was motivated by the potential advantages that they can offer more than existing sensing technologies.

How to realize a negative refractive index material at the atomic level in an optical frequency range?

The theoretical mechanism for realizing a negative refractive index material in an optical frequency range with an atomic gas system of electromagnetically induced transparency (EIT) is studied. It is shown that under certain conditions such a dense gas can exhibit simultaneously negative permittivity and negative permeability, and negligibly small loss.

Optical fiber based slide tactile sensor for underwater robots

In the underwater environment, many visual sensors don’t work, and many sensors which work well for robots working in space or on land can not be used underwater. Therefore, an optical fiber slide tactile sensor was designed based on the inner modulation mechanism of optical fibers. The principles and structure of the sensor are explained in detail. Its static and dynamic characteristics were analyzed theoretically and then simulated. A dynamic characteristic model was built and the simulation made using the GA based neural network. In order to improve sensor response, the recognition model of the sensor was designed based on the ‘inverse solution’ principle of neural networks, increasing the control precision and the sensitivity of the manipulator.

Study of a high-temperature and high-pressure FBG sensor with Al_2O_3 thin-wall tube substrate

A fiber Bragg grating(FBG) high-temperature and high pressure sensor has been designed and fabricated by using the Al2O3 thin-wall tube as a substrate.The test results show that the sensor can withstand a pressure range of 0-45 MPa and a temperature range of -10-300 ℃,and has a pressure sensitivity of 0.0426 nm/MPa and a temperature sensitivity of 0.0112 nm /

Fluorescence Enhancement of Polyamine Derivatives of 1,8-Naphthalimide with Transition Metal Ions

A series of fluorescent chemosensors 1-3 were synthesized to detect transition metal ions. At the room temperature, fluorescence intensities of these chemosensors in acetonitrile without transition metal ions were found to be very weak, due to the process of the efficient intramolecular photoinduced electron transfer （PET）. However, after addition of the transition metal ions, the chemoscnsor 1-3 exhibits obvious fluorescence enhancement. Moreover, the intensity of the fluorescence emission of chemosensors increases significantly in the presence of Zn^2＋ and Cd^2＋. The fluorescent chemosensors with different polyamine as receptors show diverse affinity abilities to the transition metal ions and signal the receptor-metal ion interaction by the intensity change of fluorescence emission.

Demodulation System for Fiber Bragg Grating Sensors Using Digital Filtering Technique

A discrimination measurement method and demodulation technique for fiber Bragg grating (FBG) sensors were presented using digital filtering technique. The system can control a tunable fiber Fabry-Perot filter with sawtooth wave voltage generated by digital clock to interrogate FBG sensors. Using the analogue digital converter (ADC), the reflected FBG signals were sampled with synchronous digital clock. With the aid of digital matched filtering technique, the sampled FBG signals were processed to obtain the maximum signal-to-noise ratio (SNR) and the Bragg wavelength shift from the FBG signals was recovered. The results demonstrate that this system has a scanning range of 1 520 nm-1 575 nm,and the wavelength detection accuracy is less than 2 pm with 1.5 Hz scanning frequency.

New High Sensitivity Pressure Transducer with Optical Fibre Link

The principle of new optical fibre pressure transducer is analysed, and ingenious design scheme of this transducer is given. This new transducer specimen is provided with following characteristics: experimental transmitting distance is 20 m (actually up to 1 000 m ); system sensitivity is 0. 1 mV/Pa; power consumption of the probe is less than 125 μW. Finally, some points of the appraisement are given in this paper.

High-sensitivity temperature sensor based on long-period fiber grating

Temperature sensitivity is greatly improved by taking the following three measures： proper long-period fiber grating （LPFG） whose strain coefficient of the core is larger than that of the cladding is employed, the LPFG is coated with a thin film of the material whose refractive index decreases with the temperature, and the sensor is encapsulated by metal material whose thermal expansion coefficient is large. By computer simulation, a measured temperature coefficient of 0.2375 nm/℃ and a temperature resolution less than 0.1 ℃ are obtained.

Design of fan beam optical sensor and its application in mass flow rate measurement of pneumatically conveyed solids

The fan-beam optical sensor is made up of many semiconductor lasers and detectors fixed around the wall alternately at a cross section of pneumatically conveying pipe. When the sensor works, a scanning light source emits a 50° lamellar fan-beam through the gas-solid two phase flow, and the projection data resulting extinction effect of solid particles are detected at the same time. With the projection data, the flow rate mass can be calculated, and then the flow image can be reconstructed. In this paper, the design of the sensor including spatial arrangement of the structural parts, basic principle and measurement sensitivity distribution are introduced. The mathematical measurement model of solid mass flow rate is presented together with the testing results.