Effect of geometrical parameters on forming quality of high-strength TA18 titanium alloy tube in numerical control bending

The forming quality of high-strength TA18 titanium alloy tube during numerical control bending in changing bending angle β, relative bending radius R/D and tube sizes such as diameter D and wall thickness t was clarified by finite element simulation. The results show that the distribution of wall thickness change ratio Δt and cross section deformation ratio ΔD are very similar under different β; the Δt and ΔD decrease with the increase of R/D, and to obtain the qualified bent tube, the R/D must be greater than 2.0; the wall thinning ratio Δto slightly increases with larger D and t, while the wall thickening ratio Δti and ΔD increase with the larger D and smaller t; the Δto and ΔD firstly decrease and then increase, while the Δti increases, for the same D/t with the increase of D and t.

Photochemical Process Modeling and Analysis of Ozone Generation

Air pollution in modern city and industrial zones has become a serious public concern in recent years in China. Significance of air quality assessment and emission control strategy design is increasing. Most studies in China focus on particulate matter(PM), especially PM2.5, while few account for photochemical secondary air pollutions represented by ozone(O3). In this paper, a procedure for air quality simulation with comprehensive air quality model with extensions(CAMx) is demonstrated for studying the photochemical process and ozone generation in the troposphere. As a case study, the CAMx photochemical grid model is used to model ozone over southern part of Beijing city in winter, 2011. The input parameters to CAMx include emission sources, meteorology field data, terrain definition, photolysis status, initial and boundary conditions. The simulation results are verified by theoretical analysis of the ozone generation tendency. The simulated variation tendency of domain-wide average value of hourly ozone concentration coincides reasonably well with the theoretical analysis on the atmospheric photochemical process, demonstrating the effectiveness of the procedure. An integrated model system that cooperates with CAMx will be established in our future work.

Fuzzy Synthetic Evaluation of Water Quality of Naoli River Using Parameter Correlation Analysis

In order to improve the effectiveness of Fuzzy Synthetic Evaluation (FSE) models, a Parameter Correlation Analysis (PCA) was introduced into the FSE and a case study was carried out in the Naoli River in the Sanjiang Plain, Northeast China. The basic principle of the PCA is that the pairs of parameters which are highly correlated and linear with each other would contribute the same information to an assessment and one of them should be eliminated. The method of the PCA is that a correlation relationship among candidate parameters is examined before the FSE. If there is an apparent nonlinear or curvilinear relationship between two parameters, then both will be retained; if the correlation is significant (p<0.01), and the scatter plot suggests a linear relationship, then one of them will be deleted. However, which one will be deleted? For solving this problem, a sensitivity test was conducted and the higher sensitivity parameters remained. The results indicate that the original data should be preprocessed through the PCA for redundancy and variability. The study shows that introducing the PCA into the FSE can simplify the FSE calculation process greatly, while the results have not been changed much.

How to Evaluate Human Capital？

A company is usually founded by individuals striving to achieve their own or broader goals. Goal achievement related to a company＇s operations is called business or the business process. Human capital （man＇s work, employees） is an important element of the business process, however its value is not disclosed on the assets side of the classical balance sheet. In order to shown assets, human capital has to be evaluated. Evaluation can be made in monetary or non-monetary terms. Non-monetary models for evaluating human capital include organisational and behavioural variables. These variables are not expressed in monetary terms, however, based on changes in their quality, one can assume the increased or decreased value of human capital within the company. The value of non-monetary models should not be underestimated, however monetary models are of greater importance. In this article, the most significant non-monetary and monetary models of human capital evaluation are discussed. Among non-monetary models the Michigan, Flamholz, and Ogan models are discussed. Among monetary models the replacement costs model, the opportunity costs model, the discounted wages and salaries model, and originally created dynamic model are discussed. A descriptive approach is used to identify the basic characteristics of existing models for evaluating human capital. According to these findings a different approach is taken in developing an original model. Dynamic model can efficiently overcome most of the practical problems and can be used as an appropriate estimator of human capital value expressed in monetary terms. The research limitations are that the dynamic model has not been sufficiently verified in practice. The model could prove to be directly applicable in those enterprises that would like to define the value of their human capital.

Online Monitoring the Products Quality by Measuring Cavity Pressure during Injection Molding

Injection molding is a complicated production technique for the manufacturing of polymer products. During injection molding, it＇s hard to predict molding quality; the injection molding parameters, such as mold temperature, melt temperature, packing pressure and packing time, affect the final properties of product. The cavity pressure is a significant key factor. Residual stress and injection molding weight are significantly affected by the cavity pressure. This study created an approach to predict weight of injection-molded by real-time online cavity pressure monitoring. This study uses a 6-inch with thickness lmm light guide panel and the largest area beneath the pressure curve of time as well as the maximum pressure as its characteristic. The upper and lower limits of the control are set to ＋2 standard deviations, and GUI （Graphical User Interface）-based LabVIEW software is used to perform calculation and analysis of the pressure curve. The results of the experiment show that the online internal cavity pressure monitoring system can effectively monitor the quality of the molded products. In 500 injection molding cycle tests, its error rate was less than 8%, whereas the deviation in mass of the molded products selected through the system＇s filtering process was successfully controlled to be within ±4%.

A decision-making model of gear process for green manufacturing

A decision-making model of gear process for green manufacturing is presented, which integrates the five objectives including the time, quality, cost, resource consumption and environmental impact of gear process together into the development of a strategy. Mathematical description is provided for the multi-objectives decision-making model. The expert judgment and the multi-fuzzy assessment theory are introduced to do sensible comparisons and give quantitative results. A case study on practical cutting tool selection in gear machining demonstrates that the proposed model is applicable.

Urban Air Quality Plans and Integrated Assessment Methodologies

The air quality directive （2008/50/EC （of the European Parliament and of the Council of 21 May 2008）） requires European Member States to design appropriate AQPs （air quality plans） for zones and agglomerations where the air quality does not comply with the limit values and to assess possible emission reduction measures to decrease concentration levels. The Portuguese agglomeration of Porto Litoral is one of the several European Union urban areas that had to develop and implement AQPs to reduce particulate matter （PM10）. The AQPs were initially designed based on a scenario approach and using an air quality model, which was applied over the study region for the reference situation with the current PM10 emissions, and for a reduction scenario with PM10 emissions re-estimated considering the implementation of abatement measures. Aiming to cost-efficiently optimize Porto Litoral PM10 abatement measures, the assessment procedure was repeated using an optimization approach based on the RIAT ＋ （regional integrated assessment tool ＋）. Porto Litoral urban area＇s technical and non-technical measures were characterized （including associated costs） and, through the application of the air quality model to 20 emissions abatement scenarios, S-R （source-receptor） relationships were created. This paper comparatively describes the air quality plans designed to improve PM10 levels in the Porto Litoral agglomeration based on both the scenario analysis and the optimization approach.

Numerical Study of Greenhouse Nocturnal Heat Losses

In this study we quantify and analyze different components of nocturnal losses from a heated greenhouse with the presence of vegetation for typical winter weather conditions in Marrakesh-Morocco,using a non linear model,based on the greenhouse heat and mass balance.It was found that 12% of the total input heat was dissipate as a sensible and latent leakage losses,66% was lost by convective exchange through air-inner cover.This gain of energy at the inner-cover is dissipated at the outer-cover by radiation(66%)and convection(34%).This results point toward some practical measures to reduce heat losses:increasing air tightness,using covering materials with low-emissivity in the long wave band or putting up an external thermal curtain should provide significant energy savings.