电磁感应图象作图题一例

电磁感应图象作图题一例卢日伦（广西天等县高级中学，５３２８００）电磁感应图象作图题历来是高考中的难题，它考查的不仅是电磁感应的知识，更关键的是考查学生对图象与物理过程的对应关系的分析能力，而这点恰是学生的薄弱环节．本文试图从下面一个题目的分析和讨论，...

GIS在求解地基附加应力中的应用

依据Newmark感应图法基本原理,在对感应图稍做改进的基础上,将GIS的空间分析和数据管理功能应用于感应图法,求解任意形状竖向均布荷载作用下的地基附加应力。在计算机绘图的基础上,利用ARC/INFO软件进行图层拓扑叠加和空间数据及其属性数据的操作与管理,实现对任意形状、任意一点、任意深度的附加应力计算。同时,可以在计算机屏幕上显示各阶段图层及相应的属性数据,可视性强。根据需要,可随时进行图形和属性数据的调整。技术措施的实现过程简单,可操作性强。与传统的感应图法相比,减少了绘图工作量,消除了人为误差,提高了计算精度。

Effect of initial microstructure on hot workability of 7085 aluminum alloy

The hot workability of 7085 aluminum alloys with different initial microstructures （as-homogenized and as-solution treated） was studied by isothermal compression tests at the deformation temperature ranging from 300 to 450 ℃ and the strain rate ranging from 0.0001 to 1 s 1. The strain rate sensitivity of the alloy was evaluated and used for establishing the power dissipation maps and instability maps on the basis of the flow stress data. The results show that the efficiency of power dissipation for the as-homogenized alloy is lower than that of the as-solution treated alloy. The deformation parameters of the dynamic recrystallization for the as-homogenized and as-solution treated alloy occur at 400 ℃, 0.01 s i and 450 ℃, 0.001 s-1, respectively. The flow instability region of the as-homogenized alloy is narrower than that of the as-solution treated alloy. These differences of the alloys with two different initial microstructures on the processing maps are mainly related to the dynamic precipitation characteristics.

Principle and Analysis of Novel Gate-Induced Noise in Pixel MOSFET of CMOS Imagers

A detailed principle and a rigorous analysis of a new noise,the gate-induced noise,in pixel MOSFET of CMOS imagers are provided.The gate-induced noise of the MOSFET is more notable in the strong reversion region than that in the subthreshold region when the applied gate voltage is low.However,the applied gate voltage being up to 3V,the gate-induced noise is more notable with the ω/ω T increasing when the MOSFET operates in the subthreshold region than that in the strong reversion region.Between the photocurrent I D and the root mean square value of the gated-induced noise,current i 2 d presents the relation of i 2 d∝I D in the saturation region of the strong reversion and approximately i 2 d∝I D in the subthreshold region.A deta iled and rigorous study of the gate-induced noise in the reset MOSFET for the p hotodiode APS and improved photodiode APS are provided.The improvement of logari thmic response APS is analyzed and the simulation results show that the gate-in duced noise can be reduced.

Numerical Simulation and Analysis of Bipolar Junction Photogate Transistor for CMOS Image Sensor

A new photodetector--bipolar junction photogate transistor is presented for CMOS image sensor and its analytical model is also established.With the technical parameter of the 0.6μm CMOS process,the bipolar junction photogate transistor is analyzed and simulated.The simulated results illustrate that the bipolar junction photogate transistor has the similar characteristics of the traditional photogate transistor.The photocurrent density of the bipolar junction photogate transistor increases exponentially with the incidence light power due to introducing the injection p+n junction.Its characteristic of blue response is rather improved compared to the traditional photogate transistor that benefits to increase the color photograph made up of the red,the green,and the blue.

Fabrication of PdSe2/GaAs Heterojunction for Sensitive Near-Infrared Photovoltaic Detector and Image Sensor Application

In this study,we have developed a high-sensitivity,near-infrared photodetector based on PdSe2/GaAs heterojunction,which was made by transferring a multilayered PdSe2 film onto a planar GaAs.The as-fabricated PdSe2/GaAs heterojunction device exhibited obvious photovoltaic behavior to 808 nm illumination,indicating that the near-infrared photodetector can be used as a self-driven device without external power supply.Further device analysis showed that the hybrid heterojunction exhibited a high on/off ratio of 1.16×10^5 measured at 808 nm under zero bias voltage.The responsivity and specific detectivity of photodetector were estimated to be 171.34 mA/W and 2.36×10^11 Jones,respectively.Moreover,the device showed excellent stability and reliable repeatability.After 2 months,the photoelectric characteristics of the near-infrared photodetector hardly degrade in air,attributable to the good stability of the PdSe2.Finally,the PdSe2/GaAs-based heterojunction device can also function as a near-infrared light sensor.

A Review on Back-Propagation Neural Networks in the Application of Remote Sensing Image Classification

ANNs （Artificial neural networks） are used extensively in remote sensing image processing. It has been proven that BPNNs （back-propagation neural networks） have high attainable classification accuracy. However, there is a noticeable variation in the achieved accuracies due to different network designs and implementations. Hence, researchers usually need to conduct several experimental trials before they can finalize the network design. This is a time consuming process which significantly reduces the effectiveness of using BPNNs and the final design may still not be optimal. Therefore, there is a need to see whether there are some common guidelines for effective design and implementation of BPNNs. With this aim in mind, this paper attempts to find and summarize the common guidelines suggested by different authors through literature review and discussion of the findings. To provide readers with background and contextual information, some ANN fundamentals are also introduced.

Research on Direct Torque Control System Based on Induction Motor

The mathematic model of direct torque control (DTC) was deduced. Two simulating models based on the MATLAB & SIMULINK were established. The emphasis is focused on study of the performance difference of the DTC system with stator flux hexagon and circle trajectories. The simulation waveforms of flux, torque and current characters with two flux trajectories were given. Experiments were carried out in an AC drive system based on induction motor and two-level inverter. A dual-CPU structure was used and the communication with two CPUs was obtained by a dual-port RAM in this system.

Motifs of Revulsion in George Eliot＇s Middlemarch and Induction of Moral Conflicts

This paper selects revulsion and its networking emotion： resentment and disgust as a generic form of novel studies and the subject of moral investigation. Motifs of revulsion create complex bedding texture of the plot, which introduces personality and inner visions of characters in the novel. It unifies the binding power of narrative history and informs readers various aspects of morality in the Victorian era, in addition, to present a lyrical tone of social ethics. The following analysis takes Eliot＇s Middlemarch as the base text. I shall explain the lexical meaning and textual discussion of revulsion, resentment and disgust spirally within its context, then illustrate with paranthetical examples and different idioms. Later arguments turn to what Eliot defines as faction of human duty in life, which is the nuanced requirement of a subject stands against himself or herself through the disposition of conscience as verdict. This disposition provides unlimited parallels for instinctive presence of internal feelings and thresholds that are constantly affecting moral understandings.

Seismic Analysis for Rigid-Framed Prestressed Reinforced Concrete Bridge in Tianjin Light Railway

The seismic analysis of a rigid-framed prestressed concrete bridge in Tianjin Light Railway is performed. A 3-D dynamic finite element model of the bridge is established considering the weakening effect caused by the soft soil foundation. After the dynamic characteristics are calculated in terms of natural frequencies and modes, the seismic analysis is carried out using the modal response spectrum method and the time-history method, respectively. Based on the calculated results, the reasonable design values are finally suggested as the basis of the seismic design of the bridge, and meanwhile the problems encountered were also analyzed. Finally, some conclusions are drawn as: 1) Despite the superiority of rigid-framed prestressed concrete bridge, the upper and lower ends of the piers of the bridge are proved to be the crucial parts of the bridge, which are easily destroyed under designed earthquake excitations and should be carefully analyzed and designed; 2) The soft soil foundation can possibly result in rather weakening of the lateral rigidity of the rigid-framed bridge, and should be paid considerable attention; 3) The modal response spectrum method, combined with time-history method, is suggested for the seismic analysis in engineering design of the rigid-framed prestressed concrete bridge.

Primary Quantitative Study on Earthquake Damage Extracted from Remote Sensing Imagery——A Case Study of Seismic Damage in the Urban Area of Dujiangyan due to the M_S8.0 Wenchuan Earthquake

The fast developing remote sensing techniques play an increasingly important role in earthquake emergency response, disaster survey and loss estimation. As there is a lack of quantitative studies on seismic damage based on remote sensing, its practicality in seismic disaster management has usually been questioned. The paper introduces the essential quantitative study idea, the concept of the remote sensing seismic damage index （D1RS） and analysis models, demonstrates the seismic damage indices （ D1G ） of buildings obtained from ground surveying and its quantitative relation to D1RS in Dujiangyan city, Sichuan Province, which was destroyed by the 2008 Wenchuan earthquake with Ms8.0. The primary results show that an obvious relationship exists between the D1RS of buildings obtained from the high resolution satellite or aerial remote sensing images and D1G or the building collapse ratio obtained through ground survey, which suggests that the quantitative study on seismic damage based on remote sensing will provide an effective method for seismic damage survey and loss estimation.

The Representation of a Broadband Vector Field

Compared to a scalar pressure sensor, a vector sensor can provide a higher signal-to-noise ratio （SNR） signal and more detailed intbrmation on the sound field. Study on vector sensors and their applications have become a hot topic. Research on the representation of a vector field is highly relevant for extending the scope of vector sensor technology. This paper discusses the range-frequency distribution of the vector field due to a broadband acoustic source moving in a shallow-water waveguide as the self noise of a surface ship, and the vector extension of the waveguide impulse response measured over a limited frequency range using an active source of known waveform. From theory analysis and numerical simulation, the range-frequency representation of a vector field exhibits an interference structure qualitatively similar to that of the corresponding pressure field but, being quantitatively different, provides additional information on the waveguide, especially through the vertical component. For the range-frequency representation, physical quantities that can better exhibit the interference characteristics of the wavegaide are the products of pressure and particle velocity and of the pressure and pressure gradient. An image processing method to effectively detect and isolate the individual striations from an interference structure was reviewed briefly. The representation of the vector impulse response was discussed according to two different measurement systems, also known as particle velocity and pressure gradient. The vector impulse response representation can not only provide additional information from pressure only but even more than that of the range-frequency representation.

Research on assessing compression quality taking into account the space-borne remote sensing images

According to the remote sensing image characteristics, a set oi optimized compression quahty assessment methods is proposed on the basis of generating simulative images. Firstly, a means is put forward that generates simulative images by scanning aerial films taking into account the space-borne remote sensing camera characteristics （including pixel resolution, histogram dynamic range and quantization）. In the course of compression quality assessment, the objective assessment considers images texture changes and mutual relationship between simulative images and decompressed ima- ges, while the synthesized estimation factor （SEF） is brought out innovatively for the first time. Subjective assessment adopts a display setup -- 0.5mrn/pixel, which considers human visual char- acteristic and mainstream monitor. The set of methods are applied in compression plan design of panchromatic camera loaded on ZY-1-02C satellite. Through systematic and comprehensive assess- ment, simulation results show that image compression quality with the compression ratio of d：l can meet the remote sensing application requirements.

Information Service System for Receiving and Processing Multi Source Remote Sensing Images

Based on international requirements for the application of commercial remote sensing data,an information service system for receiving and processing multi source remote sensing data was developed and introduced.The system consists of an Oversea Fixed Ground Service Station(OFGS),a Transportable Vessel-Borne Service Station(TVBS) and a Data Operation and Management Center(DOMC).Fixed and transportable service stations were developed in Venezuela,Latin America and for the China's Xuelong polar research vessel respectively,and serve the function of remote sensing data receiving,processing and application.The DOMC connects the OFGS and TVBS,so that they constitute a network to provide receiving,distribution,retrieval,browsing,ordering,and downloading functions for multi remote sensing satellite data and products.It validates the competence in providing 40 kinds of typical application products.The development of this system provides a reliable and comprehensive service for commercial remote sensing data applications for users both in domestic and oversea markets.

等效矩形法计算不规则区域荷载下地基中附加应力

为简化基础底板形状不规则时的地基沉降计算,通过分析荷载区域几何形状对地基中附加应力的影响,提出以等效矩形替代原不规则荷载区域的等效矩形法。分析结果表明,均布荷载作用下,荷载区域总面积相同,且荷载强度相同时,若荷载区域几何形状不同,则在各自的最大沉降计算点下深度约为槡A/2处,地基中附加应力之间的差别最大,同时矩形中心点下该深度处的附加应力系数随着矩形圆形度的增加而增大。利用这一原理,对Newmark感应图法加以改进,提出3D-Newmark感应图法,以确定等效矩形的具体几何尺寸。

Improvement of ecological geographic regionalization based on remote sensing and canonical correspondence analysis： A case study in China

Ecological geographic regions, also called eco-regions, can be used to divide a remotely sensed image, which is helpful for reducing the complexity of land cover types within eco-regions and for improving the classification accuracy of land cover. In this case study in China, we improved a method of ecological geographic regionalization that is more suitable for remote sensing mapping of regional land cover, and we obtained new eco-regions. The canonical correspondence analysis(CCA) and k-means clustering were adopted in the ecological geographic regionalization using both seasonal remotely-sensed vegetation information and environmental data including climate, elevation and soil features. Our results show that the combination of seasonal vegetation information and the CCA performed well in the selection of the dominant environmental factor of the biogeographic pattern, and it can be used as regionalization indicators of eco-regions. We found that thermal factors are the most important driving forces of the biogeographic pattern in China, which followed by moisture factors. Two global land cover products(MODIS MCD12C1 and Glob Cover) were used to assess our eco-regions. The results show that our eco-regions performed better than that of a previous study regarding the complexity of land cover types, such as in the number of types and the proportional area of the major/secondary type. These results indicate that the method of ecological geographic regionalization, which is based on environmental factors associated with seasonal vegetation features, is effective for reducing the regional complexity of land cover.

Coordinated motion of molecular motors on DNA chains with branch topology

To understand the macroscopic mechanical behaviors of responsive DNA hydrogels integrated with DNA motors,we constructed a state map for the translocation process of a single FtsKc on a single DNA chain at the molecular level and then investigated the movement of single or multiple FtsKc motors on DNA chains with varied branch topologies.Our studies indicate that multiple.FtsKc motors can have coordinated motion,which is mainly due to the force-responsive behavior of individual FtsKc motors.We further suggest the potential application of motors of FtsKc,together with DNA chains of specific branch topology,to serve as strain sensors in hydrogels.

The spatial scaling effect of the discrete-canopy effective leaf area index retrieved by remote sensing

The leaf area index(LAI) is a critical biophysical variable that describes canopy geometric structures and growth conditions.It is also an important input parameter for climate,energy and carbon cycle models.The scaling effect of the LAI has always been of concern.Considering the effects of the clumping indices on the BRDF models of discrete canopies,an effective LAI is defined.The effective LAI has the same function of describing the leaf density as does the traditional LAI.Therefore,our study was based on the effective LAI.The spatial scaling effect of discrete canopies significantly differed from that of continuous canopies.Based on the directional second-derivative method of effective LAI retrieval,the mechanism responsible for the spatial scaling effect of the discrete-canopy LAI is discussed and a scaling transformation formula for the effective LAI is suggested in this paper.Theoretical analysis shows that the mean values of effective LAIs retrieved from high-resolution pixels were always equal to or larger than the effective LAIs retrieved from corresponding coarse-resolution pixels.Both the conclusions and the scaling transformation formula were validated with airborne hyperspectral remote sensing imagery obtained in Huailai County,Zhangjiakou,Hebei Province,China.The scaling transformation formula agreed well with the effective LAI retrieved from hyperspectral remote sensing imagery.

Research on Auto-Classification Method of Remote Sensing Images in Mountainous Areas——An Application in Southwest of China

In mountainous areas, it is the undulant terrain, various types of geomorphic and land use that make the remote sensing images great metamorphism. Moreover, due to the elevation, there are many areas covered with shadow, clouds and snow that make the images more inaccurate. As a result, it would be very difficult to carry out auto-classification of RS images in these areas. The study took Southwest China as the case study area and the TM images, SPOT images as the basic information sources assisted by the auxiliary data of DEM, NDVl, topographical maps and soil maps to preprocess the images. After preprocessing by topographic correction and wiping off clouds, snow and shadows, all the image data were stacked together to form the images to be classified. Then, the research used segmentation technology and hierarchical method to extract the main types of land use in the area automatically. The results indicated that the qualitative accuracies of all types of land use extracted in Southwest China were above 90 percent, and the quantitative accuracies was above 86 percent. The goal of reducing workloads had been realized.